3Com 4200G Series Manual de usuario

3Com Switch 4200G

10G Interface Module

Installation Guide

1. XFP Interface Module

1.1 Appearance and front panel

Figure 1 Appearance of an XFP interface module

Figure 2 Front panel an XFP interface module

1.2 Installation

Step 1: Put on an ESD-preventive wrist strap and verify it is properly

grounded. Then remove the XFP interface module from the package.

Step 2: Loosen the filler panel mounting screws on the rear panel of the

switch with a screwdriver and remove the filler panel.

Step 3: Hold the fastening screws on the front panel of the XFP interface

module, and gently push the module in along the slot guide rail until the

module is in close contact with the switch.

Step 4: Tighten the fastening screws with a screwdriver to secure the XFP

interface module.

(1)

(2)

(4)

(3) (1)

(2)

(4)

(3)

(1): Switch (2): Optional module slot

(3): XFP interface module (4): Push-in direction

Figure 3 Installing an XFP interface module

Note: (1) Store the filler panel for future use.

(2) When tightening the fastening screws at both sides of the

optional module with a screwdriver or an electric screwdriver,

make sure that the torque is not bigger than 0.4 N-m.

1.3 Removal

Step 1: Put on an ESD-preventive wrist strap and verify it is properly

grounded.

Step 2: Loosen the fastening screws at both sides of the XFP interface

module using a screwdriver.

Step 3: Pull the XFP interface module towards you, until it completely

comes out of the switch chassis.

Note: When installing or removing an optional interface module, pay

attention to the following points:

(1) Do not use too much force in the operation, and do not

touch the surface-mounted components directly with your

hands.

(2) After removing an optional module, if no new module is to

be installed, install the filler panel as soon as possible to

prevent dust and ensure the normal ventilation in the switch.

2. XENPAK Optical Module

2.1 Appearance and front panel

Figure 4 Appearance of a XENPAK optical module

Figure 5 Front panel of a XENPAK optical module

2.2 Installation

Step 1: Put on an ESD-preventive wrist strap and verify it is properly

grounded. Then remove the XENPAK optical module from the package.

Step 2: Loosen the two mounting screws on the small cover plate in the

middle on the filler panel with a screwdriver and remove the small cover

plate.

Note: When installing a XENPAK optical module, you do not need to

remove the entire filler panel. Just remove the small cover

plate in the middle on the filler panel.

Step 3: Hold the fastening screws on the front panel of the XENPAK

optical module, and gently push the XENPAK optical module in along the

slot guide rail until the XENPAK optical module is in close contact with the

switch.

Step 4: Tighten the fastening screws on the XENPAK optical module with

a screwdriver to fix the XENPAK optical module on the filler panel.

(1): Switch (2): Filler panels for optional module slots

(3): Small cover plate (removed) in the middle on the filler panel

(4): Push-in direction (5): XENPAK Optical Module

Figure 6 Installing a XENPAK optical module

Note: (1) Retain the small cover plate for future use.

(2) Do not tighten the module screws more than 0.4 Nm.

(3) The switch 4200G supports hot swapping of XENPAK

optical modules.

2.3 Removal

Step 1: Put on an ESD-preventive wrist strap and verify it is properly

grounded.

Step 2: Loosen the fastening screws at each side of the XENPAK optical

module using a screwdriver.

Step 3: Pull the XENPAK module until it comes out of the switch chassis.

3Com Corporation 350 Campus Drive

Marlborough, Massachusetts 01752-3064 USA

www.3Com.com

Part Number: 10014918 Rev.AA

Published July 2006

Otros manuales para 4200G Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de 3Com

3Com

3Com 3CRWEASY96A Manual de usuario

3Com

3Com H3C S3100 16C SI Manual de usuario

3Com

3Com 3C433279A Manual de instrucciones

3Com

3Com OfficeConnect WX4400 Manual de usuario

3Com

3Com 3CRWE725075 Manual de usuario

3Com

3Com 3C16080 Manual de funcionamiento

3Com

3Com SuperStack II 3C16971 Manual de usuario

3Com

3Com 3CRWE90096A - Wireless Access Point Manual de usuario

3Com

3Com WL-560 Manual de usuario

3Com

3Com 3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card... Manual de usuario

3Com

3Com 3C421600A Manual de usuario

3Com

3Com 3C16630A Manual de usuario

3Com

3Com NETBuilder II Manual de usuario

3Com

3Com 3C421600A Manual de usuario

3Com

3Com Switch 4210 9-Port Manual de usuario

3Com

3Com WL-308 Manual de usuario

3Com

3Com 3C421600A Manual de usuario

3Com

3Com ETHERLINK III Manual de usuario

3Com

3Com 486 Manual de usuario

3Com

3Com AirProtect Enterprise Engine 6100 Manual de usuario

3Com

3Com WL-311 Manual de usuario

3Com

3Com 3CRWEASYG73 - 11g Wireless LAN Outdoor Manual de usuario

3Com

3Com 3C16685 Manual de usuario

3Com

3Com SWITCH 4050 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario