2N Access Unit M Manual de usuario
2N Access Unit M Installation
Manual
v.1.0
www.2n.com
2N Access Unit M Installation Manual
2 / 42
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Content
1. Product Overview
1.1 Components and Associated Products
1.2 Terms and Symbols
2. Description of Installation
2.1 Before You Start
2.2 Mechanical Installation
2.3 Electric Installation
2.4 Extending Module Connection
3. Detection of 2N Access Unit M using 2N® Network Scanner
4. Factory Reset
5. Maintenance
6. Status Signaling
7. Technical Parameters
7.1 General Drawings
8. Supplementary Information
8.1 General Instructions and Cautions
8.2 Troubleshooting
8.3 Directives, Laws and Regulations
2N Access Unit M Installation Manual
3 / 42
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1. Product Overview
Here is what you can find in this section:
1.1 Components and Associated Products
1.2 Terms and Symbols
Basic Features
2N Access Unit M is an elegant and reliable access IP system equipped with a number of useful
functions.
2N Access Unit M is a single-module access system available in several versions.
All the 2N Access Unit M versions include an integrated card reader module,which helps
control access using an RFID card. With additional software settings, you can use the card to
control more functions than just door lock switching too.
The 2N Access Unit M keypad versionhelps you control the electric lock switch by entering a
valid numeric code via the numeric keypad. With additional software settings, you can use the
numeric code to control more functions than just door lock switching too.
The 2N Access Unit M Bluetooth version helps you control the lock switch using the 2N®Mobile
Key application installed in your smartphone.
2N Access Unit M is designed as a robust, mechanically resistant IP55-rated access system,
which withstands any weather conditions without requiring additional accessories.
The installation of 2N Access Unit M is very easy. All you have to do is connect the system to
your LAN via a mains cable. Feed the access system either from a 12V power supply or your PoE
supporting LAN.
To configure 2NAccess Unit M use a PC equipped with any Internet browser. Use2N®Access
Commander to bulk manage extensive access system installations easily.
Advantages of Use
Elegant mullion design
Weather resistance (IP 55)
Easy wall (surface) mounting (brick/pasterboard walls, door frames)
Integrated electric lock switches with wide setting options
Integrated RFID card reader module
Bluetooth module version
Backlit touch keypad version
LAN (PoE) or external 12V power supply
Configuration using web interface
HTTP server for API configuration
SNTP client for time synchronization
SMTP client for email sending, Picture to Email feature
2N Access Unit M Installation Manual
4 / 42
•
•
•
•
•
•
•
•
•
TFTP/HTTP client for automated firmware and configuration upgrade and update
1.1 Components and Associated Products
Main Units
2N Part No.
916112
Axis Part No.
02393-001
2N®Access Unit M 13.56 MHz, NFC ready
is used for reading RFID cards in the 13.56 MHz bandwidth with the
NFC support. Combining an access reader and a controller, the
device is used for access control inside and outside of buildings.
The following RFID cards can be read:
ISO14443A (Mifare, DESFire)
PicoPass (HID iClass)
Felica
ST SR(IX)
2N®Mobile Key
2N Access Unit M Installation Manual
5 / 42
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Main Units
2N Part No.
916114
Axis Part No.
02394-001
2N®Access Unit M RFID 125 kHz, 13.56 MHz, NFC
is used for reading RFID cards in the 125 kHz and 13.56 MHz
bandwidths with the NFC support. Combining an access reader and
a controller, the device is used for access control inside and outside
of buildings.
The following RFID cards can be read:
EM4xxx
ISO14443A (Mifare, DESFire)
PicoPass (HID iClass)
Felica
ST SR(IX)
2N®Mobile Key
2N Part No.
916115
Axis Part No.
02395-001
2N®Access Unit M Bluetooth & RFID 125 kHz, 13.56 MHz, NFC
is used for reading RFID cards in the 125 kHz and 13.56 MHz
bandwidths with the NFC support. Combining an access reader, a
Bluetooth module and a controller, the device is used for access
control inside and outside of buildings.
The following RFID cards can be read:
EM4xxx
ISO14443A (Mifare, DESFire)
PicoPass (HID iClass)
Felica
ST SR(IX)
2N®Mobile Key
2N Access Unit M Installation Manual
6 / 42
•
•
•
•
•
•
•
•
•
•
•
Main Units
2N Part No.
916116
Axis Part No.
02396-001
2N®Access Unit M Touch Keypad & RFID 125 kHz, 13.56 MHz, NFC
is used for reading RFID cards in the 125 kHz and 13.56 MHz
bandwidths with the NFC support. Combining an access reader, a
touch keypad and a controller, the device is used for access control
inside and outside of buildings.
The following RFID cards can be read:
EM4xxx
ISO14443A (Mifare, DESFire)
PicoPass (HID iClass)
Felica
ST SR(IX)
2N®Mobile Key
License
2N Part No.
916012
Axis Part No.
01369-001
2N Access Unit NFC license
2N Part No.
9160401
Axis Part No.
02000-001
2N Access Unit Lift module license
2N Access Unit M Installation Manual
7 / 42
•
•
•
•
•
•
•
•
•
•
•
Electric Locks
Part No. 932071E BEFO 11211
12 V / 230 mA DC
low consumption
Part No. 932081E BEFO 11221 with momentum pin
12 V / 230 mA DC
low consumption
A very short electric pulse is enough to put the lock in the
OPEN position and unlock the door. After passage, the
lock gets in the CLOSED (relax) position again.
Part No. 932091E BEFO 11211MB with mechanical blocking
12 V / 230 mA DC
low consumption
You can set the lever mechanically into the OPEN or
CLOSED position. When OPEN, the lock is constantly
open, when CLOSED, it is a standard lock.
2N Access Unit M Installation Manual
8 / 42
•
•
•
•
•
•
•
•
•
•
•
•
•
Electric Locks
Part No. 932061E BEFO 11211MB with momentary pin, mechanical
blocking
low consumption
12 V / 230 mA DC
A regular lock with a built-in contact to indicate whether
the door is open or closed.
Part No. 932072EBEFO 31211
fail safe
12 V / 170 mA DC
The reverse lock is closed when electricity is switched
on. When electricity is interrupted, the lock is opened.
Part No. 932062E BEFO321211
fail-safe plus door signaling
12 V / 170 mA
The reverse lock is closed when electricity is switched
on. When electricity is interrupted, the lock is opened.
It contains a built-in contact to indicate whether the
door is open or closed.
•
Tip
FAQ: Electric locks – Differences between locks for 2N IP access systems
2N Access Unit M Installation Manual
9 / 42
•
•
•
•
•
•
•
•
•
•
Power Supply
Part Numbers
91378100E
91378100US
PoE injector – without cable
PoE injector –with EU cable
PoE injector – with US cable
For intercom supply via Ethernet cable where the PoE switch is absent.
Part Nos.
91341482E
91341482US
12 V / 1 A adapter
A stabilized power supply needs to be used where no PoE is available.
Part
No.932928
12 V transformer
for electric lock
Additional Modules
2N Part No.
9159010
Axis Part No.
01386-001
Security Relay
A handy add-on that significantly enhances door entry security
Prevents lock tampering. Installed between the intercom, from which
it is also supplied, and the lock to be controlled.
2N Access Unit M Installation Manual
10 / 42
•
•
•
•
•
Additional Modules
Part No. 9159013 Departure button
Connects the logic input for door unlocking from inside the building.
2N Part No.
9159012
Axis Part No.
01388-001
Magnetic door contact
Set for installation on a door, enabling the status of door opening to
be ascertained. Used when the intercom is used for door protection,
to detect when the door is not closed or forced open.
2N Part No.
9134173
Axis Part No.
01384-001
RFID card, Mifare Classic 1k, 13.56 MHz
Otros manuales para Access Unit M
1
Tabla de contenidos
