2N Helios IP Uni Manual de usuario

2N® Helios IP Uni

Door Access Intercom

Brief Installation Manual

Version: 1.0.2 www.2n.cz

Before You Start

1.1

1.1 Before You Start

Product Completeness Check

Please check the contents of your 2N®Helios IP Uni delivery:

1 2N®Helios IP Uni (selected model)

1 Torx 10 / Torx 20 double-ended wrench

1 2N®Helios IP Uni Installation Manual

1 mounting template

1 CD

1 A5 transparent name plate foil

1 spare name plate

1 brick flush mounting box

4 4x12 stainless steel, torx screws for plastics

2 cable ties

Mechanical Installation

1.2

1.2 Mechanical Installation

Mountiong Type Overview

Refer to the table below for a list of mounting types and necessary components.

Flush mounting –classic bricks

(also hollow bricks, thermally insulated

walls, etc.)

What you need:

A properly cut hole

Plaster, mounting glue, mounting foam or

mortar as necessary

Flush mounting –plasterboard

What you need:

Just a properly curt hole

Wall mounting (concrete and steel

structures, entry barrier columns, etc.)

What you need:

Wall mounting box

Part No. 9153003

Mechanical Installation

1.2

Caution

The warranty does not apply to the product defects and failures arisen as

a result of improper mounting (in contradiction herewith). The

manufacturer is neither liable for damage caused by theft within an area

that is accessible after the attached electric lock is switched. The product

is not designed as a burglar protection device except when used in

combination with a standard lock, which has the security function.

When the proper mounting instructions are not met, water might get in

and destroy the electronics. It is because the intercom circuits are under

continuous voltage and water infiltration causes an electro-chemical

reaction. The manufacturer’s warranty shall be void for products damaged

in this way!

Common Mounting Principles

Tip

Select flush mounting where possible to make your product elegant

looking, more vandal resistant and more secure.

Caution

Stainless steel screws are used for the 2N®Helios IP Uni assembly. Other

screws than stainless steel ones corrode soon and may aesthetically

deteriorate the surrounding environment!

Having removed the front panel, make sure that no dirt gets inside the

product (especially onto the sealing surface).

Mechanical Installation

1.2

Flush Mounting –Classic Bricks

1. Cut a wall hole using the template enclosed. Make sure

that all the required cables are available in the hole.

2. Unpack the plastic mounting box. Break out the cable

holes as necessary and make sure that the wall hole is

big enough for the box.

3. Wall up the mounting box making sure that the box is

aligned with the wall surface. Wait until the plaster

(mortar, mounting foam, etc.) sets.

4. Unscrew the front panel from the door intercom.

5. Connect the cables to the terminals or RJ connector as

described in the Electric Connection subsection.

6. You can use the cable tie for connection as shown:

Suggested cable fixation

Mounting completion –after electric installation!

7. Insert the intercom in the mounting box in the wall.

8. Tighten the intercom with the stainless steel screws included in the delivery. As the

screw holes are oval, you can perfect the vertical position before tightening.

9. We do not recommend you to insert the button tags now.

10. Replace the stainless steel front panel fixing it with the stainless steel screws you

unscrewed in step 4 above.

Mechanical Installation

1.2

Flush Mounting –Plasterboard

Tip

If this is your first plasterboard installation, check the

function of the intercom side clamps. Loosen and then

re-tighten the clamp screw to see how it turns

automatically and starts moving forwards in its slot.

Remember to return the clamp into the original position

after the check!

Caution

Check the plasterboard wall and room interior pressure

values (caused, e.g., by overpressure ventilation). If the

difference between the values is too great, separate the

intercom using, for example, the mounting box enclosed

and seal the cable passage to avoid loudspeaker

damage.

1. Cut a hole using the template enclosed (165 x 95 mm).

2. Unscrew the front panel from the door intercom.

3. Connect the cables in the hole to the terminals or RJ

connector as described in the Electric Connection

subsection.

4. You can use the cable tie for connection as shown on

previous page.

Mounting completion –after electric installation!

5. Insert the intercom in the hole keeping it in the vertical

position.

6. Loosen the four clamp screws one after another and then

retighten them slowly. They will turn aside automatically and

start moving forwards in their slots. You need about 10

turns to tighten the clamps completely. You can perfect the

vertical position before final tightening of the screws.

7. We do not recommend you to insert the button tags now.

8. Replace the stainless steel front panel fixing it with the

stainless steel screws you unscrewed in step 2.

Wall Mounting

Use the wall (surface) mounting box, part No. 9153003, and follow the instructions

enclosed.

Electric Installation

1.3

1.3 Electric Installation

This subsection describes how to connect 2N®Helios IP Uni into your Local Area

Network (LAN) and how to connect supply voltage and the electric lock.

PCB Connectors

Description of Connectors

LAN

LAN connector

OUT1

12V/700 mA switched

output

RELAY1

Relay NO/NC contacts

TAMPER

Tamper switch

POWER

12V/1A DC power input

RESET

RESET button

Electric Installation

1.3

LAN Connection

2N®Helios IP Uni is connected to the LAN via a RJ-45 terminated (connector X11)

UTP/STP cable (of category Cat 5e or higher). The system is equipped with the Auto-

MDIX function and so both the straight and crossed cable versions can be used

External Power Supply Connection

2N®Helios IP Uni can be fed either from an external 12V/1A DC power supply or from

the LAN equipped with the PoE 802.3af supporting network elements.

External Power Supply

An external 12V power supply is connected to terminal block X19. Use a 12V +- 15%

DC power source dimensioned to current intake of 1A at least (Part No. 91341481E) to

ensure a reliable function of your device.

PoE Supply

2N®Helios IP Uni is compatible with the PoE 802.3af (Class 0 –12.95W) technology

and can be supplied directly from the LAN via compatible network elements. If your

LAN in incompatible, insert the PoE injector, Part No. 91758100E, between

2N®Helios IP Uni and the nearest network element.

Electric Lock Connection

2N®Helios IP Uni is equipped with an electrically isolated relay switch with NO and NC

contacts (terminal block X17) and 12V/700mA switched output (terminal block X18),

to which a standard electric lock or another compatible electrical appliance can be

connected.

Tamper Switch Connection

2N®Helios IP Uni is equipped with a tamper switch for detection of unauthorized

penetration into the device. After correct and complete installation of the device the

tamper switch is closed. Tamper switch opens immediately when the front panel is

removed. Tamper switch contacts are available on terminal block X18.

Device Resetting

2N®Helios IP Uni is equipped with a RESET button. Push the button for more than 10s

to reset the factory default values, deleting all the data stored in the device. Push the

button shortly (< 1s) to restart the device without changing its configuration.

Button Tags –Insertion and Replacement

1.4

1.4 Button Tags –Insertion and

Replacement

Tag Printing

1. Every name plate includes a piece of foil, which can be written over manually,

using a waterproof permanent marker.

Note

Always use waterproof foil (enclosed or other) for the tags. Never use

paper or ink jet printing to avoid damage due to water leakage!

Tag Inserting / Replacing

2N®Helios IP Uni provides an intuitive, easy

access to the name plates. The tags are easy

to insert and replace even without a manual.

You need not remove the front panel and

thus are not exposed to the risk of loss of

components while replacing the tags.

1. Loosen the name plate screw using

the wrench enclosed, for example.

You can open the name plate window

like a door without losing the

tightened screw.

2. Remove the used or blank name tag

and insert a new tag.

3. Close the name plate window and

tighten the screw appropriately.

4. Check the click effect of the buttons:

if the button fails to click properly

when pressed (when moved by

approx. 0.5 mm), the tag is too thick

or thin. Make sure that the button

clicks when you press it on either

end.

Otros manuales para Helios IP Uni

Tabla de contenidos

Otros manuales de Sistema de intercomunicación de 2N

2N Helios IP Force Manual de usuario

2N Helios IP Hoja de instrucciones

2N Helios IP Manual de usuario

2N Helios IP Manual del operador

2N Helios Uni Manual de usuario

2N SingleTalk Manual de usuario

2N Indoor View Manual de usuario

2N Helios IP Manual de usuario

2N Lift1 Compact Guía de referencia

2N EntryCom Guía de solución de problemas

2N Helios IP Safety Manual de usuario

2N Helios IP Hoja de instrucciones

2N Helios IP Manual de usuario

2N Helios Force Manual de usuario

2N Helios IP Manual de usuario

2N Helios Uni Manual de usuario

2N Helios IP Manual de usuario

2N Helios IP Force Manual de usuario

2N Helios IP Verso Manual de usuario

2N IP Verso Manual de usuario

2N C-CURE 9000 Manual de usuario

2N Helios IP Hoja de instrucciones

2N Helios IP Force Manual de usuario

Manuales populares de Sistema de intercomunicación de otras marcas

Bticino

Bticino LINEA 3000 Manual de usuario

MSI

MSI MSI-140 Manual de usuario

golmar

golmar Stadio Plus Manual de usuario

CyberData

CyberData 011211 series Manual

Vidos

Vidos duo M1021 Manual de usuario

Vimar

Vimar ELVOX 7539/E Manual de usuario

SSS Siedle

SSS Siedle BTSV 850-03 Manual de usuario

Dahua

Dahua VTO Series Manual de usuario

Elvox

Elvox 5651 Manual de usuario

Videx

Videx VIDEOKIT Series Manual de usuario

Rocom

Rocom Doortello Business FW T2.05W2.04 Manual de usuario

Viking

Viking E-35-EWP Manual de usuario

Safeguard Supply

Safeguard Supply LRA-EX1000 Manual de usuario

SSS Siedle

SSS Siedle BFCV 850 Series Manual de usuario

GRD

GRD MAX V2 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Aiphone

Aiphone IE-8MD Manual de usuario

Perel

Perel EDB4 Manual de usuario