- 05 - - 06 -
EN
DE
FR
ES
IT
EN
DE
FR
ES
IT
A.Turning the receiver on/off:
Be sure to switch the button to the "ON" position
when using the Alarm kit.
You can turn off the alarm when needed by
switching the button to the "OFF" position.
B. Selecting the work mode:
The receiver can work as a doorbell or work as an
alarm.
To select the working mode, switch the button
on the side of the receiver to one of the
following positions:
C. Selecting the notification mode:
The receiver will notify after the PIR sensor has
detected a car or someone passing by with a
chime/alarm sound, flashing LED, or chime/alarm
sound and flashing LED at the same time.
To select the notification mode, press the Sound
and Flash
button on the side of the receiver.The
receiver will display the current notification mode.
Keep pressing the Sound and Flash button and
stop when you have reached the preferred mode.
D: Pairing additional PIR sensors/receivers to the
alarm system:
Up to 5 PIR sensors can be paired with one
receiver.You can also extend the alarm system
with any number of receivers.This is only possible
when the PIR sensor and receiver are working on
the same frequency. Pair additional PIR sensors/re-
ceivers using the same pairing process as
described below.
The following pairing instructions are relevant to
receiver SKU O00QH-0512 and PIR sensor SKU
a. Chime - The receiver will work as a doorbell and
play a high volume "Ding Dong" sound.
b. Low - The receiver will work as a doorbell and play
a low volume "Ding Dong" sound.
c.Alarm - The receiver will work as an alarm and play
an alarm sound.
PIR sensor:
The PIR sensor is powered by 3 x AAA batteries,
please insert the batteries using the following
procedure:
·Remove the screw on the back of the PIR sensor
with a screwdriver. Next, remove the battery
compartment cover.
·Insert 3 x AAA batteries into the battery
compartment, using the correct polarity to
eliminate the danger of fire.
·Replace the battery compartment cover and
tighten the screw.
4. Operation:
Receiver:
The receiver can be powered by 3 x type C batteries
or by an adapter (output:DC 6V).
a. If powered by batteries, please insert the batteries
using the following procedure:
·Remove the screws on the back of the receiver
with a screwdriver. Next remove the battery
compartment cover.
·Insert 3 x C type batteries into the battery
compartment, using the correct polarity to
eliminate the danger of fire.
·Replace the battery compartment cover and
tighten the screw.
b. If powered by an adapter (recommended adapter
SKU OUS00-0278): Insert the adapter’s connector
into the DC power input jack on the side of the
receiver, then plug into a power outlet.
Safety Note:
For the receiver:
·Be sure to remove all batteries before connecting
to the adapter and plugging into a safe power
outlet.
·Do not expose the receiver to water spray or
O00QH-0513
After the receiver and PIR sensor have been
powered, press the
Pairing button on the side of the
receiver. Next trigger the PIR sensor.If pairing is
successful, the receiver will play a ringing/alarm
sound.It normally takes about 30 seconds for the
PIR sensor and receiver to pair. If there is no
pairing within 30 seconds, the receiver will
automatically exit pairing mode.Please try pairing
again.
E: Resetting and re-pairing:
If the receiver rings but the PIR sensor has not
been triggered,or the PIR sensor interferes with
another receiver, it may be necessary to wipe the
current pairings and pair again.
For Resetting the PIR sensors, press the Pairing
button and hold for 5 seconds.The receiver will
ring and flash a LED, then all the PIR sensors
information will be deleted.
You can now re-pair the wanted PIR sensor.
F: Installation:
The PIR sensor and receiver can be mounted on a
wall or just put on a flat place.
To mount on a wall:
Select a suitable location for the receiver and PIR
sensor.
Drill holes on the wall. Next push the wall plugs
into the drilled holes and then insert the screws
into the wall plugs.Finally, mount the PIR
sensor/receivers on the screws.
Note:
• The recommended installation height for the PIR
sensor is 3.3-4.9ft (1.0-1.5m)
• The PIR sensor detecting angle is 45 degree and
detecting distance is 16.4-26.2ft (5-8m). Install
the PIR sensor in key monitoring areas such as
the entrance to a garage, store, or house.
• If installing the PIR sensor outside, note that
moving leaves and branches, strong wind, and
drastic changes in temperature can affect and
influence the sensor.
• The PIR sensor and receiver can connect up to
300ft/100m without any obstacles.
• The PIR sensor’s transmitting frequency is
water drops and do not place liquid-filled objects
such as vases or opened drink containers on or
near the receiver and the power outlet.
·If power by batteries, replace them when
exhausted with the same type and voltage
battery.
·Remove the batteries or unplug the adapter from
the power outlet if the Alarm kit is not to be used
for an extended period of time.
For the PIR sensor:
·The PIR sensor is powered by 3 x AAA batteries.
When exhausted, replace it using the same type
and voltage batteries.
·Always insert the batteries using the correct
polarity to eliminate the danger of fire.
·Keep old and new batteries away from children.
·Old batteries should be properly disposed using
safe environmental practices.
·Remove the batteries from the PIR sensor if you
do not intend to use the Alarm kit for an
extended period of time.
Low voltage indication: When the batteries are
exhausted, the LED indicator on the receiver and PIR
sensor will flash once every second to remind you to
replace the batteries.
433MHz and its range can be affected by metal,
walls,concretes, and interfering signals from
other electronic appliances with the same
frequency, including televisions, radios, and
cookers.
• Avoid placing the PIR sensor and receiver near to
the above mentioned electronic appliances.
• Do not expose the PIR sensor and receiver to
direct sunlight or high temperatures, otherwise
overheating may cause them irreparably
damaged.
• Do not install the PIR sensor and receiver near
any source of naked flames such as lighted
candles.
• Please test the PIR sensor and receiver at the
potential installation locations before actual
installation to confirm range and transmission
effectiveness.
