ZyXEL Communications NSA-2400 Manual de usuario
NSA-2400
Network Storage Appliance
Quick Start Guide
Version 1.00
6/2006
Edition 1
NSA-2400 Quick Start Guide
2
Overview
The NSA-2400 (the NSA) is a network storage
device for file sharing, data backup and data
protection in small (home) offices and/or
medium-sized offices.
This guide shows you how to:
1Install hard drives
2Make NSA Connections
3Access the NSA using NDU (NSA
Discovery Utility) or your web browser
4Set up the NSA using the wizard
5Map the NSA to a network drive from any
computer
Note: See the User’s Guide for more details and specifications on the NSA.
Requirements
You need the following before you start:
•NSA
• Included CD containing the NDU (NSA Discovery Utility) and Genie Backup Manager
• Power cord and power supply (external)
• 8-wire Ethernet cable for Gigabit Ethernet
• Up to four SATA-1 (Serial Advanced Technology Attachment) compatible hard disk(s) with 15-pin SATA power
connectors
• Screwdriver to install the hard disks in the disk trays
• USB cable (optional: you only need this if you want to expand storage capacity by connecting compatible USB
drives (version 2))
• Computer with Network Interface Card (NIC) and TCP/IP installed
• Network access device such as a switch or hub.
1 Install Hard Drives
Note: Hard drives are NOT hot swappable. The NSA must be turned off before you remove or install
hard drive(s).
1Pull the tab on the left of the front door of the NSA to open it.
NSA-2400 Quick Start Guide
3
2Pull out the latch and grip the sides of the
tray to remove disk tray 1. Be careful not
to break the latch. Disk bay 1 is labelled on
your NSA (the top-left bay).
3Place the disk tray on a flat surface with
the panel facing up. Place a hard disk with
the screw holes facing up on the same
surface and slide it into the disk tray.
Secure it with the screws as shown.
4Push the top of the tray back into NSA disk
bay 1 until it snaps into place and push the
latch up as shown.
5Repeat steps 1 to 3 for other hard drives
that you may have.
2 Make the NSA
Connections
1Connect the Ethernet port on the rear of the NSA to a hub, switch, or
router on your network using an Ethernet cable. Use an 8-wire Ethernet
cable for Gigabit connections.
NSA-2400 Quick Start Guide
4
2Connect one end of the power cord to the power socket on the rear of the
NSA and the other end to the external power supply. Connect the external
power supply to a power outlet.
3Turn on the power by pressing in the power button on the front of the NSA.
Look at the front panel lights. The PWR light turns steady green. The SYS
light turns steady green after the NSA has booted successfully (it takes
about 50 seconds). The LAN light turns on if the NSA Ethernet port is
properly connected to your network. It blinks while transmitting or receiving
traffic.
Note: To turn off the NSA, press the power button in once only. The SYS
light blinks red indicating the NSA is shutting down.
3 Access the NSA
You can access the NSA in one of two ways: using the NDU (NSA Discovery
Utility) or directly entering the NSA IP address into your web browser.
3.1 Use the NDU to Discover the NSA IP Address
Use the NDU (NSA Discovery Utility) on a Windows computer if your network has a DHCP server that will
assign the NSA an IP address and/or if you have many NSAs in your network.
Note: The Genie Backup program uses the same network port as the NDU to discover the NSA. To
avoid a port conflict, do not run the Genie Backup at the same time as the NDU.
1Insert the included CD into your CD-ROM drive.
The next screen should automatically display
(autorun). Click the Setup icon.
NSA-2400 Quick Start Guide
5
2The NDU installation wizard begins. Follow the
installer instructions. Click Finish to complete the
installation.
3In Windows XP, click start, All Programs, ZyXEL
NSA-2400, ZyXEL NSA-2400 Discovery Utility to run the NDU.
For other Windows operating systems, procedures should be
similar. If your computer has more than one network card, then
you will first be prompted to select a network interface card.
4The NDU main screen appears listing all
hostnames, IP addresses and status of all NSAs
in your network. Click the icon under Admin to
see the main web configurator screen as shown
in Section 4 on page 6. (If you want to change the
NSA IP address, click the icon under Config. If
you want to map the NSA to a Windows network
drive, click the icon under Map (see Section 5 on
page 14). To refresh the screen, click Discover.)
3.2 Direct Access Via Web Browser
If the NSA cannot get an IP address from a DHCP
server, then the default IP address of the NSA
reverts to 192.168.1.3. Before directly entering the NSA IP address into your web browser, you must make
sure that your computer and the NSA are in the same subnet. This section shows you how to set your
Windows NT/2000/XP computer to have an IP address in the same subnet as the NSA. Refer to your User’s
Guide for detailed IP address configuration for other operating systems.
1In Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control Panel.
2In Windows XP, click Network Connections. In Windows 2000/NT, click Network and Dial-up
Connections.
NSA-2400 Quick Start Guide
6
3Right-click Local Area Connection and then click Properties.
4Select Internet Protocol (TCP/IP) (under the General
tab in Win XP) and click Properties.
5The Internet Protocol TCP/IP Properties screen opens
(the General tab in Windows XP).
6Select the Use the following IP address and enter an IP
address from 192.168.1.1 to 192.168.1.254 excluding
192.168.1.3 (the NSA) and any other IP addresses in this
range already being used by a device on your network.
7Click OK to close the Internet Protocol (TCP/IP)
Properties window.
8Close the Local Area Connection Properties window
and then the Network Connections screen.
9Launch your web browser and enter “192.168.1.3” as the
web site address.
4 NSA Wizard Setup
1Access the NSA using the NDU or web configurator directly.
2When you first access the NSA web configurator, you may see
this screen telling you that this is a secure connection using
HTTPS. Click OK to continue.
NSA-2400 Quick Start Guide
7
3The web browser client uses certificates to
authenticate the NSA. The default NSA certificate
will most likely show a name and certification
authority mis-match; however encryption is still
performed. Click Yes to proceed.
4When you access the NSA web configurator, the
login screen appears. The default user name and
password are ‘admin’ and ‘1234’ respectively. Click
Login.
5It is recommended that you change the default
password. You can also enter an e-mail address to
which NSA alerts can be sent here (you must enter
e-mail server information in the wizard or Log Alert
screen). Click Apply to save your changes and go
to the next screen or ignore this screen and click
Skip to go to the next screen.
NSA-2400 Quick Start Guide
8
6The first time you access the NSA web
configurator, you are prompted to run the setup
wizard. Click Run Setup Wizard.
4.1 Setup Wizard
Each time you click Next in the wizard, your settings
are saved to the NSA. Click Back to return to a
previous screen in the wizard.
1Click Next to begin the
wizard.
2If you want to change the
network settings of the NSA, click
Modify Network Settings. You can
also do this using the NDU
(recommended). If you change the IP
address, then you will have to use the
new IP address to access the web
configurator again. Click Next to
continue.
NSA-2400 Quick Start Guide
9
4.1.1 Disk Setup Wizard
3This screen is the Disk Setup
Wizard (this screen can be
accessed separately from the main
NSA screen). Skip this wizard to
have the NSA use the current or
default volume configuration.
• Choose RAID 1 if you
have two or four disks in
the NSA; half the disk
space is used for data
backup. If you have four
disks, you could choose
RAID 5 where data parity
and striping allow you to
recover data even if one
disk fails. Choose SIN-
GLE if you have just one
disk or have multiple disks
but don’t need disk
backup. Click Next to
continue (without saving
anything yet).
NSA-2400 Quick Start Guide
10
• Disk data is lost if you
reconfigure a volume.
Select the I Under-
stand... checkbox and
then click Apply to save
the Disk Setup Wizard
settings. You now return
to the main installation
wizard.
4.1.2 Return to Main
Wizard
4The next screen allows
you to enable FTP on
the NSA. You can use
FTP and/or Windows
explorer (CIFS) to
transfer files to or from
the NSA. Select Enable
Anonymous FTP
Access to allow any
user to log into the NSA
using an ‘FTP’ user
name or ‘anonmyous’
without giving a
password. If you clear
Enable Anonymous
FTP Access then you
must create a user
account and associated
password. Use that username and password to log into the NSA via FTP.
Otros manuales para NSA-2400
5
Tabla de contenidos
Otros manuales de Hardware de red de ZyXEL Communications
ZyXEL Communications
ZyXEL Communications VMG4005-B60A Manual de usuario
ZyXEL Communications
ZyXEL Communications G-4100 v2 Manual del operador
ZyXEL Communications
ZyXEL Communications WAP6405 Manual de usuario
ZyXEL Communications
ZyXEL Communications NSA-2400 Manual de usuario
ZyXEL Communications
ZyXEL Communications X6004 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZyAIR B-320 Manual de usuario
ZyXEL Communications
ZyXEL Communications IES-1248-51V Manual
ZyXEL Communications
ZyXEL Communications FMG3010-R20A Manual de usuario
ZyXEL Communications
ZyXEL Communications IES-1248 Manual de usuario
ZyXEL Communications
ZyXEL Communications Network Device P-2602 Manual de usuario
ZyXEL Communications
ZyXEL Communications NSA-220 Plus Manual de usuario
ZyXEL Communications
ZyXEL Communications EOC350 Series Manual de usuario
ZyXEL Communications
ZyXEL Communications PoE12 Series Manual de usuario
ZyXEL Communications
ZyXEL Communications NSA-2400 Manual de usuario
ZyXEL Communications
ZyXEL Communications VMG4005-B50B Guía de instalación
ZyXEL Communications
ZyXEL Communications ZyWALL SSL 10 Manual de usuario
ZyXEL Communications
ZyXEL Communications IES-612-51A Manual de usuario
ZyXEL Communications
ZyXEL Communications NSA-220 Plus Manual
ZyXEL Communications
ZyXEL Communications FMT3211 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZyWall Manual de usuario
ZyXEL Communications
ZyXEL Communications FiberHome AN5516-06 Guía
ZyXEL Communications
ZyXEL Communications Multi-service Access Platform MSAP2000 Manual de usuario
ZyXEL Communications
ZyXEL Communications IES-6000 Series Manual de usuario
ZyXEL Communications
ZyXEL Communications ZyWALL ATP Series Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
