ZyXEL Communications Omni TA128 Manual de usuario

Omni TA128

Quick Start Guide

Version 2.08

JiH5<

5:'2

4:+84+:

))+99

52;:/549

Omni TA128 Quick Start Guide ZyXEL

Page ii

The contents of this document may not be reproduced (in any part or as a whole) or

transmitted in any form or by any means without the written permission of the publisher.

Notice: ZyXEL does not assume any liability arising out of the application or use of any

products, or software described herein. Neither does it convey any license under its

patent rights nor the patents rights of others. ZyXEL further reserves the right to make

changes in any products described herein without notice. This document is subject to

change without notice.

Acknowledgments

Trademarks and brands mentioned in this manual are used for informational purposes

only. All trademarks and brand names remain the properties of their respective owners.

ZyXEL Omni TA128 Quick Start Guide

Page iii

Table of Contents

One - Introduction...............................................................1

Unpacking Your Omni TA............................................................................................ 1

Key Features of the Omni TA....................................................................................... 2

Front panel of the Omni TA128.................................................................................... 3

Back Panel of the Omni TA128.................................................................................... 4

Two - Ordering an ISDN Line .............................................5

Three - Installing your Omni TA128 Hardware .................7

Connecting Hardware................................................................................................... 7

Power-on Self-Test........................................................................................................ 8

Four - Driver Installation and Configuration.....................9

Installing the Windows 95 Driver................................................................................. 9

Installing the ISDN Configuration Manager (ICM).................................................... 10

Configuring your Omni TA using the ICM................................................................. 10

Five - Configuring Windows 95 Dial-Up Networking .....15

Configuring Dial-Up Networking for One B-Channel................................................ 15

Configuring Dial Up Networking for Two B-Channels.............................................. 18

Appendix A - ISDN Line Provisioning ...........................A-1

Provisioning requirements for North America.......................................................... A-1

Appendix B - Configuring the Omni TA128 from a

Terminal Program...........................................................B-4

Configuring your TA using AT Commands.............................................................. B-4

Testing your Connection........................................................................................... B-8

Appendix C - Contacting ZyXEL ..................................C-10

ZyXEL Phone Numbers.......................................................................................... C-10

Online Access ......................................................................................................... C-10

ZyXEL Omni TA128 Quick Start Guide

Introduction Page 1

One - Introduction

The ZyXEL Omni TA128 ISDN Terminal Adapter sets a new price/performance standard

for the explosively growing Internet and telecommuting applications.

When used with off-the-shelf Internet or remote access client software, the Omni TA128

enables mobile or home users to connect to the Internet or branch offices over ISDN lines

Hassle Free! The same device also allows a user to connect to the analog world via a

modem, fax machine, or telephone connected directly to the Omni TA.

To take advantage of constant new developments, the Omni TA128 employs flash

EPROMs, which allow for convenient uploading of newly available firmware which

preserves your hardware investment.

ZyXEL’s expertise in data compression has been brought to the Omni TA. With its

V.42bis compression and Hi/fn™ LZS®Compression on the B Channels, the Omni

TA128 can effectively communicate at speeds up to 460Kbps over ISDN lines.

The Omni TA128 also has two analog ports to connect analog devices such as fax

machines, modems, and telephones. Two different analog devices can communicate over

the two B channels to two different locations simultaneously, so you can send a fax and

make a voice call at the same time. The analog ports also recognize standard DTMF tones

as well as pulse dialing.

Unpacking Your Omni TA

Your Omni TA128 should come with the equipment listed below. If any item is missing

or damaged, please contact your Dealer or ZyXEL Customer Service Department

immediately.

1) Omni TA128 ISDN Terminal Adapter

2) ZyXEL AC power adapter

3) RJ-45 ISDN telephone cable

4) RS-232 25-pin to 25-pin shielded cable

5) DB-25 female to DB-9 female adapter

6) Warranty/registration card

7) User's Manual

8) Quick Start Guide

9) CD ROM with bundled software

10) Firmware & driver diskette

11) ISDN Configuration manager diskette

Omni TA128 Quick Start Guide ZyXEL

Page 2Introduction

Key Features of the Omni TA

Speed and Compatibility



Plug and Play support for Win95 environment



Full compatibility with both ISDN and remote PSTN via ISDN



Multiple signaling protocol compatibility with the following network switches:

DSS1, 1TR6, NI-1, AT&T 5ESS, and Northern Telecom DMS 100



Supports X.75, V.110, V.120 and PPP B Channel protocols



B Channel speeds of 56Kbps(in-band Signaling) and 64Kbps(out-of-band

Signaling)



112Kbps/128Kbps channel bundling: MLP and Multilink PPP (RFC1717)



Hi/fn™ LZS®Compression over PPP



V.42bis data compression over X.75 & V.120



ZyXEL ISDN AT Commands

Intelligent Features



Automatic ISDN/analog call detection



Two analog telephone jacks (POTS ports)



Supplemental phone service support for:



Call Waiting



Three Way Calling (conference)



Call Transfer



Call Forwarding



Message Waiting



Reminder Ring



Distinctive Ring



Push-button switch for quick dial and tear down



Easy-to-use configuration software.



Flash EPROM memory for easy firmware upgrades

Technical Specifications



Status Display: 13 LED indicators



Flow Control: Software XON/XOFF or hardware CTS/RTS



Configuration Setting: Software programmable with nonvolatile memory for

profile storage



Diagnostics: Self test and loopback



DTE Ports: Asynchronous: 460.8Kbps (DTE 1), 115.2Kbps (DTE 2)

Physical Characteristics



Line Interface: RJ-45 for ISDN BRI S/T or U interface



Analog Ports: Two RJ-11 Telephone Jacks



DTE Interface: DB-25 for Primary DTE; DB-9 for Secondary DTE



Dimensions: 7 1/8” x 5 1/4” x 1 5/16”; Weight: 14oz

ZyXEL Omni TA128 Quick Start Guide

Introduction Page 3

Front panel of the Omni TA128

This section describes the front panel controls and indicators and their functions.

LED Description

PWR Poweron indicator; lights up when the Omni TA128 power is turned ON.

LNK Link indicator - Indicates your connection status with the local switch, lights up

when link is active. Flashing when attempting to make a connection.

B1 B1 channel connection indicator; lights up when B1 channel is established; flashes

when there are re-transmissions of packets.

B2 B2 channel connection indicator; lights up when B2 channel is established; flashes

when there are re-transmissions of packets.

AA Auto-answer indicator; lights up when the Omni TA128 is in Auto Answer mode;

flashes when it rings.

DTR (1) Data terminal ready indicator; lights up when the Computer connected to DTE

Port 1 indicates that it is ready for communication by raising the corresponding

RS232 signal.

TX (1) Transmit data indicator; flashes when the Computer is transmitting data to DTE

Port 1 of the Omni TA.

RX (1) Receive data indicator; lights up when the DTE/Computer is receiving data from

DTE Port 1 of the Omni TA.

DTR (2) Data terminal ready indicator; lights up when the Computer connected to DTE

Port 2 indicates that it is ready for communication by raising the corresponding

RS232 signal.

TX (2) Transmit data indicator; flashes when the Computer is transmitting data to DTE

Port 2 of the Omni TA.

RX (2) Receive data indicator; lights up when the DTE/Computer is receiving data from

DTE Port 2 of the Omni TA.

Phone 1 Hook status of POTS port 1. Lights up when the telephone/handset is off-hook.

Phone 2 Hook status of POTS port 2. Lights up when the telephone/handset is off-hook.

6=8

/9*4 *:+  *:+  6.54+

241 ( ( '' *:8 :> 8> *:8 :> 8>  

Omni TA128 Quick Start Guide ZyXEL

Page 4Introduction

Front Panel Button

Quick dial/Tear down: When the Omni TA128 is in command state, pressing the front

panel button causes it to dial the default phone number pre-stored in the NVRAM. The

default number pointer to the telephone directory is assigned by theAT*Dncommand.

When the Omni TA128 is on-line, pressing the button will tear down the connection and

bring it into command state.

Factory Reset: To restore the Omni TA128 to its factory default settings, turn the power

ON while pressing and holding the front panel button. Continue holding the button for 3

to 5 seconds after turning the power on. A loopback test will also be performed during

this procedure.

Note: The SPID & ISDN switch settings will be cleared when the Omni TA128 is

reset in this manner.

Back Panel of the Omni TA128

You will find the following switch and connectors on the back panel of Omni TA

ON/OFF Power switch; turns the Omni TA128 ON or OFF

POWER Input terminal for power adapter

To DTE 1 Serial port DB-25 female connector for connection to the serial port

of a computer or terminal.

To DTE 2 Serial port DB-9 female connector for connection to the serial port of

a second computer or terminal.

ISDN ISDN RJ-45 terminal jack; connects to a S/T interface or a U

interface (depending on the model purchased).

PHONE 1

PHONE 2 RJ-11 terminal jacks for connecting analog devices (phone, fax,

answering machine, etc.)

212))

32:(5 72 '7(  72 '7(  ,6'1 3+21(  3+21( 

ZyXEL Omni TA128 Quick Start Guide

Ordering an ISDN Line Page 5

Two - Ordering an ISDN Line

The following are step-by-step instructions for ordering your ISDN line for use with the

Omni TA. Wit each step, we have provided spaces to record the information provided

by your phone company. This information will be used in the coming chapters for the

configuration of your Omni TA.

Step 1 Contact your telephone company

Use the following phone numbers to contact your local telephone company.

Phone Company Phone Contact World Wide Web

Amertiech 800-TEAM-DATA www.ameritech.com

Bell Atlantic 800-570-ISDN www.bellatlantic.com

Bellsouth 800-858-9413 www.bellsouth.com

Nynex 800-GET-ISDN www.nynex.com

Pacific Bell 800-4PB-ISDN www.pacbell.com

Southwest Bell 800-734-7630 www.swbell.com

US West 800-603-6000 www.uswest.com

Step 2 Determine your ISDN switch type

Ask the telephone company representative what switch type is available in your area.

Check the appropriate box below.



AT&T 5ESS Point to Point



AT&T 5ESS Multipoint



AT&T 5ESS NI-1



Northern Telecom NI-1



Northern Telecom Custom

Step 3 ISDN Ordering Codes (IOC)

Tell the phone company representative the Omni TA128 supports IOC-S and EZ ISDN-

1capability packages.

If your phone company does not use ordering codes, provide them with the line

provisioning information for the correct ISDN switch type. See Appendix A - for line

provisioning information.

Step 4 Get ISDN Directory Numbers and SPIDs

Your phone company will provide your Directory (phone) and SPID numbers. Fill in

these numbers below.

SIPD # 1: SPID # 2:

Directory # 1: Directory # 2:

Omni TA128 Quick Start Guide ZyXEL

Page 6Ordering an ISDN Line

Step 5 Specify Supplementary Voice Services

The Omni TA128 supports the following Supplementary Voice Services. Tell your phone

company which of these features you would like to utilize on your ISDN line.



Conference Call (3-way)



Call Transfer



Drop Call



Message Waiting



Call Waiting



Call Forwarding



Distinctive Ring



Reminder Ring

Note: Some of the Supplementary Voice Services may not be available for use with all

telephone companies. Check with your telephone company for more details.

Some of the Omni TA’s voice features require Feature Activator Keys or Buttons to be

activated. The NI-1 default key settings are shown in the table below. If your phone

company does not use the NI-1default key settings, simply ask the phone company

representative for the proper settings and record them below.

Conference Call



default: “60”



other:

Call Transfer



default: “61”



other:

Drop Call



default: “62”



other:

Message Waiting



default: “63”



other:

Call Forwarding



default: “57”



other:

ZyXEL Omni TA128 Quick Start Guide

Installing your Omni TA128 Hardware Page 7

Three - Installing your Omni TA128 Hardware

This chapter describes the installation process for the Omni TA128 ISDN terminal

adapter.

Connecting Hardware

Connecting the Omni TA128 to the Computer

Power OFF

1) Turn OFF the power to your computer

2) Make sure the power switch on the Omni TA128 is in the OFF (down) position.

Connect Cables to Your Computer

1) Connect the male end of the 25 pin cable to the serial port of the Omni TA.

2) Connect the other end of the 25 pin cable (female end) to your computer’s serial

(COM) port. A 25 pin to 9 pin adapter has included in the Omni TA128 retail

package in the event you do not have a 25 pin serial port available.

3) Note: If you have a Macintosh, you will need a Macintosh hardware handshaking

modem cable for the connection.

Connect ISDN Line

1) Connect the RJ-45 connector to the “ISDN” jack on the back of the Omni TA.

2) Note: If you have purchased the S/T interface model, refer to your users manual

section, "Connecting the Omni TA128 to Your ISDN Line".

3) Connect the other end of the RJ-45 cable to your ISDN wall jack.

Serial

DTE2

DTE1

Power

To ISDN Line or NT-1

Optional 2nd

Computer

Phone 2

Phone 1

Otros manuales para Omni TA128

Tabla de contenidos

Otros manuales de Adaptador de ZyXEL Communications

ZyXEL Communications

ZyXEL Communications ZYAIR B-200 Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA-401 v2 Guía de referencia

ZyXEL Communications

ZyXEL Communications G-470 Manual de usuario

ZyXEL Communications

ZyXEL Communications N220 - Manual de usuario

ZyXEL Communications

ZyXEL Communications G-210H Manual de usuario

ZyXEL Communications

ZyXEL Communications AG-220 Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA-470 Manual de usuario

ZyXEL Communications

ZyXEL Communications DMA-1000 Series Manual de usuario

ZyXEL Communications

ZyXEL Communications NWD2205 Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA-400 Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA-401 - V3.0.5 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZyXEL PLA-401 v3 Manual de usuario

ZyXEL Communications

ZyXEL Communications N220 - Manual de usuario

ZyXEL Communications

ZyXEL Communications ZyXEL NWD2105 Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA6457 Manual de usuario

ZyXEL Communications

ZyXEL Communications M-102 Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA-401 Series Manual de usuario

ZyXEL Communications

ZyXEL Communications G-202 Manual de usuario

ZyXEL Communications

ZyXEL Communications OMNIMPRI Instrucciones de uso

ZyXEL Communications

ZyXEL Communications PLA4101 Manual de usuario

ZyXEL Communications

ZyXEL Communications AC240 Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA-402 v3 Manual de usuario

ZyXEL Communications

ZyXEL Communications Powerline Ethernet Multiplug Center PLA491 Manual de usuario

ZyXEL Communications

ZyXEL Communications PLA450 Series Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario