Zerotech Vengeance 1-6X24 Manual de usuario
ZEROTECH RIFLESCOPES
INSTRUCTION MANUAL
vengeance (MODEL 1-6X24) /
‘ANY OWNER, ANY PROBLEM, ALWAYS COVERED’
3
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
CONTENTS
INTRODUCTION
LIFETIME WARRANTY
SCOPE FEATURES
SETTING THE DIOPTRE
MOUNTING YOUR SCOPE
ZEROING YOUR RIFLE
RESETTING THE TURRETS AFTER ZEROING
RETICLE ILLUMINATION FEATURE
BATTERY INSTALLATION
SCOPE CARE
RETICLES
WARRANTY & CONTACT INFORMATION
BULLET DROP DETAILS
ZEROTECH INFORMATION
4
5
6
7
9
11
14
15
16
17
18
19
20
21
PAGES
4ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
WELCOME TO THE ZEROTECH RIFLESCOPE FAMILY!
Customer First - We listened to you and came up with a family of riflescopes that will
satisfy the needs of our most discerning and experienced customers.
Backed by Experience - ZeroTech enjoys 55 years of experience in the Optics Market
supplying high quality brands to retailers throughout Australia and the Asia Pacific.
Built for the Australian Shooter - Designed and built to endure the harsh conditions of
the Australian bush and the exacting demands of the precision shooter.
Lifetime Warranty - Be safe in the knowledge that your scope is backed by our Triple A
Lifetime Warranty: ‘ANY OWNER, ANY PROBLEM, ALWAYS COVERED’
Bespoke Reticles - Practical Reticles for the Everyday Shooter.
INTRODUCTION
5
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
LIFETIME WARRANTY
BACKED FOR LIFE!
Be safe in the knowledge that your scope is
backed by our Triple A Lifetime Warranty:
- Fully transferable, covers accidental damage as
well as defects in materials and workmanship.
- No receipt or warranty card is required.
- We will repair or replace product with equal or
similar value and/or specifications.
- We will return product to you at no charge. ‘ANY OWNER, ANY PROBLEM,
ALWAYS COVERED’
6ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
Windage turret
Windage turret cap
Elevation turret
Elevation turret cap
Magnification power
change ring
Reticle illumination
adjustment dial
Illumination battery cover
Dioptre lock ring
Magnification
throw lever
Ocular
Objective
30mm maintube
VENGEANCE 1-6X24
SCOPE FEATURES
7
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
BEFORE YOU START USING YOUR SCOPE, IT IS EXTREMELY IMPORTANT
TO MAKE SURE YOU HAVE ADJUSTED THE DIOPTRE CORRECTLY. THE
CORRECT DIOPTRE SETTING WILL ENSURE THAT YOUR RETICLE REMAINS
CLEAR AND SHARP THROUGHOUT THE ENTIRE FOCAL RANGE OF YOUR
SCOPE. TO SET YOUR DIOPTRE, FOLLOW THE STEPS BELOW;
SETTING THE DIOPTRE
1. Loosen the dioptre locking ring and unscrew away
from the ocular for several revolutions.
2. Adjust the magnification to 1x.
3. Whilst looking through the scope at an object
between 15 to 50 metres away, rotate the ocular
until the object appears at true 1x magnification. - Loosen the
dioptre locking ring
8ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
NEVER LOOK THROUGH YOUR SCOPE DIRECTLY AT THE SUN.
4. Adjust the magnification to full power (6x) and confirm the reticle is well focused.
The reticle should appear sharp and crisp from edge to edge. Make small
adjustments on the ocular to sharpen the appearance of the reticle, if required.
5. Once the desired setting has been achieved, tighten the locking ring against the
ocular, being careful not to rotate the ocular and disturb the dioptre setting.
- Tighten dioptre locking ring
- Set magnification to
6 X. Confirm reticle is
sharp and crisp
- Set magnification to 1 X
- Rotate ocular to achieve
true 1 X image
9
ZEROTECH - INSTRUCTION MANUAL
VG1624-IR_V1_int. 10/2021
- BEFORE MOUNTING YOUR SCOPE TO A FIREARM, IT IS ESSENTIAL THAT
YOU CONFIRM THAT YOUR FIREARM IS UNLOADED AND NO AMMUNITION
IS PRESENT IN YOUR WORKSPACE.
- TO AVOID DAMAGE AND TO PRESERVE YOUR WARRANTY, YOUR SCOPE
SHOULD ALWAYS BE MOUNTED BY AN EXPERIENCED PROFESSIONAL.
MOUNTING YOUR SCOPE
1. Once you are satisfied the base(s) is correctly fitted to the receiver of your firearm,
proceed to fit the rings to the base(s) and ensure the ring clamps are tightened to
the recommend torque settings as specified by the manufacturer.
2. With the ring tops removed, place the scope in the ring bases and gently slide the
scope back and fourth in the ring bases to ensure the scope slides freely. If the scope
does not slide freely, lapping of the rings may be necessary to avoid damage to the
scope maintube. ZeroTech always recommends the use of high quality rings and bases
10 ZEROTECH - INSTRUCTION MANUAL VG1624-IR_V1_int. 10/2021
to ensure the best possible fitting of your scope.
3. Avoid mounting the scope with the rings contacting the junction of the maintube/
erector housing, magnification ring/ maintube junction or the objective/ maintube
junction.
4. It is essential to confirm that no part of the scope is contacting the barrel or receiver
when the scope is mounted in the rings.
5. Once you have confirmed the fit of the scope in the ring bases, fit the ring tops and
tighten the ring top bolts to between 22–25 in lbs or 2.5–2.8NM.
6. ZeroTech highly recommends the use of a scope level (bubble level) fitted to the
rings or the scope maintube to ensure the reticle can consistently be aligned with
the fall of gravity every time a shot is fired. This is particularly important for precision
shooting applications.
*If your level mounts to the maintube of the scope, follow the same guidelines as observed
for scope ring fitting to ensure the level does not damage the maintube of your scope.
Tabla de contenidos
