Zenoah G260PU-EI Guía de aplicación
OWNER’S SERVICE MANUAL
848-ES5-93A0 (812)
WARNING
•These engines are designed for radio
controlled products.
•When replacing parts, use only parts
which have been certified by Zenoah.
•Zenoah assumes that no responsibility for
these engines that are modified or used for
any other applications.
•Purchaser has all responsibility against
any laws and regulations existing in the
countries, Zenoah is exempt from such
laws and regulations.
•Read and completely understand this
OWNER'S SERVICE MANUAL before
operating these engines.
MODEL:
G260PU-EI – for radio control Airplane
2
1. Safety Precautions
•This manual describes the engine. For its mounting and control, see the
instruction manual for the model airplane.
•Engine is designed for use on model airplane. If it is used for any other
purpose, we cannot be responsible for its reliability, safety and any
laws/regulations in the countries.
•Use genuine parts for replacement.
•Check the propeller, every time. If it is damaged, replace it with a new one.
•If the propeller hit something while the engine is in operation, immediately
stop the engine and check it.
•Start the engine on a flat surface without pebble stones.
•When mixing the fuel, or operating the engine, carry it out in a well-ventilated
place.
Gauge Rotor
Fig.2 Fig.3
Fig.4
3
2. Engine Assembling
The carburetor, muffler, air-funnel and sensor are not assembled at factory.
Make sure that the assembling for such parts are done according to the 2.1 and 2.2.
Tightening torques: see page 9
1. Bolt (01252-30550)
2. Muffler (T2075-15110)
3. Gasket (1140-13141)
4. Screw (0263-30408)
5. Engine
6. Gasket (T2075-13150)
7. Carburetor (T2075-81000)
8. Lever, choke (T2070-82410)
9. Air-funnel (848ES08300)
10. Spacer (1142-83110)
11. Screw (0263-30555)
Make sure that gasket and carburetor are mounted as the picture.
If carburetor is mounted upside down position, the engine does not start as
carburetor does not work correctly.
CAUTION
Fig.1
Fig.2: Affix the gauge to magneto.
Fig.3: Turn the crankshaft until gauge
position at top.
Fig.4: Fix the sensor on the mount while
pushing the sensor.
• Take away the gauge from the rotor.
Carburetor muffler and air-funnel assembling
2.1
Sensor assembling
2.2
4
3. Engine Mounting
4. Ignition Unit Mounting
Make sure that the G260PU-EI is mounted on the aircraft grade plywood with more
than 8mm of thickness or a mount of equivalent strength and is firmly fixed with 4 bolts.
If necessary, please reinforce the firewall and the around.
[ NOTE ]
1. Be sure to set flat washers or metal plate on the reverse side of the mount to prevent
bolts from sinking into the mount. Before be sure to check for loose bolts.
2. Since the engine is equipped with a float-less carburetor with a diaphragm pump, the
direction of cylinder and position of fuel tank can be freely selected .
3. The Fuel head between carburetor and bottom of fuel tank must be less than 100
mm (4 inches).
4. If the rubber joint is placed between the engine and the body for anti-vibration, check
if the rubber is too week and select the proper hardness of the rubber, in order to
avoid the unexpected vibration under operating engine RPM zone.
5. Tighten the nut (M8) with a torque of 80~120 kg·cm
applying about 10~15 kg by hand as shown in the
figure.
(NOTE)
Do not tighten the nut (M8) with too large torque,
that may damage the stud.
Nut (M8)
8cm
10~15kg
(80~120kg·cm)
1. Make sure to install the power switch. (switch is not supplied)
2. Push the sparkplug cap all the way over the sparkplug. (use gloves)
3. Fixate the unit within the fuselage, as shown in the diagram. Do not wrap the unit by
the sponge, cloth or the like.
4. The temperature of the bottom surface (D) of the unit, in particular, will rise. Thus,
when fixating surface (D), make sure to leave sufficient space (a gap).
The temperature of the unit may rise to as high as 70~80°C, depending on
the operating environment and conditions, but this is not abnormal.
However, make sure not to touch this part or you could risk being burned.
Fig.5
5
5. Propeller, Rotor & Screw Propeller
The recommended prop sizes are as shown in the table bellow.
Be sure to use a propeller which makes the engine speed approximately
7,500~8,500 rpm while the airplane is flying.
When mounting the spinner, set a pin on the hub with more than 3mm of
diameter, thus preventing slipping.
CAUTION
Diameter x Pitch ( in.)
18 x 7 ~ 12, 16 x 10 ~ 14
Bolt (4mm)
Sparkplug wire
Sensor wire
Sensor
Unit
Battery wire
For charging
Switch
Capacity: 3A (or higher)
(not supplied)
Battery 4.8V
1500~2700mA
(not supplied)
Use of anything
other than an 4.8V
battery is prohibited.
Ground wire
surface D
Sponge & cloth
Gap: 5mm or
more surface D
surface D
surface D
surface D
Fig.6
Fig.7
6
6. Fuel
7. Starting
•Mix gasoline (octane over 85 / premium gasoline) and high grade 2 cycle engine oil
(mixing use type; F3C grade or ISO EGC grade) at mixing ratio 25~40:1.
•The mixing ratio may be decided according to the oil recommendation.
[ NOTE ]
1) Never use any alcohol fuel or alcohol added fuel, or the rubber parts in the
carburetor. Will be damaged.
2) Gasoline is very flammable. Avoid smoking, bringing any fires near fuel.
3) To prevent all possible problems on fueling system, make sure to use the fuel filter
which has more than 300 mesh or equivalent and gasoline proof rubber pipe or
equivalent.
Incorrect fuel filter use causes engine trouble like carburetor's fuel passage stuffing
or piston surface scratching etc.
Make sure to fix a spinner and make sure that the helpers hold the airplane firmly. Also
make sure that the electric motor has a power enough to run the engine at minimum
1,100 rpm.
●How to start
a. Fill the fuel tank with the fuel.
b. Choke the carburetor.
c. Set the throttle valve at idle position or at the position slightly open from the idle
position (Never open the throttle more than 1/4 of full throttle stroke).
d. Turn the engine by electric motor until first combustion noise is heard.
e. Open the choke and keep the throttle valve at slight open position from idle position.
f. Turn the engine by electric motor, then the engine will start.
•Too much run by electric motor at choke condition may have a chance to wet
spark plug.
In this case, change the spark plug or dry it thoroughly and remove fuel rest in
the cylinder by turning engine under full throttle, open choke and without
spark plug installing.
•When engine is warm, carburetor choking may not be necessary.
•Hand flip starting is prohibited to prevent the hazards.
CAUTION
7
The carburetor is provided with 3 adjust screws which are set to the best
(approximately) positions by our company, but they may need a little adjustment
depending on the temperature, atmospheric pressure (altitude), etc. of the area where
the engine is used. Start the engine without making any adjustments. Make
readjustments only when the engine shows any mal-running.
Standard opening of each needle as follows;
Idle Screw:
Turning this screw clockwise increases the idling R.P.M. Turning it
counterclockwise decreases the idling R.P.M
Low Speed needle:
This is the fuel adjust screw (not the air screw). Turning this needle clockwise
makes the mixture gas leaner and turning it counterclockwise makes it richer.
Set this needle at a position which is 1/4 open from best mixture (maximum R.P.M.)
position.
High Speed needle:
Turning this needle clockwise makes the mixture gas leaner and turning it
counterclockwise richer. Set this needle at a position which is 1/8~1/4 open from the
maximum R.P.M. position while the airplane is on ground.
1. Do not tighten the High and Low Speed needles too firmly.
2. When the unit has just started and the engine is not warm enough, there may
be insufficient acceleration and the engine may be stopped. Be sure to
perform idling before operation.
CAUTION
Low Speed needleHigh Speed needle
Idle Screw
8. Carburetor Adjustment
HL
1 3/8±1/41 3/8±1/4
Fig.8
8
11. Maintenance
9. Engine Break-In
10. Operation
No specific break-in is required.
The engine is gradually broken-in as it is used and the output is also gradually
increased.
For checking the whole conditions of the airplane, it may be better to operate the
engine at slow RPM for 1/3 tank and mid-high RPM for 2/3 tank.
•The engine is already tuned up to get high performance, and needs correct
maintenance to keep such high performance.
•The details for operation as an airplane may be provided from the airplane
manufacturer.
•Always keep well maintenance according to the Maintenance clause described in
this owner's service manual.
1) MAINTENANCE CHART
Before Every Every
Items Action Use 25 hours 100 hours Note
Leakage, Check ✔✔✔
Damage/Crack
Idling Speed Check/Adjust ✔✔✔
Spark Plug(gap) Check/Adjust ✔✔Replace if necessary
Cylinder(barrel) Check/Cleaning ✔✔ ↑
Piston, Ring Check/Cleaning ✔✔ ↑
Muffler & Bolt Check/Cleaning ✔✔✔ ↑
Bearings Check/Cleaning ✔✔ ↑
Crank Shaft Check/Alignment ✔↑
Rotor Check ✔✔ ↑
Propeller Hub Check/Alignment ✔✔ ↑
9
2) SPECIFICATIONS & TECHNICAL DATA
Items unit Specifications
Type — Air Cooled
Bore x Stroke mm 34x28
Displacement cm325.4
Effective Compression Ratio 8.4
Type (Walbro) WT-645
Carburetor Venturi (mm) ø12.7
Air Cleaner —
Starting — Electric Motor
Ignition Type Battery Ignition
Spark Plug STD Y82
Idle Speed rpm 1800 (APC 18x8)
Max. Power kW/rpm NA
Max. Torque N·m/rpm NA
Fuel Consumption g/kW·H NA
Weight kg 1.35 (✽)
(✽): Without Ignition System Specifications are subject to change without notice.
3) CARBURETOR
Items Unit Standard Measuring Device
Metering Lever set mm 1.65 ± 0.16 Vanier
MPa 0.13~0.23
Inlet Valve Opening Pressure Leak Tester
kg/cm21.3~2.3
MPa 0.07~0.17
Inlet Valve Closing Pressure Leak Tester
kg/cm20.7~1.7
4) TIGHTENING TORQUE
Standard
Items Screw Size Remarks
N·m kg·cm
Carburetor M5 (P=0.8) 3.4 35
Insulator M5 (P=0.8) 4.4 45
Rotor M8 (P=1.0) 12.7 130
Cylinder M5 (P=0.8) 6.9 70
Crankcase M5 (P=0.8) 5.9 60
Spark Plug M10 (P=1.0) 7.8 80
Muffler M5 (P=0.8) 8.8 90
Stud (hub) M6 (P=1.0) 9.8 100 with Locktight glue
Nut, Propeller M8 (P=1.25) 9.8 100
10
13. Service Guide
1. REMOVING PISTON PIN (Fig.9)
1) Remove snap rings from both sides of the
piston pin.
2) Engage the rod assy(1101-96220) to the
piston pin and gently tap with a plastic
hammer to push out the pin while holding
piston firmly.
Hard hammering may damage the big end of
the connecting rod.
2. INSTALLING PISTON (Fig.10)
1) Make sure to point the arrow mark on the
piston to the exhaust side.
2) Fit the circlip in the groove so as to face the
end gap below.
Deformed circlip may come off during engine
operation and damage the engine.
CAUTION
CAUTION
Fig.9
Fig.10
12. Special Tools
Part Name Part No. External Appearance Usage
1Puller Assy 1490-96101 To remove rotor.
2Piston Stopper 4810-96220
3Rod Assy 1101-96220 To remove/install piston pin.
4Hex Wrench 3304-97611
5Snap Ring Pliers 5500-96110 To remove snap ring.
To hold crankshaft when
disassembling/assembling
the rotor.
For socket screw of
4mm, 5mm and 6mm.
Tabla de contenidos
Otros manuales de Motor de Zenoah
Zenoah
Zenoah 966669901 Manual de usuario
Zenoah
Zenoah G231PUM Guía de aplicación
Zenoah
Zenoah G380PU Manual de usuario
Zenoah
Zenoah G320RC Manual de usuario
Zenoah
Zenoah G200PU-EI Manual de usuario
Zenoah
Zenoah G25B-1 Manual de usuario
Zenoah
Zenoah Zenoah Manual de usuario
Zenoah
Zenoah Komatsu G230RC Guía de aplicación
Zenoah
Zenoah G620PU Manual de usuario
Zenoah
Zenoah G240RC Manual de usuario
Zenoah
Zenoah G800BPU Manual de usuario
Zenoah
Zenoah G4LS-D Manual de instrucciones
Zenoah
Zenoah G231 Heli Manual de usuario
Zenoah
Zenoah G300PUM Manual de usuario
Zenoah
Zenoah G450PU Manual de usuario
Zenoah
Zenoah G320RC Manual de usuario
Zenoah
Zenoah G230PU Manual de usuario
Zenoah
Zenoah G261LS Manual de instrucciones
Zenoah
Zenoah G4K-D Manual de instrucciones
Zenoah
Zenoah AIR G26 Manual de usuario
