ZENEC Z-E4626/H Guía de inicio rápido
P a g e | 1
Z-E4626/H Installation Notes
Z-E4626/H Installation Notes V1.1
Below is a list of standard settings that we recommend be set on the Universal Zenec Z-E4626/H. Some of the below
settings are only the “recommended settings” based off our testing but they may not suit the personal preferences
of the End User so it is important to show them how to change these settings.
Antenna Remote Wire –The Blue P. ANT wire on a Zenec is a switch wire and is not designed to power antenna
boosters in vehicles or antennas that require a 12v supply. We recommend connecting these wires to an
accessory/ignition source.
Steering Controls & Speed_IN –Due to the variety of different Mercedes Benz Vehicles this head unit is compatible
with, either a CTSMC011.2 (W447 Vito) or a CX401-MB01 has been provided for CAN-Bus and Steering Wheel
Controls. Connect the steering control output wire from either interface to the grey wire labelled “IR In” which is on
the same connector as the Microphone and Camera input of the Zenec device. The Pink Speed_IN wire is not used.
Bluetooth Pairing –Please READ
The Z-E4626/H has dual phone pairing functionality which allows for two handsets to be connected and used at the
same time. However, for this feature to work correctly you will need to follow the below instructions.
•Initiate the pairing of the first (most used) device
•Wait until the phone book and call history are completely downloaded to the Zenec device. This may take
some time on the first connection and will depend on the number of contacts on the phone.
•While this process is taking place, avoid using the phone for SMS or phone calls.
•Once it has completed then you can initiate the pairing of the second phone as per the above instructions.
1) After the installation is completed and BEFORE you set up anything on the device please follow the below
instructions to perform a “Load Factory”.
Go To Setup in the Home Screen and Press Device
Setup (bottom right as highlighted) then Press Help
Press OK next to Load Factory and Press Yes to confirm.
The unit will reboot.
PLEASE READ BEFORE INSTALLATION
P a g e | 2
2) Access the Car Setup Menu as Highlighted to setup the reverse camera and vehicle settings.
`
In Car Setup you can program the Zenec for reverse
camera and other important settings
Park Assist –This is where you program the Zenec
for reverse camera
`
Reverse Audio Assist –Here you can program what will
happen to the audio when Reverse is engaged
Driver Position –Please make sure that this setting is
changed to Right Hand Drive
3) Access the Bluetooth Setup Menu as Highlighted in the below Screen Shot
1. Microphone –Choose External or Internal*
2. Display Order –Change this setting to First Name
so that the BT Contacts will be display by First
Name
3. Device Name –This allows the End User to change
the BT Broadcast name so they can easily identify
the BT device they are connected too.
*We strongly advise installing an external microphone
for optimum voice quality
4) Access the TFT Settings Menu
`
TFT Settings –This menu allows you to change the
device brightness settings and controlled how the
device is dimmed for low light or night mode.
TFT Control –We recommend changing this setting to
Car which will adjust the brightness when the cars lights
are turned on. Navi will adjust the brightness by the
current GPS Location.
Tabla de contenidos
Otros manuales de Sistema de vídeo para coche de ZENEC
ZENEC
ZENEC ZE-NC3810 Manual de usuario
ZENEC
ZENEC ZE-NC2010 Manual de usuario
ZENEC
ZENEC ZE-NC2040 Manual de usuario
ZENEC
ZENEC Z-E2026 Hoja de instrucciones
ZENEC
ZENEC ZE-NES14 Manual de usuario
ZENEC
ZENEC Z-N528 Manual de usuario
ZENEC
ZENEC Z-N626 Manual de instrucciones
ZENEC
ZENEC Z-E3726 Hoja de instrucciones
ZENEC
ZENEC Z-E2060 Manual de usuario
ZENEC
ZENEC Z-R1030 Manual de usuario
ZENEC
ZENEC E GO ZE-NC3152 Manual de usuario
ZENEC
ZENEC E3776 Manual
ZENEC
ZENEC ZE-NC520 Instrucciones de montaje
ZENEC
ZENEC Z-E3756 Manual técnico
ZENEC
ZENEC Z-E3776 Guía del usuario
ZENEC
ZENEC ZE-NC4110 - MOUNTING INSTRUCTIONS FOR SANTA... Manual de usuario
ZENEC
ZENEC Z-E2014M Manual de usuario
ZENEC
ZENEC ZE-NC524 Manual de usuario
ZENEC
ZENEC ZEM-W600DDMM Manual de usuario
ZENEC
ZENEC Z-E2055 Manual de usuario
