YOKOYAMA KP6210 Manual de usuario
KP6210
KP6210A
210x297
"IMPORTANT SAFETY INSTRUCTIONS"
DANGER -
WARNING -
"SAVE THESE INSTRUCTIONS"
When using an electrical appliance, basic safety should always be followed, including the
following:
Read all instructions before usingthis sewing machine.
To reduce the risk of electric shock:
1. An appliance should never be left unattended when plugged in.
2. Always unplug this appliance from electric outlet immediately after using and before cleaning.
To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Read the instructionscarefully before you use the machine.
2. Keep the instruction at a suitable place close to the machine and hand it over if you give
the machine to a third party.
3. Use the machine only in dry locations.
4. Never leave the machine unattended with children or elderly people due to they may not
be able to estimate the risk.
5. This appliance can be used by children aged from 14 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. (For Europe)
6. Children shall not play with the appliance. (For Europe)
7. Cleaning and user maintenance shall not be made by children without supervision.
(For Europe)
8. Always switch off the machine if you carry out preparation for work (change the needle,
feed the yarn thru the machine, change the footer, etc.).
9. Always unplug the machine if you leave it unattended, to avoid injury by expediently
switch on the machine.
10. Always unplug the machine if you carry out maintenance (oiling, cleaning).
11. Don’t use the machine if it’s wet or in humid environment.
12. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
13. If the LED lamp is damaged or broken, it must be replaced by a qualified person, in order
to avoid a hazard.
14. Never place anything on the pedal.
15. Do not use the machine if the air vents are blocked. Keep the ventilation openings of the
machine and foot pedal free from lint, dust etc.
16. The machine may only be used with foot pedal type 4C-333B.
17. Do not dispose of electrical appliances as municipal waste,use separate collection
facilities.
18. Contact your local government for information regarding the collection systems available.
19. If electrical appliances are disposed of in landfills or dumps, hazardous substances can
leak into the groundwater and get into the food chain,damaging your health and well-being.
20. When replacing old appliances with new ones, the retailer is legally obligated to take back
your old appliance for disposal at least for free of charge.
21. The appliance is not to be used by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction. (For outside Europe)
22. Children being supervised not to play with the appliance. (For outside Europe)
This sewing machine is intended for household use only.
23. For the foot controller, If the supply cord is damaged, it must be replaced by the manufacturer
or its service agent or a similarity qualified person in order to avoid a hazard.
For European version
Dimensions: 438 mm x 200 mm x 315mm
Mass of the equipment: 6.8 kg
Rated Voltage: 220~240 V
Rated Frequency: 50 Hz
Rated input: 45 W
Using ambient temperature: Normal temperature
36
User operates an error warning,
Thick fabric sewing,
Darning sewing
37
20
21
22
23
24
25
26-29
30
31
31
32-33
34
35
, Darning stitches
33. Large extension plate (Optional part)
1. Threading tension dial
MACHINE IDENTIFICATION
1. KNOWING YOUR SEWING MACHINE
2. Bobbin winder thread guide
3. Thread guide
4. Take up lever
5. Face plate
6. Thread cutter
7. Extension table (Accessory box)
8. Bobbin winder shaft
9. Bobbin winder stopper
10. Horizontal spool pin
11. Hand wheel
12. Power/light switch
13. Foot control socket
14. Cord socket
15. Needle clamp screw
16. Presser foot lifter
17. Handle
18. Buttonhole lever
19. Needle threading lever
20. Presser foot release button
22. Presser foot
23. Feed dog
24. Needle plate
25. Thread guide
21. Presser foot screw
26. Threading guide
27. Needle
28. Bobbin case cover release button
29. Bobbin case cover
30. Power line cord
32. Instruction manual
31. Foot control (Type:4C-333B)
12
3
4
5
6
7
89
* Optional parts for KP6210
* Standard parts for KP6210A
ACCESSORIES
1. Needles
2. Bobbins (4 total - 1 in machine)
3. Auxiliary spool pin
4. Spool pin felt discs
5. Spool pin cap
7. Buttonhole opener/seam ripper and brush
6. Screwdriver for needle plate
9. Darning plate
10. Zipper foot
12. Satin stitch foot
11. Blind stitch foot
13. Buttonhole stitch foot
8. Oiler
(Optional part)
The Foot that comes on your
Sewing machine is called the
General Purpose Foot and will
be used for the majority of your
sewing.
The Satin Foot (12) should be used
for most of your decorativesewing
especially
HONEYCOMB , STAR etc.
When purchasing additional bobbins,
be sure they are Class 15 J.
14. Screwdriver
14
SETTING UP YOUR MACHINE
Be sure to wipe off any surplus oil from needle plate area
before using your machine for the first time.
POWER LINE CORD/FOOT CONTROL
NOTE: When foot control is disconnected, the machine
will not operate. (Model KP6210A)
Always disconnect the machine from power supply
by removing the plug from the wall-outlet.
POWER/LIGHT SWITCH
Your machine will not operate until the power/light switch
is turned on.The same switch controls both the power and
the light.
When servicing the machine, or changing needle, etc.,
machine must be disconnected from the power supply.
1
2
3
Set power/light switch at "OFF"
Machine socket
Power line cord
Pin plug
Foot control
wall outlet
(1) Connect the power cord and plug as illustrated.
(2) Connect the foot pedal into the machine socket as
illustrated.
SPOOL PINS
HORIZONTAL SPOOL PIN for normal thread spool
Place thread spool on the pin and secure with a spool cap to ensure smooth
flow of thread. If the thread spool has a thread retaining slit, it should be
placed to the right.
Select the correct spool pin cap according to the type and diameter of the spool.
The spool pin cap should always be larger than the spool itself.
VERTICAL SPOOL PIN for large thread spool
PRESSER FOOT LIFTER
There are three positions for your presser foot.
Lower the presser foot to sew.
1.
Raise the lifter to the middle position to insert or remove fabric, and to
change presser foot.
2.
Lift it to its highest position to insert or to remove thick fabric.
3.
DARNING PLATE
Use the darning plate when you need to control fabric feeding for button
sewing, free motion work and free motion darning.
Raise needle and presser foot, and position darning plate onto the needle plate
with the two pins on the back inserted to the holes of needle plate.
Attach the spool pin. Place the felt disc over it. Place a thread spool on the
spool pin.
Push bobbin winder shaft to far left position , if it is not already there. Place
bobbin onto shaft with end of thread coming from top of bobbin. Push bobbin
winder shaft to the right until it clicks. Hold onto end of thread.
Remove the bobbin cover plate by pushing the release button to the right.
Bobbin cover will pop up to allow you to remove the cover.
With your finger placed gently on top of the bobbin, pull the thread until it
reaches the slot (B).
NOTE: Sewing can start without picking up the bobbin thread.
3
2
4
5
1
NOTE: You may want to cut the end of the thread with scissors for easier
needle threading. Switch the power on after threading the machine and
bobbin. You are now ready to sew.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
