Yetter 2995 XFC Manual de usuario

2995 XFC Fertilizer Coulter

2995 XCC Cutting Coulter

OPERATORS MANUAL

WITH PARTS IDENTIFICATION

2565-788_REV_B ●11/2018

YETTER MANUFACTURING CO.

FOUNDED 1930

Colchester, IL 62326-0358

Toll free: 800/447-5777

309/776-3222 (Fax)

Website: www.yetterco.com

E-mail: info@yetterco.com

FOREWORD

You’ve just joined an exclusive but rapidly

growing club.

For our part, we want to welcome you to the

group and thank you for buying a Yetter product.

We hope your new Yetter products will help you

achieve both goals-increase your productivity and

increase your efficiency so that you may generate

more profit.

This operator’s manual has been designed into

four major sections: Foreword, Safety

Precautions, Installation Instructions and Parts

Breakdown.

This SAFETY ALERT SYMBOL indicates

important safety messages in the manual.

When you see this symbol, be alert to the

possibility of PERSONAL INJURY and

carefully read the message that follows.

The word NOTE is used to convey information

that is out of context with the manual text. It

contains special information such as

specifications, techniques and reference

information of a supplementary nature.

The word IMPORTANT is used in the text when

immediate damage will occur to the machine due

to improper technique or operation. Important will

apply to the same information as specified by

note only of an immediate and urgent nature.

It is the responsibility of the user to read the

operator’s manual and comply with the safe and

correct operating procedure and to lubricate and

maintain the product according to the

maintenance schedule in the operator’s manual.

The user is responsible for inspecting his

machine and for having parts repaired or

replaced when continued use of the product

would cause damage or excessive wear to the

other parts.

It is the user’s responsibility to deliver his

machine to the Yetter dealer who sold him the

product for service or replacement of defective

parts, which are covered by the warranty policy.

If you are unable to understand or follow the

instructions provided in this publication, consult

your local Yetter dealer or contact:

YETTER MANUFACTURING CO.

309/776-4111

800/447-5777

309/776-3222 (FAX)

Website: www.yetterco.com

E-mail: info@yetterco.com

WARRANTY

Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This

warranty being expressly limited to replacement at the factory of such parts or products as shall appear to

be defective after inspection. This warranty does not obligate the Company to bear cost of labor in

replacement of parts. It is the policy of the Company to make improvements without incurring obligations to

add them to any unit already sold. No warranty is made or authorized to be made, other than herein set

forth. This warranty is in effect for one year after purchase.

Dealer ___________________________________________________

Yetter Manufacturing warrants its own products only and cannot be responsible for damages to

equipment on which mounted.

SAFETY

A brief description of signal words that may be used in this manual:

CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe

practices.

WARNING: Denotes a specific potential hazard.

DANGER: Denotes the most serious specific potential hazard.

SAFETY PRECAUTIONS

You can make your farm a safer place to live and work if you observe the safety precautions given. Study

these precautions carefully and insist that they be followed by those working with you and for you.

Finally, remember this: an accident is usually caused by someone’s carelessness, neglect, or oversight.

WARNING

Never clean, lubricate or adjust a machine that is in motion. Always lower or block the implement before

performing service.

If machine must be serviced in the raised position, jack or block it up to prevent it from accidentally falling

and injuring someone.

Do not allow riders on the tractor or implement.

Use speeds and caution dictated by the terrain being traversed. Do not operate on any slope steep enough

to cause tipping or loss of control.

Be sure all personnel are clear of the immediate area before operating.

Read and understand the operator’s manual and require all other persons who will operate the equipment

to do the same.

Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in

an emergency.

CAUTION

Consult your implement and tractor operator’s manual for correct and safe operating practices.

Beware of towed implement width and allow safe clearance.

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH.

GENERAL INFORMATION

MAINTENANCE

•

After a few hours use, check all bolts and setscrews for tightness.

•

After using a few hours, check for loose hardware, re-tighten as needed.

•

After a few days use, check coulter hubs for loose bearings. There should be no end play in the hub

bearings to allow it to wobble. If necessary, remove hub cap and cotter pin, adjust slotted nut to remove

wobble, re-insert cotter pin and replace hub cap.

LUBRICATION

DANGER: Always install safety lock-ups or lower the planter to the ground before working on the machine.

Lubricate at frequency indicated with a multi-purpose type grease.

ISO 2995-086

DANGER: Always install all safety lock-ups and safety lock pins before working under the toolbar.

1. Raise the toolbar until is clear off the ground. Remove the gauge wheel and the blade. Remove the hubcap,

cotter pin, slotted nut and washer from the spindle shaft assembly.

2. Pull the coulter spindle shaft assembly from the hub. Remove bearing cones and cups and discard if bearings

are being replaced. Clean hub and dry. Remove bearings only and not cups of re-packing.

3. Wash the old grease from the hub, bearing cups, coulter spindle shaft, seal, and bearing cones. Inspect the

condition of bearing cups and cones.

4. Apply #2 multi-purpose lithium grease on each bearing. Make sure the space around each roller is filled.

Lubricate the bearing cups.

5. Position the bearing in the cup and install the seal. Lubricate the seal lips and proceed with re-assembly of the

removed parts including the blade. Blade bolt torque is 90 to 96 ft. lbs.

6. Install outer bearing, washer, and slotted nut. Tighten the slotted nut to 150 in. lbs. while rotating the blade or

until a definite drag is felt when the blade is turned by hand. Tighten the nut one slot position to line up the

cotter pin hole with a slot. Secure the nut with a new cotter pin.

ASSEMBLY INSTRUCTIONS

STEP 1. Install shank to the coulter assembly.

ASSEMBLY INSTRUCTIONS

STEP 2. Install roll pin to the shank.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Maquinaria agrícola de Yetter

Yetter

Yetter 5000 SERIES Manual de usuario

Yetter

Yetter 2967-035A Manual de usuario

Yetter

Yetter NARROW ROW Manual de usuario

Yetter

Yetter 2962-003A Manual de usuario

Yetter

Yetter 2967-006A Manual de usuario

Yetter

Yetter 5000 SERIES Manual de usuario

Yetter

Yetter 2966-020A Manual de usuario

Yetter

Yetter Nutrient Pro 4000 Series Manual de usuario

Yetter

Yetter 2968-050 Manual de usuario

Yetter

Yetter 2565-980 Manual de usuario

Yetter

Yetter 5000-023A Manual de usuario

Yetter

Yetter TITAN Series Manual de usuario

Yetter

Yetter 2968-020B Manual de usuario

Yetter

Yetter Furrow Max 6200-070 Manual de usuario

Yetter

Yetter 3400 Series Manual de usuario

Yetter

Yetter SHORT U.N.T. 2967-029B Manual de usuario

Yetter

Yetter 5000 SERIES Manual de usuario

Yetter

Yetter Systems One Seed Jet II Manual de usuario

Yetter

Yetter 2920-012 Manual de usuario

Yetter

Yetter 2967-002B Manual de usuario

Yetter

Yetter TITAN 2967-033A Manual de usuario

Yetter

Yetter TITAN Series Manual de usuario

Yetter

Yetter 5000-022 Lexion C512-30/Capello Manual de usuario

Yetter

Yetter CAB CONTROL STRIP FRESHENER 2984-050A Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario