Yeastar Technology S-Series Manual de usuario
Yeastar S-Series VoIP PBX
Installation Guide
Installation_Guide
1.0
December 4, 2019
Contents
Installation Guide...................................................................................................................................................... 3
Hardware Overview..............................................................................................................................................3
S412 Overview..............................................................................................................................................3
S20 Overview................................................................................................................................................5
S50 Overview................................................................................................................................................8
S100 Overview............................................................................................................................................10
S300 Overview............................................................................................................................................12
Expansion Board.........................................................................................................................................15
Install PBX..........................................................................................................................................................16
Installation Warnings...................................................................................................................................16
Package Contents.......................................................................................................................................16
Install Yeastar S20......................................................................................................................................17
Install Yeastar S50......................................................................................................................................20
Install Yeastar S100....................................................................................................................................24
Install Yeastar S300....................................................................................................................................30
Install Yeastar S412....................................................................................................................................36
Connect Your PBX.............................................................................................................................................38
Installation Guide
Installation Guide for Yeastar S-Series VoIP PBX.
About this guide
This guide describes hardware ports and indicators on the Yeastar S-Series VoIP PBX, and give instructions on how
to install the PBX and telephony modules.
Hardware Overview
S412 Overview
Front Panel
Table 1: Descriptions of S412 Front Panel
LED Indication Status Description
On The power is switched on.POWER Power status
Off The power is switched off.
Blinking The system is running properly.SYSTEM System status
Static/Off The system goes wrong.
Static Linked normally.
Blinking In communication.
WAN WAN status
Off Off-line.
Static Linked normally.
Blinking In communication.
LAN LAN status
Off Off-line.
Installation_Guide | 1 - Installation Guide | 4
LED Indication Status Description
Red: static The GSM/3G/4G Trunk is idle.
Red: blinking slowly No SIM card.
GSM/3G/4G
Red: blinking rapidly The GSM/3G/4G trunk is in use.
Orange: blinking The BRI line is disconnected.BRI
Orange: static The BRI line is connected or in use.
Red: static The PSTN line is idle.
Red: blinking slowly No PSTN line is connected to the
FXO port.
1-4
(Line status)
FXO
Red: blinking rapidly The PSTN line is busy.
Green: static The analog phone is idle.1-12
(FXS port)
FXS
Green: blinking The analog phone is busy.
Rear Panel
Installation_Guide | 1 - Installation Guide | 5
Table 2: Descriptions of S412 Rear Panel
Port Description
RJ11
(Line port)
•FXO port (red light): For the connection of PSTN lines or FXS ports of
traditional PBX.
•BRI port (orange light): For the connection of ISDN BRI lines.
Note: The sequence number of the ports corresponds to that of the
Indicator lights in the front panel. (I.e. the LED lights in the front indicate the
connection status of the corresponding ports at the back panel.)
RJ11
(FXS port)
•FXS port (green light): For the connection of analog phones.
Note: The sequence number of the ports corresponds to that of the
Indicator lights in the front panel. (I.e. the LED lights in the front indicate the
connection status of the corresponding ports at the back panel.)
WAN/LAN Yeastar S412 provides two 10/100Mbps adaptive RJ45 Ethernet ports, and supports
3 Ethernet modes. The default mode is “Single”.
•Single: LAN port will be used for uplink connection. WAN port is disabled.
•Bridge: LAN port will be used for uplink connection. WAN port will be used as
bridge for PC connection.
•Dual: Both LAN and WAN ports can be used for uplink connection.
TF Slot Insert TF card to store auto recording files.
Reset Button Press and hold for 10 seconds to restore the factory defaults.
Power Inlet Connect the supplied power supply to the port.
S20 Overview
Front Panel
Installation_Guide | 1 - Installation Guide | 6
Table 3: Descriptions of S20 Front Panel
LED Indication Status Description
On The power is switched on.POWER Power
status Off The power is switched off.
Blinking The system is running properly.SYSTEM System
status Static/Off The system goes wrong.
Static Linked normally.
Blinking In communication.
WAN WAN
status
Off Off-line.
Static Linked normally.
Blinking In communication.
LAN LAN
status
Off Off-line.
Green: static The analog phone is idle.FXS
Green: blinking The analog phone is busy.
Red: static The GSM/3G/4G Trunk is idle.
Red: blinking slowly No SIM card.
GSM/3G/4G
Red: blinking rapidly The GSM/3G/4G trunk is in use.
Orange: blinking The BRI line is disconnected.BRI
Orange: static The BRI line is connected or in use.
Red: static The PSTN line is idle.
1-4
(Telephony
ports)
FXO
Red: blinking slowly No PSTN line is connected to the FXO port.
Installation_Guide | 1 - Installation Guide | 7
LED Indication Status Description
Red: blinking rapidly The PSTN line is busy.
Rear Panel
Table 4: Descriptions of S20 Rear Panel
Port Description
RJ11 •FXO port (red light): For the connection of PSTN lines or FXS ports of
traditional PBX.
•FXS port (green light): For the connection of analog phones.
•BRI port (orange light): For the connection of ISDN BRI lines.
Note: The sequence number of the ports corresponds to that of the
Indicator lights in the front panel. (I.e. the LED lights in the front indicate the
connection status of the corresponding ports at the back panel.)
WAN/LAN Yeastar S20 provides two 10/100Mbps adaptive RJ45 Ethernet ports, and supports
3 Ethernet modes. The default mode is “Single”.
•Single: LAN port will be used for uplink connection. WAN port is disabled.
•Bridge: LAN port will be used for uplink connection. WAN port will be used as
bridge for PC connection.
•Dual: Both LAN and WAN ports can be used for uplink connection.
TF Slot Insert TF card to store auto recording files.
Antenna
Socket
Rotate the antenna into the Antenna Socket.
Reset Button Press and hold for 10 seconds to restore the factory defaults.
Power Inlet Connect the supplied power supply to the port.
Installation_Guide | 1 - Installation Guide | 8
S50 Overview
Front Panel
Table 5: Descriptions of S50 Front Panel
LED Indication Status Description
On The power is switched on.POWER Power status
Off The power is switched off.
Blinking The system is running properly.SYSTEM System status
Static/Off The system goes wrong.
Green: static The analog phone is idle.FXS
Green: blinking The analog phone is busy.
Red: static The GSM/3G/4G Trunk is idle.
Red: blinking
slowly
No SIM card.
GSM/3G/4G
Red: blinking
rapidly
The GSM/3G/4G trunk is in use.
Orange: blinking The BRI line is disconnected.BRI
Orange: static The BRI line is connected or in use.
Red: static The PSTN line is idle.
1-8 LED
(RJ11 port
status)
FXO
Red: blinking
slowly
No PSTN line is connected to the FXO port.
Installation_Guide | 1 - Installation Guide | 9
LED Indication Status Description
Red: blinking
rapidly
The PSTN line is busy.
Port Description
WAN/LAN Yeastar S50 provides two 10/100/1000Mbps adaptive RJ45 Ethernet ports, and
supports 3 Ethernet modes. The default mode is “Single”.
•Single: LAN port will be used for uplink connection. WAN port is disabled.
•Bridge: LAN port will be used for uplink connection. WAN port will be used as
bridge for PC connection.
•Dual: Both LAN and WAN ports can be used for uplink connection.
SD Insert SD card to store auto recording files.
1-8 Port
(RJ11 port)
•FXO port(red light): For the connection of PSTN lines or FXS ports of traditional
PBX.
•FXS port (green light): For the connection of analog phones.
•BRI port (orange light): For the connection of ISDN BRI lines.
Note: The sequence number of the ports corresponds to that of the
Indicator lights in the front panel. (I.e. the LED lights in the front indicate the
connection status of the corresponding ports at the back panel.)
Reset button Press and hold for 10 seconds to restore the factory defaults.
Rear Panel
Table 6: Descriptions of S50 Rear Panel
Port Description
Antenna
Socket
Rotate the antenna into the Antenna Socket.
Power Switch Press this button to switch on/off the device.
Installation_Guide | 1 - Installation Guide | 10
Port Description
Power Inlet Connect the supplied power supply to the port.
Protective
Earth
Connect to the ground to reduce the risk of electrocution to the user or protect the
PBX from the bad effects of external noise in the case of a lightning strike.
S100 Overview
Front Panel (1*EX30 + 1*EX08)
Table 7: Descriptions of S100 Front Panel
Port Description
E1/T1 Connect the E1/T1 line.
1-8 Port
(RJ11 port)
•FXO port (red light): For the connection of PSTN lines or FXS ports of
traditional PBX.
•FXS port (green light): For the connection of analog phones.
•BRI port (orange light): For the connection of ISDN BRI lines.
Note: The sequence number of the ports corresponds to that of the
Indicator lights in the front panel. (I.e. the LED lights in the front indicate the
connection status of the corresponding ports at the back panel.)
LED Indication Status Description
Green: static The analog phone is idle.FXS
Green: blinking The analog phone is busy.
Red: static The GSM/3G/4G Trunk is idle.
Red: blinking slowly No SIM card.
1-8
(RJ11 port
status)
GSM/3G/4G
Red: blinking rapidly The GSM/3G/4G trunk is in use.
Otros manuales para S-Series
3
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Teléfono de Yeastar Technology
