Yamaha Reface CS Manual de usuario

reface CS / reface DX / reface CP / reface YC V1.30 Updater Guide 1

Thank you for choosing a reface series product.

This Updater Guide describes how to update your reface CS / reface DX / reface CP / reface

YC to version 1.30 and the update’s main enhancements.

Please read this document carefully before updating your reface.

Notes

• This updater is designed for use with the reface CS / reface DX / reface CP / reface YC only.

• When the reface CP or reface YC is updated, all settings including keyboard settings are returned to their factory defaults.

• This updater is to be used at the user’s own risk.

• A computer running one of the following operating systems is required for this update:

Microsoft Windows 7 (32-bit or 64-bit); Windows 8.1 (32-bit or 64-bit); Windows 10 (32-bit or 64-bit)

Mac OSX 10.9; Mac OSX 10.10; Mac OSX 10.11

• The update will take approximately five minutes. Please ensure that your computer does not enter Sleep mode during this

time.

• During the update, do not launch or operate any applications other than the updater on your computer.

• During the update, be sure to power the reface by using its AC adaptor.

• If your reface should fail to function as a result of the supply of power being interrupted or incorrect operation during the

update, repeating the update procedure from the beginning may not resolve the problem.

• If your reface fails to function after repeating the update procedure from the beginning, please contact your nearest

Yamaha service center.

Applicable models

reface CS / reface DX / reface CP / reface YC, ealier than version 1.30

V1.30 Updater Guide

reface CS / reface DX / reface CP / reface YC V1.30 Updater Guide 2

Confirming the Current Version

reface CS

Operation

While holding down the D#2 key, press the [ ] (Standby/On) switch.

Confirm

If the LOOPER slider’s REC lamp lights up or flashes, your reface already has firmware version 1.30 or later and does

not need to be updated. Therefore, you do not need to use this updater. If the lamps neither light up nor flash, proceed

with updating as described in “Updating Procedure.”

reface DX

Operation

While holding down the F#3, A3, and C#4 keys, press the [ ] (Standby/On) switch.

Confirm

If the version shown on the display is 1.30 or later, you do not need to use this updater. If the version shown is earlier than

1.30, proceed with updating as described in “Updating Procedure.”

Confirm version

D#2

Confirm version

F#3C#4A3

reface CS / reface DX / reface CP / reface YC V1.30 Updater Guide 3

reface CP

Operation

While holding down the C#2 key, press the [ ] (Standby/On) switch.

Confirmation

If the [TYPE] knob’s Wr lamp and Clv lamp light up or flash, your reface already has firmware version 1.30 and does not

need to be updated. If the lamps neither light up nor flash, proceed with updating as described in “Updating Procedure.”

reface YC

Operation

While holding down the C#2 key, press the [ ] (Standby/On) switch.

Confirmation

If the [WAVE] knob’s H lamp lights up or flashes, your reface already has firmware version 1.30 and does not need to be

updated. If the lamp neither lights up nor flashes, proceed with updating as described in “Updating Procedure.”

Confirm version

C#2

Confirm version

C#2

reface CS / reface DX / reface CP / reface YC V1.30 Updater Guide 4

Updating Procedure

1. Press the [ ] (Standby/On) switch and turn off the reface.

Ensure that the AC power adaptor is connected to the reface.

2. Connect your reface to the computer by using a USB cable.

3. While holding down the F#3, A3, and C#4 keys, press the [ ] (Standby/On) switch and turn the reface back on.

4. Confirm that the reface starts up in Update mode.

reface CS

The [ ] (Multi-saw) lamp from the OSC (Oscillator) section lights up.

reface DX

The message “reface DX Update” is shown on the display.

reface CP

The [TYPE] knob’s Rdl lamp lights up.

reface YC

The [WAVE] knob’s Y lamp lights up.

Confirm version

F#3C#4A3

reface CS / reface DX / reface CP / reface YC V1.30 Updater Guide 5

5. Launch the “reface updater” application on your computer.

Windows

Mac

6. Set “MIDI Port” on the application to “reface.”

NOTICE

The application’s progress bar shows how much data has been transferred. The update process will con-

tinue for a certain time after the transfer has finished. Be sure to confirm completion of the update process

on the reface itself.

NOTICE

The application’s progress bar shows how much data has been transferred. The update process will con-

tinue for a certain time after the transfer has finished. Be sure to confirm completion of the update process

on the reface itself.

Step 6

Step 7

Step 6

Step 7

reface CS / reface DX / reface CP / reface YC V1.30 Updater Guide 6

7. Click the [Start] button on the application.

Confirm that the update has started based on the following display.

reface CS

As the update progresses, the OSC (Oscillator) lamps light up successively from bottom to top.

reface DX

As the update progresses, the display successively shows the messages “LOADING”, “ERASING”, WRITING”, and

“Completed.”

reface CP

As the update progresses, the [TYPE] knob’s lamps light up sequentially starting with Rdl.

reface CS / reface DX / reface CP / reface YC V1.30 Updater Guide 7

reface YC

As the update progresses, the [WAVE] knob’s lamps light up sequentially starting with Y.

8. Confirm that the reface indicates the update as being complete.

reface CS

All of the lamps from the OSC (Oscillator) section and the LOOPER section’s REC and PLAY lamps light up.

reface DX

The message “Completed” is shown on the display.

reface CP

All of the [TYPE] knob’s lamps light up.

reface YC

All of the [WAVE] knob’s lamps light up.

9. Shut down the updater application on the computer.

10. Restart your reface as described in “Confirming the Current Version” and confirm that it has been updated to version

1.30.

This completes the update process.

reface CS / reface DX / reface CP / reface YC V1.30 Updater Guide 8

Main Enhancements

[V1.20 V1.30]

Additional features and specifications changes

reface CS

• It is now possible to set the master tuning, master transpose, pitch bend range, transmit channel, and receive channel.

• A click sound has been added to the Phrase Looper.

• Sustain can now be applied using an FC3 foot pedal or an FC4 or FC5 foot switch.

reface DX

• A Tuning screen has been added as Page 2 displayed by using the [FUNCTION] button. On this page, you can set the

master tuning and master transpose.

• A click sound has been added to the Phrase Looper.

[V1.00 V1.30]

Additional features and specifications changes

reface CP

• It is now possible to set the master tuning, master transpose, transmit channel, and receive channel.

reface YC

• It is now possible to set the master tuning, master transpose, transmit channel, and receive channel.

• When the rotary speed is FAST, you can now also switch to SLOW by moving the [ROTARY SPEED] lever up once.

[V1.01 V1.20]

Additional features and specifications changes

reface CS

• The pitch bend range can now be switched between “12” (1 octave) and “2” (2 semitones).

• The LOOPER can now quantize at either sixteenth notes or eighth-note triplets.

reface DX

• The LOOPER can now quantize at either sixteenth notes or eighth-note triplets.

Manual Development Department

Published 03/2016 PO-B0

Otros manuales para Reface CS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sintetizador de Yamaha

Yamaha

Yamaha Symphonic Ensemble SK10 Manual de usuario

Yamaha

Yamaha Loopfactory DX200 Manual de usuario

Yamaha

Yamaha P-200 Manual de usuario

Yamaha

Yamaha Clavinova CVP-98/CVP-96 Manual de usuario

Yamaha

Yamaha PSR-S550 Manual de usuario

Yamaha

Yamaha LC3 Music lab Manual de usuario

Yamaha

Yamaha MM6 Manual de usuario

Yamaha

Yamaha pf50 Manual de usuario

Yamaha

Yamaha EOS B700 Manual de usuario

Yamaha

Yamaha DX21 Guía de inicio rápido

Yamaha

Yamaha DX100 Manual de usuario

Yamaha

Yamaha YS200 Manual de usuario

Yamaha

Yamaha DX21 Manual de usuario

Yamaha

Yamaha S70 XS Manual de usuario

Yamaha

Yamaha CE20 Manual de usuario

Yamaha

Yamaha PF2000 Manual de usuario

Yamaha

Yamaha MOX8 Manual de usuario

Yamaha

Yamaha DX7II-FD/D Manual de usuario

Yamaha

Yamaha DX100 Manual de usuario

Yamaha

Yamaha Strings SS-30 Manual de usuario

Yamaha

Yamaha DX7 II FD Manual del propietario

Yamaha

Yamaha P-120 Manual de usuario

Yamaha

Yamaha YPP-15 Instrucciones de montaje

Yamaha

Yamaha PF2000 Manual de usuario

Manuales populares de Sintetizador de otras marcas

Kawai

Kawai MP7 Manual técnico

Joranalogue

Joranalogue Contour 1 Manual de usuario

Full Bucket Music

Full Bucket Music Mono/Fury Manual de usuario

Kawai

Kawai PH50 Manual de usuario

IK Multimedia

IK Multimedia UNO Synth PRO X Manual de usuario

Behringer

Behringer DEEPMIND 12 Manual de usuario

Roland

Roland Gaia SH-01 Manual de usuario

Roland

Roland GR-30 Manual de usuario

Gotharman

Gotharman Gotharman's anAmoNo-box Manual de usuario

QuStream

QuStream HDFS-550 Manual de usuario

Modal Electronics

Modal Electronics ARGON8 Manual de usuario

Roland

Roland GS-500 Manual de usuario

Octave

Octave Cat SRM Manual de usuario

Dreadbox

Dreadbox Murmux Initiate Manual de usuario

neutral labs

neutral labs ELMYRA 2 Manual de usuario

Waldorf

Waldorf KYRA Manual de usuario

Tubbutec

Tubbutec Juno-66 Manual de usuario

EFM

EFM VCADSR - 3510 Manual de usuario