Yamaha YSP-3300 Manual de uso y cuidado

Firmware Update Procedure for YSP-3300/YSP-4300

Page.1 of 7

< IMPORTANT NOTICE >

Do not attempt to update your Yamaha Sound Projector using any other data file except those

provided directly from the Yamaha website.

Follow the instructions carefully and do not attempt any other procedures not specified in the

instructions provided by Yamaha. Improperly updated products may cause improper operation, and

any parts or service required to restore proper operation will not be covered under the Yamaha

Limited Warranty.

Choose your product:

Update Procedure for YSP-3300……………from Page 2

Update Procedure for YSP-4300…………from Page 5

If an error occurs, see Troubleshooting section on the last page.

Firmware Update Procedure for YSP-3300/YSP-4300

Page.2 of 7

Update Procedure for YSP-3300

Requirements:

A computer capable of burning an audio CD

Software file provided by YAMAHA,” YSP12_xxxx.wav”

BD/DVD/CD player* with optical or coaxial digital audio connection

*Note) CD PLAYER IS PREFERRED.

Some DVD players use digital filters, which affects the output signal of the devices. This firmware

update may not work with DVD players which use these digital filters. CD player usually does not

use these filters.

CHECK THE FIRMWARE VERSION PRIOR TO THIS UPDATE

Confirm that the power of YSP is off. Press and hold the [INPUT] key on the YSP and

while holding that key, power on (press [ ] from the remote controller/ [ ] on the

YSP). “ADVANCED SETUP” will appear on the front display. Then, press [UP]/[DOWN]

key to display “FW UPDATE”. After pressing [ENTER] or [RIGHT] key on the remote

controller, current version will be shown on the front display.

There are 2 different firmware prepared for the best your YSP performance.

1. YSP12_0019.wav

Use this firmware, if current firmware version is 09.XX.XX*or less (08, 07, ...).

New firmware version will be 12.04.05 after the update.

2. YSP12_0017.wav

Use this firmware, if current firmware version is 10.XX.XX*.

New firmware version will be 11.04.05 after the update.

(*XX.XX may have several variations)

If you are not able to perform the update, please make arrangements to deliver the unit to

an Authorized Yamaha Service Center and they will perform the update.

The following pages contain the procedures for this firmware update.

STEP1 CREATE UPDATE DISC

Download the firmware from Yamaha website. Unzip the downloaded file

“YSP3300_Vxxxxx.zip”. The update file “YSP12_xxxx.wav” will appear. Burn

the WAV file onto CD-R/RW as an Audio-CD. This will be your update disc.

If you need instructions on creating this firmware update CD, see your Personal

Computer ("PC") CD burning software instructions on how to burn WAV file as an

Audio CD.

Note:

Conventional CD burning software is

recommended. An audio CD burned by

Windows Media Player may not work.

Firmware Update Procedure for YSP-3300/YSP-4300

Page.3 of 7

STEP2 CONNECT DIGITAL AUDIO WITH BD/DVD/CD PLAYER

Power off the YSP and BD/DVD/CD player. Then, connect the CD, DVD or BD

player* to your YSP using either optical or coaxial digital cable.

*It is recommended to remove all other connection from the player. If the player is

connected to another amplifier/receiver, make sure those components are powered off. Or

else, the loud digital communication sound output during the update could cause damage

to the speakers.

STEP3 ENTER FIRMWARE UPDATE MODE

Confirm that the power of YSP is off. Press and hold the [INPUT] key on the YSP

and while holding that key, power on. “ADVANCED SETUP” will appear on the

front display. Then, press [UP]/[DOWN] key to display “FW UPDATE”. After

pressing [ENTER] or [RIGHT] key on the remote controller, current version will

be shown on the front display.

STEP4 Press [UP]/[DOWN] key on the remote controller, “START OK?” appears on the

YSP’s front display. Afterwards, press [ENTER] key, “PLAY CDDA!” will appear.

Now your YSP is ready for firmware update.

YSP (Rear Side)

BD/DVD/CD Player*

Optical Digital Audio Cable

Coaxial Digital Audio Cable

Optical

Coaxial

DIGITAL IN DIGITAL OUT

INPUT

IR Sensor

Firmware Update Procedure for YSP-3300/YSP-4300

Page.4 of 7

Note:

Executing this update will RESET the YSP’s setting, including the AUTO SETUP

(IntelliBeam) to factory default.

STEP5 START FIRMWARE UPDATE

Power on the BD/DVD/CD player. Load and play the Firmware Update CD (Audio

CD) on the BD/DVD/CD player. “Found Head” will appear on the YSP’s front

display for few seconds. Then, the firmware update starts. Rapidly changing

numbers are displayed during the update.

“Found Head” appears within 10 seconds from starting update disc playback. In case display

doesn’t change after 10 seconds, power off and retry the update process again from the

beginning or check requirements for the update disc and connection. See Troubleshooting for

details.

While update is in progress, DO NOT interrupt the YSP by pressing any keys

or switching off the power.

When completed, “Success”, “Please...” and “Power off!” are displayed

repeatedly. Press the [ ]key on the YSP to turn off the power.

Stop the BD/DVD/CD player, remove update disc and power off.

STEP6 CONFIRM UPDATED VERSION

Press and hold the [INPUT] key and power on. “ADVANCED SETUP” will

appear on the front display. Then, press [UP]/[DOWN] keys to display “FW

UPDATE”. After pressing [ENTER] or [RIGHT] key on the remote controller,

current version will be shown on the front display.

If the version number doesn’t match, retry the update procedure again from the beginning or

check requirements for the update disc and connection.

See Troubleshooting for details.

To exit, power off.

Your YSP is now ready for normal use.

Perform AUTO SETUP and optimize the sound beam adjustments. (Refer to the

AUTO SETUP (Intellibeam) section on the owner’s manual for details)

Firmware Update Procedure for YSP-3300/YSP-4300

Page.5 of 7

Update Procedure for YSP-4300

Requirements:

USB thumb drive (File system with FAT16 or FAT32 format)

Software file provided by YAMAHA,”YSP2012-xxxx.bin”.

CHECK THE FIRMWARE VERSION PRIOR TO THIS UPDATE

Confirm that the power of YSP is off. Press and hold the [INPUT] key on the YSP and

while holding that key, power on (press [ ] from the remote controller/ [ ] on the

YSP). “ADVANCED SETUP” will appear on the front display. Then, press [UP]/[DOWN]

key to display “FW UPDATE”. After pressing [ENTER] or [RIGHT] key on the remote

controller, current version will be shown on the front display. If the firmware version is

already up-to-date, it is not perform the update.

There are 2 different firmware prepared for the best your YSP performance.

1. YSP2012-0020.bin

Use this firmware, if current firmware version is 09.XX.XX*or less (08, 07, ...).

New firmware version will be 12.04.05 after the update.

2. YSP2012-0018.bin

Use this firmware, if current firmware version is 10.XX.XX*.

New firmware version will be 11.04.05 after the update.

(*XX.XX may have several variations)

If you are not able to perform the update, please make arrangements to deliver the unit to

an Authorized Yamaha Service Center and they will perform the update.

The following pages contain the procedures for this firmware update.

STEP 1 Copy the update file to a USB thumb drive

Unzip the downloaded file “YSP4300_Vxxxxx.zip”. The update file

“YSP2012-xxxx.bin” will appear. Copy to the root directory of a USB thumb

drive that supports USB mass storage class. (It is recommended to delete all

other files or folders.)

STEP 2 Insert the USB thumb drive

Firmware Update Procedure for YSP-3300/YSP-4300

Page.6 of 7

STEP3 ENTER FIRMWARE UPDATE MODE

Confirm that the power of YSP is off. Press and hold the [INPUT] key on the

YSP and while holding that key, power on. “ADVANCED SETUP” will appear

on the front display. Then, press [UP]/[DOWN] key to display “FW UPDATE”.

After pressing [ENTER] or [RIGHT] key on the remote controller, current

version will be shown on the front display.

STEP4 Press [UP]/[DOWN] key on the remote controller, “START OK?” appears on the

YSP’s front display.

Note:

Executing this update will RESET the YSP’s setting, including the AUTO

SETUP (IntelliBeam) and radio station preset setting to factory default.

STEP5 START FIRMWARE UPDATE

Press [ENTER] key, “USB Update”, “Connect!” will be shown on the display

and the USB update will automatically start. During the update, “Update xx%” is

showing the progress.

In case display doesn’t change, power off and retry the update process again from the beginning

or check requirements. See Troubleshooting for details.

While update is in progress, DO NOT interrupt the YSP by pressing any keys

or switching off the power.

When completed, “Success”, “Please...” and “Power off!” are displayed

repeatedly. Press the [ ]key on the YSP to turn off the power.

Disconnect USB thumb drive from the YSP.

STEP6 CONFIRM UPDATED VERSION

Press and hold the [INPUT] key and power on. “ADVANCED SETUP” will

appear on the front display. Then, press [UP]/[DOWN] keys to display “FW

UPDATE”. After pressing [ENTER] or [RIGHT] key on the remote controller,

current version will be shown on the front display. To exit, power off.

If the version number doesn’t match, retry the update procedure again from the beginning or

check requirements. See Troubleshooting for details.

Your YSP is now ready for normal use.

Perform AUTO SETUP and optimize the sound beam adjustments. (Refer to the

AUTO SETUP (Intellibeam) section on the owner’s manual for details)

INPUT

IR Sensor

Firmware Update Procedure for YSP-3300/YSP-4300

Page.7 of 7

Troubleshooting

Case1 Update did not start after playing the update disc on the BD/DVD/CD player.

(YSP-3300)

Check digital cable wiring. Only optical or coaxial connection can be used for

this update. HDMI connection will not work.

Check digital out setting. When using DVD/BD players, make sure the digital out

is set to “PCM”.

Check update disc. Make sure that your CD-R/RW is finalized and created as

an “AUDIO CD”. (playable on any CD player)

If all above are cleared and still having problems, your BD/DVD/CD player may not

be suited for this update. Try another BD/DVD/CD player or contact your local

authorized service center to update the YSP for you.

Case2 YSP cannot verify the update file in the USB thumb drive. (YSP-4300)

Check that the update file is located in the root directory of the USB thumb

drive.

Check that no other folders are created in the USB thumb drive.

Make sure that the USB thumb drive is not password protected.

(Cannot read files from a security protected USB thumb drive)

Make sure the file name of the update data has not been renamed.

Try using another USB thumb drive.

Case3 After the update, YSP doesn’t power on or doesn’t operate correctly with the

remote controller.

Unplug the AC cable from wall outlet and plug again. If the YSP still doesn’t

operate correctly, try “Case4”.

Case4 YSP doesn’t power on at all after the update.

Perform the following alternative update method to recover.

PL1. Unplug the AC cable from the wall outlet.

PL2. Press and hold [VOLUME +] key. While holding the [VOLUME +] key, plug

the AC cable to the wall outlet. “PLAY CDDA!” (YSP-3300)/”USB Update”

(YSP-4300) will appear on the front display.

PL3. Repeat from STEP 5.

VOLUME +

Otros manuales para YSP-3300

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de altavoces de Yamaha

Yamaha

Yamaha VXL1B-24 Manual de usuario

Yamaha

Yamaha NS-BP182 Manual de usuario

Yamaha

Yamaha IF2112/64(W) Manual de usuario

Yamaha

Yamaha NS-515F Manual de usuario

Yamaha

Yamaha NS-2HX Manual de usuario

Yamaha

Yamaha NS-90 Manual de usuario

Yamaha

Yamaha DBR Series Manual de usuario

Yamaha

Yamaha IF2115/AS Manual de usuario

Yamaha

Yamaha ATS-1050 Manual de usuario

Yamaha

Yamaha VXC2FB Manual de usuario

Yamaha

Yamaha DSP-E200 Manual de usuario

Yamaha

Yamaha NS-10MC Manual de usuario

Yamaha

Yamaha NS-B20 Manual de usuario

Yamaha

Yamaha YHT-18 Instrucciones de montaje

Yamaha

Yamaha NS-M325 Manual de usuario

Yamaha

Yamaha YHT-17 Instrucciones de montaje

Yamaha

Yamaha R112 Manual de usuario

Yamaha

Yamaha YHT-33 Instrucciones de montaje

Yamaha

Yamaha YAS-203 Manual de usuario

Yamaha

Yamaha YHT-31 Instrucciones de montaje

Yamaha

Yamaha YRS-2100 Manual de instrucciones

Yamaha

Yamaha NS-C225 - Center CH Speaker Manual de usuario

Yamaha

Yamaha YAS-209 Manual de usuario

Yamaha

Yamaha YSP-5600 Manual de uso y cuidado

Manuales populares de Sistema de altavoces de otras marcas

JVC

JVC CA-MXK5R Manual de usuario

LG NB4532B Manual de usuario

JVC

JVC CA-FSH100 Manual de usuario

5Core

5Core Pro Series Manual de usuario

EAW

EAW MQV1394e Manual de usuario

Lynx

Lynx GXR-LA10A Manual de usuario

iLive

iLive ITB066B Manual de usuario

RDX

RDX QuickStation 4 Manual de usuario

Electro-Voice

Electro-Voice S-122 Manual de usuario

Sven

Sven SPS-619 GOLD Manual de usuario

Pioneer

Pioneer CS-7070 Manual de usuario

EAW

EAW UB82e Manual de usuario

Sondpex

Sondpex Active Speaker System and Digital Music... Manual de usuario

JVC

JVC NX-PN7 Manual de usuario

Marshall Amplification

Marshall Amplification AR-DM61-BT Manual de usuario

SE Audiotechnik

SE Audiotechnik I-LINE Manual de usuario

Gemini

Gemini WRX-843 Series Manual de usuario

TCL

TCL 6100 Series Manual de usuario