Yamaha WARRIOR YFM350XP Manual
YFM350XP
SUPPLEMENTARY
SERVICE MANUAL
LIT-11616-15-09 3GD-28197-16
FOREWORD
This Supplementary Service Manual has been prepared to introduce new service and new data for
the YFM350XP. For complete information on service procedures, it is necessary to use this Supple-
mentary Service Manual together with the following manual.
YFM350XA SERVICE MANUAL: 3GD-28197-12
YFM350XE SUPPLEMENTARY SERVICE MANUAL: 3GD-28197-13
YFM350XJ SUPPLEMENTARY SERVICE MANUAL: 3GD-28197-14
YFM350XKC (for California) SUPPLEMENTARY SERVICE MANUAL: 3GD-28197-15
YFM350XP
SUPPLEMENTARY
SERVICE MANUAL
2001 by Yamaha Motor Corporation, U.S.A.
First Edition, May 2001
All rights reserved.
Any reproduction or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in U.S.A.
LIT-11616-15-09
EB001000
NOTICE
This manual was produced by the Yamaha Motor Company primarily for use by Yamaha dealers
and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one
manual, so it is assumed that anyone who uses this book to perform maintenance and repairs on
Yamaha machine has a basic understanding of the mechanical ideas and the procedures of
machine repair. Repairs attempted by anyone without this knowledge are likely to render the
machine unsafe and unfit for use.
Yamaha Motor Company, Ltd. is continually striving to improve all its models. Modifications and sig-
nificant changes in specifications or procedures will be forwarded to all authorized Yamaha dealers
and will appear in future editions of this manual where applicable.
N
OTE:
Designs and specifications are subject to change without notice.
IMPORTANT INFORMATION
Particularly important information is distinguished in this manual by the following notations.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!
Failure to follow WARNING instructions could result in severe injury or death
to the machine operator, a bystander or a person inspecting or repairing the
machine.
A CAUTION indicates special precautions that must be taken to avoid dam-
age to the machine.
A NOTE provides key information to make procedures easier or clearer.
WARNING
CAUTION:
N
O
TE:
HOW TO USE THIS MANUAL
CONSTRUCTION OF THIS MANUAL
This manual consists of chapters for the main categories of subjects. (See “Illustrated symbols”)
1st title 1: This is a chapter with its symbol on the upper right of each page.
2nd title 2: This title appears on the upper of each page on the left of the chapter sym-
bol. (For the chapter “Periodic inspection and adjustment” the 3rd title
appears.)
3rd title 3: This is a final title.
MANUAL FORMAT
All of the procedures in this manual are organized in a sequential, step-by-step format. The informa-
tion has been compiled to provide the mechanic with an easy to read, handy reference that contains
comprehensive explanations of all disassembly, repair, assembly, and inspections.
A set of particularly important procedure 4is placed between a line of asterisks “*” with each proce-
dure preceded by “●”.
IMPORTANT FEATURES
●Data and a special tool are framed in a box preceded by a relevant symbol 5.
●An encircled numeral 6indicates a part name, and an encircled alphabetical letter data or an
alignment mark 7, the others being indicated by an alphabetical letter in a box 8.
●A condition of a faulty component will precede an arrow symbol 9and the course of action will fol-
low it.
EXPLODED DIAGRAM
Each chapter provides exploded diagrams before each disassembly section for ease in identifying
correct disassembly and assembly procedures.
EB003000
ILLUSTRATED SYMBOLS
Illustrated symbols 1to 9are printed on the
top right of each page and indicate the subject
of each chapter.
1General information
2Specifications
3Periodic checks and adjustments
4Engine
5Carburetion
6Drive train
7Chassis
8Electrical
9Troubleshooting
Illustrated symbols 0to Fare used to identify
the specifications appearing in the text.
0Filling fluid
ALubricant
BSpecial tool
CTorque
DWear limit, clearance
EEngine speed
FΩ, V, A
Illustrated symbols Gto Min the exploded
diagrams indicate the types of lubricants and
lubrication points.
GApply engine oil
HApply gear oil
IApply molybdenum disulfide oil
JApply wheel bearing grease
KApply lightweight lithium soap base grease
LApply molybdenum disulfide grease
MApply silicon grease
Illustrated symbols Nto Oin the exploded
diagrams indicate where to apply a locking
agent Nand when to install a new part O.
NApply the locking agent (LOCTITE)
OReplace
12
34
56
78
90
AB
CD
EF
GHI
J
NO
GEN
INFO SPEC
CHK
ADJ ENG
CARB
DRIV
CHAS
–+
ELEC
TRBL
SHTG
T
R
.
.
EGM
BLS MS
KLM
LT New
CONTENTS
SPECIFICATIONS ........................................................................................... 1
GENERAL SPECIFICATIONS ................................................................. 1
MAINTENANCE SPECIFICATIONS ........................................................ 2
ENGINE ................................................................................................ 2
CHASSIS .............................................................................................. 4
ELECTRICAL ....................................................................................... 4
CABLE ROUTING .................................................................................... 5
PERIODIC CHECKS AND ADJUSTMENTS ................................................... 9
INTRODUCTION ...................................................................................... 9
PERIODIC MAINTENANCE/LUBRICATION INTERVALS ....................... 9
CHASSIS ................................................................................................ 11
ADJUSTING THE FRONT BRAKE .................................................... 11
ADJUSTING THE REAR BRAKE LIGHT SWITCH ............................ 11
CHASSIS ....................................................................................................... 12
FRONT SUSPENSION ........................................................................... 12
ELECTRICAL ................................................................................................. 13
CHECKING THE SWITCH ..................................................................... 13
CHECKING THE SWITCH ................................................................. 13
CHECKING A SWITCH SHOWN IN THE MANUAL .......................... 13
IGNITION SYSTEM ................................................................................ 14
CIRCUIT DIAGRAM ........................................................................... 14
TROUBLESHOOTING ....................................................................... 15
SIGNAL SYSTEM ................................................................................... 20
CIRCUIT DIAGRAM ........................................................................... 20
CHECKING THE SIGNAL SYSTEM .................................................. 21
YFM350XP WIRING DIAGRAM
– 1 –
SPEC
GENERAL SPECIFICATIONS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Model YFM350XP
Model code number: 5NF4 (except for California)
5NF5 (for California)
Spark plug:
Type/manufacturer DR8EA (NGK)
Gap 0.6 ~ 0.7 mm (0.024 ~ 0.028 in)
Electrical:
Ignition system DC. C.D.I.
Charging system A.C. magneto
Battery capacity 12 V 12AH
Battery type GM12CZ-4A-2
Bulb wattage ×quantity:
Headlight 12 V 30 W/30 W ×2
Tail/brake light 12 V 5 W/21 W ×1
Neutral indicator light 12 V 3.4 W ×1
Reverse indicator light 12 V 3.4 W ×1
– 2 –
SPEC
MAINTENANCE SPECIFICATIONS
MAINTENANCE SPECIFICATIONS
ENGINE
Model YFM350XP
Cylinder:
Bore size 82.97 ~ 83.02 mm (3.267 ~ 3.269 in)
Taper limit <0.05 mm (0.002 in)>
Piston:
Piston size “D” 82.92 ~ 82.97 mm (3.265 ~ 3.267 in)
Measuring point “H” 5.5 mm (0.22 in)
(From bottom line of piston skirts)
Piston clearance 0.040 ~ 0.060 mm
(0.00157 ~ 0.00236 in)
Oversize 2nd 83.5 mm (3.287 in)
4th 84.0 mm (3.307 in)
Piston off-set 0.5 mm (0.02 in)
Piston off-set direction Intake side
Inside diameter (piston pin bore) 19.004 ~ 19.015 mm (0.7481 ~ 0.7486 in)
Outside diameter (piston pin) 18.991 ~ 19.000 mm (0.7477 ~ 0.7480 in)
Piston ring:
Sectional sketch
Top ring: Barrel
B 1.2 mm (0.047 in)
T 3.3 mm (0.130 in)
2nd ring: Tapper
B 1.5 mm (0.059 in)
T 3.4 mm (0.134 in)
Oil ring: B 2.8 mm (0.110 in)
T 2.8 mm (0.110 in)
End gap (installed)
Top ring 0.20 ~ 0.40 mm (0.00787 ~ 0.0157 in)
2nd ring 0.20 ~ 0.40 mm (0.00787 ~ 0.0157 in)
Oil ring 0.30 ~ 0.90 mm (0.012 ~ 0.035 in)
Side clearance Top ring 0.03 ~ 0.09 mm (0.0012 ~ 0.0035 in)
2nd ring 0.03 ~ 0.07 mm (0.0012 ~ 0.0028 in)
Clutch:
Friction plate thickness/quantity 2.74 ~ 2.86 mm (0.107 ~ 0.113 in)/6
Warp limit <2.64 mm (0.104 in)>
Friction plate thickness/quantity 2.94 ~ 3.06 mm (0.116 ~ 0.120 in)/1
Warp limit <2.84 mm (0.112 in)>
Clutch plate thickness/quantity 1.5 ~ 1.7 mm (0.059 ~ 0.066 in)/4
1.9 ~ 2.1 mm (0.0748 ~ 0.0827 in)/2
Max. warpage <0.2 mm (0.00787 in)>
Clutch spring free length/quantity 47.8 mm (1.882 in)/5
Clutch spring minimum free length 46.5 mm (1.831 in)
Clutch release method Outer push (rack and pinon)
H
D
B
T
B
T
B
T
– 3 –
SPEC
MAINTENANCE SPECIFICATIONS
Carburetor:
I. D. mark 3GD 00 (except for California)
3GD 10 (for California)
Main jet (M.J) #145
Main air jet (M.A.J) 0.6
Jet needle (J.N) 5J18-3 (except for California)
5J31-1 (except for California)
Needle jet (N.J) O-6 (except for California)
O-6M (for California)
Pilot jet (P.J) #42.5
Pilot air jet (P.A.J.1) 1.0
(P.A.J.2) 0.7
Pilot outlet (P.O) 0.75
Bypass 1 (B.P.1) 0.8
Bypass 2 (B.P.2) 0.8
Bypass 3 (B.P.3) 0.8
Valve seat (V.S) 2.5
Starter jet (G.S.) #62.5
Throttle valve size (Th.V) #125
Fuel level (F.L) 2 ~ 3 mm (0.08 ~ 0.12 in)
Float height 11.4 ~ 13.4 mm (0.45 ~ 0.53 in)
Engine idling speed 1,450 ~ 1,550 r/min
Intake vacuum 33.3 kPa (250 mmHg, 9.83 inHg)
Model YFM350XP
– 4 –
SPEC
MAINTENANCE SPECIFICATIONS
CHASSIS
ELECTRICAL
Model YFM350XP
Brake lever and brake pedal:
Brake lever free play 0 mm (0 in) at lever end
Brake pedal position 10 mm (0.4 in)
Brake pedal free play 8 mm (0.315 in)
Model YFM350XP
C.D.I.:
Magneto model/manufacturer F4T466/MITSUBISHI
Pickup coil resistance 459 ~ 561 Ωat 20 °C (68 °F)
(Color) (White/Red-White/Green)
Rotor rotation direction detection coil resis-
tance
0.083 ~ 0.101 Ωat 20 °C (68 °F)
(Color) (Red-White/Blue)
C.D.I. unit-model/manufacturer F8T38675/MITSUBISHI
Ignition coil:
Model/manufacturer 2JN/YAMAHA
Minimum spark gap 6 mm (0.24 in)
Primary winding resistance 0.18 ~ 0.28 Ωat 20 °C (68 °F)
Secondary winding resistance 6.32 ~ 9.48 kΩat 20 °C (68 °F)
Charging system:
Model/manufacturer F4T466/MITSUBISHI
Nominal output 14 V 15 A at 5,000 r/min
Charging coil resistance/color 0.51 ~ 0.63 Ωat 20 °C (68 °F)/White-White
0.47 ~ 0.57 Ωat 20 °C (68 °F)/White-White
Rectifier/regulator:
Regulator type Semi conductor-short circuit
Model/manufacturer SH640-11/SHINDENGEN
No load regulated voltage 14.1 ~ 14.9 V
Rectifier capacity 14 A
Withstand voltage 200 V
Starter relay:
Model/manufacturer MS5D-611/JIDECO
Amperage rating 100 A
Coil winding resistance 3.9 ~ 4.7 Ω
Otros manuales para WARRIOR YFM350XP
1
Tabla de contenidos
Otros manuales de Motocicleta de Yamaha
Yamaha
Yamaha R15 2022 Manual de usuario
Yamaha
Yamaha PW80(A) Manual de usuario
Yamaha
Yamaha SCORPIO 54D Manual de usuario
Yamaha
Yamaha TT-R90(R) Guía de aplicación
Yamaha
Yamaha R25 Series Manual de usuario
Yamaha
Yamaha MT-10 2021 Manual de usuario
Yamaha
Yamaha XSR900 2019 Manual de usuario
Yamaha
Yamaha DT125RE 2005 Manual de usuario
Yamaha
Yamaha FJR13ESE(C) Manual de usuario
Yamaha
Yamaha YZF-R6R Manual de usuario
Yamaha
Yamaha YZF-R1S Manual de usuario
Yamaha
Yamaha R15 Manual de usuario
Yamaha
Yamaha VIRAGO XV250S Manual de usuario
Yamaha
Yamaha TDM850 Manual de usuario
Yamaha
Yamaha DT230 4TP3-AE1 Manual de usuario
Yamaha
Yamaha XT660R Manual de usuario
Yamaha
Yamaha XVS13AW 2006 Manual de usuario
Yamaha
Yamaha Virago XV535L Manual de usuario
Yamaha
Yamaha Bolt XVS95CH Manual de usuario
Yamaha
Yamaha YZ85G Manual de usuario
Manuales populares de Motocicleta de otras marcas
APRILIA
APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manual de usuario
KTM
KTM Freeride E-XC 2021 Manual de usuario
Fantic
Fantic Enduro 125 Manual de usuario
Ducati
Ducati Supersport 750 desmodue Manual de usuario
MV Agusta
MV Agusta 2008 F4 312RR 1078 Manual de instrucciones
Ducati
Ducati 748 monoposto strada Manual de usuario
ATK
ATK 1988 250 Manual de usuario
Excelsior-HENDERSON
Excelsior-HENDERSON 1999 HCX Manual de usuario
Triumph
Triumph Thunderbird Manual de usuario
Ducati
Ducati 996 Manual de usuario
BMW
BMW MOTORRAD K 1200 R Sport Manual de instalación y mantenimiento
BMW Motorrad
BMW Motorrad G 650 GS 2007 Manual de instalación y mantenimiento