Yaesu FTH-2006 Manual del propietario

Otros manuales para FTH-2006

1

Tabla de contenidos

Otros manuales de Transceptor de Yaesu

Yaesu

Yaesu FT-301D Manual de usuario

Yaesu

Yaesu FT-857D Manual de usuario

Yaesu

Yaesu VX-8GR Manual de usuario

Yaesu

Yaesu VX-6R Manual de usuario

Yaesu

Yaesu FT-470 Manual de usuario

Yaesu

Yaesu FT-901DM Manual

Yaesu

Yaesu FT-7100M Manual de usuario

Yaesu

Yaesu FT-897 Manual

Yaesu

Yaesu FT-8000R Manual de usuario

Yaesu

Yaesu VX-60R Manual de usuario

Yaesu

Yaesu FTM-100DR Manual de usuario

Yaesu

Yaesu FT1DR Manual de usuario

Yaesu

Yaesu FTM-350R - SOFTWARE UPDATE PROCEDURE 7110 Manual de usuario

Yaesu

Yaesu FTDX10 Manual

Yaesu

Yaesu FTDX101D Manual de usuario

Yaesu

Yaesu PEP2000 - UPDATE V0150 AND V11.53 Manual técnico

Yaesu

Yaesu FT-450D Manual de usuario

Yaesu

Yaesu FT3DR Manual de usuario

Yaesu

Yaesu FTV-700 Manual de usuario

Yaesu

Yaesu FT-950 Manual técnico

Yaesu

Yaesu FT-757GX II Manual de usuario

Yaesu

Yaesu FT-One Manual de usuario

Yaesu

Yaesu FT-757GX II Manual del propietario

Yaesu

Yaesu VX-5R Manual de usuario

Manuales populares de Transceptor de otras marcas

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario

Uniden

Uniden UH820 Series Manual de usuario

PROGRAMMING YAESU FTH-2006

Programming this rig needs only a small screwdriver and some skill, no computer or

interface cords are needed.

Normally this rig display only a channel number "CH 0" to "CH 9" if all memories

where programmed.

You can't modify the frequency with the 4 keyboard's keys. But there are some (4)

hidden keys somewhere to achieve this.

A) Right of the display, remove the keyboard plastic cover with a small screwdriver or

a knife (it's glued) and you will see 4 additional keys on the keyboard just under the

originals.

B) Those keys are like this:

1) Power on the rig

2) Change display from channel to frequency by pressing once the "hidden"

"Channel/Frequency" key.

3) Adjust to the desired frequency using the big upper right knob or "Scan +" or

"Scan –" keys (You can obtain a 1 MHz step depressing the "Function" key

before turning the knob or "Scan +" or "Scan –" keys.

4) From the frequency display, press the "Function" key (a small F is displayed)

and quickly press the "Channel/Frequency" key, a small blinking memory

number will appear in the upper left corner of the display, change the memory

number using the big upper right knob or "Scan +" or "Scan –" keys and press

again the "Channel/Frequency" key to store the memory.

5) Back to "channel display" mode using the "Channel/Frequency" key, the

desired frequency is stored in the chosen memory.

To use a "shift" (repeater operation), press the "Channel/Frequency" key and power

on the rig, the display shows .000, rotate the big upper right knob to change to the

desired value, then the "Function" key (small F in display) and the "Priority" key to

display a +or -

CTCSS

Under the "Light" key there is the key for the CTCSS

First press will enable CTCSS at transmit ("enc" displayed).

Second press of the key will enable CTCSS at receive ("dec" displayed)

Third press of the key will disable both.

Pressing the "Function" key and then the "CTCSS" key you can adjust the CTCSS

frequency.

In fact, programming this rig is exactly like the well-known FT-23R except for some

functions

Some other adjustments are inside the box (solder pads) (Do it at your own risks!)

Default setup is:

Solder pads

1 open

2 shorted

3 open

4 shorted

5 shorted

6 open

7 open

8 open

9 open

10 shorted

Frequency step is solder pad #4: open = 5 KHz step, shorted = 12.5 KHz step.

(May needs replacing some components)

Battery saver is solder pad #6: open = on, shorted = off

Channel / frequency display is solder pad #7: open = channel, shorted = frequency

Busy channel lock out is solder pad #8: open = off, shorted = on

Busy tone lock out is solder pad #9: open = off, shorted = on

Behind PTT rubber cover you will find a switch for testing/clone mode

That's all

Enjoy

F6BXM