Yaesu FT-450D Manual de usuario

8/23/16

This procedure is used to update the flash programming for

the FT-450Dtransceiver.

CAUTION

Verify your radio is the FT-450D by the logo on the right side of the transceiver front panel.

Do not install this firmware to your FT-450 or FT-450AT. The firmware is not compatible

and will not operate at all.

The update firmware is available from our website at http://www.yaesu.com.

Ver. 0244 implements improvements:

•Improved and optimized.

The firmware updates will work with all versions (AF, AS, EU, NA, OC, SA or all Countries)

of the FT-450D.

PART 1

Install the data file to PC

1. Down load the FT-450D data file [FT-450D_V0244_w_FSW006_20160823.zip] from the

following website:

http://www.yaesu.com/indexVS.cfm?cmd=DisplayProducts&ProdCatID=102&encProdID=8

70B3CA7CFCB61E6A599B0EFEA2217E4&DivisionID=65&isArchived=0

2. Save the FT-450D data file [FT-450D_V0244_w_FSW006_20160823.zip]to a temporary

folder on your hard drive.

3. Unzip and Extract the contents of “FT-450D_V0244_w_FSW006_20160823.zip” to a

desktop or local disk C:\temp of your computer.

4. Two files named [FSW006_V203.exe] and [Ah024_v0244.sfl] will be found in a desktop or

local disk C:\temp. PART 2

RS-232C, DB9F to DB9F straight cable

*You will need a serial cable RS-232C, DB9F to DB9F straight cable to connect the FT-450D

transceiver to your computer.

*Don't forget to write down any menu settings you have changed from the default

before you start.

1. Turn the FT-450D off and disconnect the DC power cable.

2. Locate the program switch thru the access hole on the bottom at the front left corner of the

radio. Carefully move the switch to the right (program position).

3. Connect the serial straight through programming cable, DB9F to DB9F, connector to the

serial port COM1 in the back of your computer. Plug the DB9F connector to the CAT

connector on the FT-450D.

NOTE:

You may also use a USB to Serial adaptor such as the RT-Systems (RTS-03) being one

example, if the DB-9 (RS-232C) serial port is not available on your computer. (There are

many adapters available; however some may not function with this firmware. We recommend

using the latest USB adapter driver firmware when available). If the installation is not

successful, the radio may not power on. In this case you should not use the USB adapter. Use

another computer with a serial port DB-9 (RS-232C) and do the firmware update with a DB-9

straight cable as described in steps #1 to #3.

4. Leave the FT-450D turned OFF and connect the DC power cable.

5. Now go to the desktop or local disk C:\temp and find the FSW006 as shown below.

Double-click the FSW006 icon, displayed on the Program Screen.

6. Confirm the SFL file is AH024_V0244.SFL. If it is necessary to change the COM Port, Click

"Configure"

7. Click WRITE. The onscreen progress bar will indicate programming activity.

8. When programming has completed, “Confirm” will be displayed.

9. Disconnect the DC power cable and then remove the DB9 serial programming cable.

10. Thru the access hole on the bottom of the radio, move the program switch to the left, operate

position.

11. Reconnect the DC power.

12. Press and hold the Home/Recall button, and press the Power button to turn the FT-450D on

to reset the defaults. The FT-450D will show 7.000.00 MHz.

The updating process is now complete.

The firmware version can be displayed on the radio

While holding the MODE button turn the radio on. The firmware version will be displayed in

the window 0244. Then turn the radio off and back on again for normal operation.

We hope this new firmware will increase your enjoyment of your FT-450D. Thank you for choosing

Yaesu radios. If you have any problems or questions, please contact Yaesu, Amateur Tech Support

amateurtech@yaesu.com.

Best regards,

Mikio Maruya, WA6F

Executive Vice President

Engineering & Customer Service

Yaesu USA

Yaesu USA | 6125 Phyllis Drive | Cypress, CA 90630 | 714.827-7600 | FAX: 714.827-8100

http://www.yaesu.com

Otros manuales para FT-450D

Tabla de contenidos

Otros manuales de Transceptor de Yaesu

Yaesu

Yaesu FV-107 Manual de usuario

Yaesu

Yaesu FTDX101MP Guía de referencia

Yaesu

Yaesu FT-102 Manual de usuario

Yaesu

Yaesu 600 Manual de usuario

Yaesu

Yaesu VX-6R Manual de usuario

Yaesu

Yaesu FT-707 Manual de usuario

Yaesu

Yaesu FT-101 Manual de usuario

Yaesu

Yaesu FT-2500M Manual

Yaesu

Yaesu FTM-10R Manual de usuario

Yaesu

Yaesu FTM-6000R Manual de usuario

Yaesu

Yaesu FTM-3200DE Manual de usuario

Yaesu

Yaesu FTM-400DR Manual de usuario

Yaesu

Yaesu FT-100D Manual de usuario

Yaesu

Yaesu FT DX 3000 Manual de usuario

Yaesu

Yaesu FT-301 Manual de usuario

Yaesu

Yaesu FT-90R Manual de usuario

Yaesu

Yaesu FTA-750L Manual de usuario

Yaesu

Yaesu FT-900 Manual de usuario

Yaesu

Yaesu Mark-V FT-1000MP Manual de usuario

Yaesu

Yaesu FT-8900R Manual de usuario

Yaesu

Yaesu FT-3000M Manual de usuario

Yaesu

Yaesu FT-450D Manual de usuario

Yaesu

Yaesu FT-2200 Manual

Yaesu

Yaesu FT-2600M Manual de usuario

Manuales populares de Transceptor de otras marcas

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario

Uniden

Uniden UH820 Series Manual de usuario