Xylem LOWARA Manual

Presfix Fill Set

Operating and Maintenance Instructions

EC Declaration of conformity

Xylem Water Solutions UK Limited declare that the Presfix pressurisation set conforms to the requirements of

the Machinery Safety Directive 2006/42/EC.

Conforming to the UK Health & Safety Requirements 2008 No.1597

Water supply (Water fittings) regulations 1999

Code of practice for heating and chilled water systems BS7074 (parts 1, 2 & 3)

Signed: Position: Engineering manager Date: 20-04-2016 Revision B

Clive Willmott

Introduction

This leaflet contains information to enable the safe installation and operation of the products mentioned above.

The following instructions must be read and understood by all persons responsible for the installation, operation

and maintenance of this product.

Warning Symbols

Safety instructions where noncompliance would affect safety.

Safety instruction where electrical hazard is involved.

Safety instruction where noncompliance could cause damage to the equipment.

Instruction for safe use

This product has been designed for the pressurisation of sealed heating, chilled water and closed-

condenser water systems to the operating conditions shown.

This product should not be installed until this leaflet has been studied carefully.

Handling, transportation and installation of this equipment should only take place with the proper

use of lifting equipment.

This product must be stored in a frost-free dry environment.

Noise Emissions

This equipment operates at a noise level lower than 70dBA.

Protection degree IP2X

Installation

The Presfix Fill unit is despatched mounted on a wooden pallet and covered in a protective film, it is recom-

mended that the unit be retained in the protective packaging until the product is to be installed.

The unit will arrive pre-packaged and wired ready for installation.

This product has been fully run tested at our works under simulated site conditions.

The unit should be sited in a dry clean well-ventilated area with good all round access.

Electrical connections

The input supply to the switched spur is fed from the main pressurisation unit output terminals 1,2&3. This

output is only active when the main pressurisation unit is calling for water top up.

The low water cut out float switch is wired back to the main pressurisation unit terminals 43&45

Drawing M10127-1 attached gives connection details. The cable must be of adequate size to

carry the motor full load current. This is shown on the duty plate. All non power caballing should

be limited to 2.5mm².

All connections must be made using the appropriate wiring drawings for the equipment being

installed, with particular attention being paid to the supply voltages.

The supply voltage is shown on the set duty plate.

Never operate this product with the control panel or switched spur lid removed.

It is essential that this equipment is earthed to the building earth system.

The base frame must be earth bonded directly to the building earth system.

All wiring should be arranged such that it enters the control boxes through the appropriate

cable glands.

Water supply and system connection

Connect the Presfix Fill set ½”BSP ball valve (left side of break tank) to a suitable water supply, incorporating

an approved stop cock.

If the pressure available at the ball valve is below 0.3 bar, a low pressure orifice must be

obtained and fitted.

Extend the ¾” plastic overflow pipe from the Presfix break tank to a position where an overflow

will be noticed and rectified. Ensure the warning pipe is able to handle the incoming water

volume, if this is not the case then a reducing valve should be fitted to the incoming water supply.

Connect the pressurisation port ½” BSP (right hand side of unit) to the main system expansion vessel Fill

point , details of connection point will be found in the main pressurisation unit O&Ms

Note: This product has a type AB air gap and contains a weir which is intended to spill over if a catastrophic

failure occurred, If it is not acceptable to spill water directly to the floor then this product should be mounted

on a try which should then have a discharge connection to drain.

Commissioning

1. Commissioning should be carried out in conjunction with the main pressurisation set commissioning de-

tails. Fill the main system with water via the quick fill filling loop to the system fill pressure, this

filling loop must comply with local water authority bylaws and contain double check valves. The

filling loop must be completely removed after the system has been filled.

The pressurisation unit/Fill set must never be used to fill the system.

The maximum running time for pumps fitted to the Fill set must not exceed 4 hours in any 24

hour period.

2. Turn on the water supply feeding the Fill set break tank.

Water treatment crystals/chemicals must never be introduced to the system via the break tank.

3. Check that the pump has been fully evacuated of all air by removing the bleed screw from pump and

allow water to escape until no air is present. Replace bleed screw.

Operation

Switch the main power supply to the pressurisation system to the on position. Turn the switched spur situated

at the front of the Fill unit to the on position.

When the main pressurisation unit senses that the system is low on water it will give a 230v supply to the Fill

set and start the Fill set pump, this will pump water into the pressurisation set vessel which will be sitting at at-

mospheric pressure, when the main vessel senses that it now has the correct water content it will switch off

the supply to the Fill set pump. The Fill set will remain inactive until another signal is given from the main

pressure set to call for more water.

Flow regulating valve

The Fill set has a flow regulating valve which should be set to approximately 5l/m this is to ensure that the

break tank inlet water supply can keep up with demand. This can be adjusted to give a larger volume pro-

vided the main water supply can keep up.

Low level float switch

The low level float switch in the Fill unit will monitor the break tank water level and signal the main pressurisa-

tion to switch off the power to the Fill unit preventing the pump from running dry.

Maintenance

Routine check (3 monthly intervals)

1. Check that the pump seal is not leaking.

2. Check the pump is not seized and develops the correct pressure.

3. Check that the pump operates without undue noise or vibration.

4. Check that the motor runs without overheating.

Routine check (6 monthly intervals)

1. Check the break tank is clean and that the correct water level has been maintained.

2. Check that all screws are tight on electrical components.

3. Check that the earth connections are tight and making good contact.

Xylem Water Solutions UK Limited

Millwey Rise Industrial Estate

Axminster, Devon EX13 5HU - UK

Tel: 01297 630230

Fax: 01297 630270

[email protected]

www.lowara.co.uk

www.xyleminc.com

Lowara is a trademark of Xylem Inc. or one of its subsidiaries.

Lowara reserve the right to make modifications without prior notice.

Code UKLIT0124 P04/16

Tabla de contenidos

Otros manuales de Bomba de agua de Xylem

Xylem

Xylem LOWARA e-LNEEE Series Manual

Xylem

Xylem Bell & Gossett 1335 Series Manual de usuario

Xylem

Xylem GOULDS e-SVE Series Manual de usuario

Xylem

Xylem Goulds SHV Series Manual

Xylem

Xylem Bell & Gossett e-3530 Series Manual de usuario

Xylem

Xylem GOULDS RGS2012 Manual de usuario

Xylem

Xylem Bell & Gossett PL Series Manual de usuario

Xylem

Xylem GSP0311 Manual de usuario

Xylem

Xylem Bell & Gossett GLC Series Manual de usuario

Xylem

Xylem GOULDS e-SVI Series Manual de usuario

Xylem

Xylem Lowara Z8 Series Manual de usuario

Xylem

Xylem Jabsco 18620-0003 Manual de usuario

Xylem

Xylem G&L A-C 9100 Series Manual de usuario

Xylem

Xylem Jabsco Ballast King 22610-9007 Manual de usuario

Xylem

Xylem AC Fire Pump 8100 Series Manual de usuario

Xylem

Xylem Flygt 2250 Manual de usuario

Xylem

Xylem Laing Thermotech ecocirc E Series Manual de usuario

Xylem

Xylem Flygt 2008 Ready 8 Instrucciones de instalación y funcionamiento

Xylem

Xylem LOWARA e-SHE Series Manual de usuario

Xylem

Xylem Rule LoPro LP900S Manual de usuario

Xylem

Xylem GOULDS 45HB-70HB Instrucciones de funcionamiento

Xylem

Xylem JABSCO 42755 Series Manual de usuario

Xylem

Xylem DRAINAGE RED JACKET Series Manual

Xylem

Xylem FLYGT APP 412 Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario

STA-RITE

STA-RITE ST33APP Manual de usuario