XPR Access BIOC3 V1 Manual de usuario
www.xprgroup.com 1
BIOC3 V1
Biometric Reader
EN
USER’S MANUAL
v. b1
www.xprgroup.com 2
Contents
1. DESCRIPTION
2. SPECIFICATIONS
3. MOUNTING
4. WIRING
5. CONNECTING BIOMETRIC READERS TO EWS CONTROLLER
5.1 CONNECTING BIOMETRIC READERS IN SAME RS485 LINE WITH THE EWS CONTROLLERS
5.2 CONNECTING BIOMETRIC READERS WHEN ALL THE CONTROLLERS HAVE TCP/IP COMMUNICATION
6. CONNECTING BIOMETRIC READERS TO 3RD PARTY CONTROLLER
6.1 CONVERTERS PIN DESCRIPTION
7. ENROLLMENT
8. CONFIGURING THE BIOMETRIC READERS IN PROS SOFTWARE
8.1 ADDING BIOMETRIC READER
8.2 ENROLLING FINGERPRINTS FROM A READER
8.3 ENROLLING FINGERPRINTS FROM DESKTOP READER
8.4 DELETING FINGERPRINTS
8.5 UPLOADING THE FINGERPRINTS TO THE BIOMETRIC READERS
8.6 FIRMWARE UPDATE
8.7 SENSOR CALIBRATION
8.8 SEND CONFIGURATION
8.9 ADVANCED SETTING
9. CONFIGURING THE BIOMETRIC READERS IN BIOMANAGER
9.1 ADD PORTAL
9.2 ADD READER
9.3 EDIT READER
9.4 DELETE READER
9.5 ADD USER
9.6 DELETE FINGERPRINTS
9.7 UPLOADING THE FINGERPRINTS TO THE BIOMETRIC READERS9.12 CUSTOM WIEGAND
9.8 CUSTOM WIEGAND
10. WIEGAND PROTOCOL DESCRIPTION
11. SAFETY PRECAUTIONS
3
3
3
4
4
5
5
6
6
7
7
7
8
9
10
10
11
11
11
11
12
12
12
13
13
14
14
15
16
17
18
www.xprgroup.com 3
1. DESCRIPTION
2. SPECIFICATIONS
3. MOUNTING
Fingerprint capacity up to 9500 ingerprints
Technology Biometry
Authentication Finger
Fingerprints per user 110 ingerprints
Interface Wiegand 8 to 128 bits; Default: Wiegand 26bit
Protocol programming By PROS software (EWS system) and BIOMANAGER (all access control systems)
Cable distance 50m
Fingerprint Sensor Type Capacitive
1:1000 identiication time 970 msec, including feature extraction time
Fingerprint enrolment On the reader or from the USB desktop reader
Panel Connection Cable, 1m
Green and Red LED Externally Controlled
Orange LED Idle mode
Buzzer Yes
Backlight ON/OFF Yes, by software settings
Tamper Yes
Consumption 100mA
IP Rating 54
Power supply 914V DC
Operating Temperature 0°C to +40°C, non-condensing
Dimensions (mm) 92 x 51 x 25
Housing
Moulded Aluminium
Colour
Silver, Red, Green, Dark Grey, Blue, White
BIOC3 is a Wiegand biometric reader for indoors access control applications. It oers storage up to 9500 ingerprints and
programmable Wiegand Output (8 to 128 bits).
Coniguration of the readers and ingerprint enrollment is done through PC Software.
Connection between the biometric readers is RS485 and it is used for ingerprint transfer and coniguration.
When used with third party controllers, the connection between the Biometric readers and the PC is done through a converter
(CNV100RS485 to RS232 or CNV200RS485 to USB or CNV300RS485 to TCP/IP). Only one converter is needed per system (one
converter for 1, 2, 3...30, 31 Biometric readers)
The tamper switch output can trigger the alarm system, if an attempt is made to open or remove the unit from the wall.
www.xprgroup.com 4
4. WIRING
5. CONNECTING BIOMETRIC READERS TO EWS CONTROLLER
- The Biometric readers can be connected to virtually any controller that conforms to Wiegand format standards (standard Wiegand
26bit or self-deined Wiegand).
- The lines D0 and D1 are the Wiegand lines and the Wiegand Number is sent through them.
- The RS485 line (A, B) is used for ingerprint transfer and reader settings.
- The Biometric readers must be powered from the controller.
- If you use dierent power supply for the biometric reader, connect the GND from the both devices to ensure correct transfer of
the wiegand signal
- When you have connected the reader and powered on, the LED should lash in orange light + 2 beeps. This lets you know it’s on
and ready for use.
- Fingerprint enrollment is done from the PC Software. Connection between the Biometric readers and the PC must be established.
www.xprgroup.com 5
5.1 CONNECTING BIOMETRIC READERS IN SAME RS485 LINE WITH THE EWS CONTROLLERS
• The Biometric readers are connected through RS485 bus. The same RS485 bus that the EWS controllers are connected to.
• Maximum units in one network (EWS + Biometric readers) is 32.
• If there are more than 32 units in one network, please utilize RS 485 HUB to connect.
• The RS485 Line should be conigured in the form of a daisy chain, NOT in a form of a star. If star must be used in some points, keep
the stubs from the RS485 backbone as short as possible. Maximum length of the stub is dependant of the installation (total
number of devices in RS485 line (total cable length, termination, cable type...) so recommendation is to keep stubs shorter than
5 meters, keeping in mind that this can be possible reason for errors in communication with PC software
• The cable must be twisted and shielded with a min. 0.2 mm2 cross section.
• Connect the ground (0V) of each unit in the RS 485 Line using a third wire in the same cable.
• The shield of the communication cable between two devices must be connected to the EARTH from ONE side of the RS 485 Line.
Use the side that has earth connection to the building’s grounding network.
5.2 CONNECTING BIOMETRIC READERS WHEN ALL THE CONTROLLERS HAVE TCP/IP COMMUNICATION
• When all the controllers are connected via TCP/IP, then the RS485 network becomes local (from Reader 1 to the Controller then
to the Reader 2).
• Connect the readers directly to the Rs485 terminals in each controller.
• If the distance Reader-Controller is high (50meters) and if the communication with the reader can not be established, then
terminate the RS485 network by closing the jumper in the EWS Controller or as described in chapter 4.
www.xprgroup.com 6
6. CONNECTING BIOMETRIC READERS TO THIRD PARTY CONTROLLERS
6.1 CONVERTERS PIN DESCRIPTION
• Connect the lines D0, D1, Gnd and +12V to the third party controller.
• Connect the RS485 Line (A, B) to the converter. Connect the converter in the PC.
• Fingerprint enrollment is done from the PC Software. Connection between the Biometric readers and the PC must be estab
lished.
• The Biometric readers communicate with each other with a RS485 and with the PC Software through a Converter.
• The RS485 Line should be conigured in the form of a daisy chain, NOT in a form of a star. Keep the stubs from the RS485 back
bone as short as possible (not more than 5 meters)
• Only one converter per installation is needed, not per reader.
CNV200
Converter Rs485 to USB
Requires installation as USB serial de-
vice (refer to CNV200 Manual). The
Drivers are located on the CD.
CNV1000
Converter Rs485 to TCP/IP
Does not require installation. IP address
set through Internet Browser(refer to
CNV1000 Manual)
BIOPROXUSB
USB DESKTOP READER
OPTIONAL
www.xprgroup.com 7
7. ENROLLMENT
8. CONFIGURING THE BIOMETRIC READERS IN PROS CS SOFTWARE
8.1 ADDING BIOMETRIC READER
1. Expand the Door item to view the readers
2. Right click on the reader and select properties (8.1)
3. In the Basic tab, for “Type” of the Reader select “BIOC3”. (8.2)
4. After selecting the type, a third tab will appear “Biometric”. Go to that tab and put the serial number of the Biometric Reader. (8.3)
Important Note: The serial number of the reader can be found on a sticker inside the reader, on the packaging box and it can be
search from the software (right click on the portal/search devices/readers). (8.4 & 8.5)
To check if the reader is On Line, right click on the reader and select “Check version”. In the Event Window a message should appear
“Device ON Line, Type: BIOC3” (8.6)
www.xprgroup.com 8
8.2 ENROLLING FINGERPRINTS FROM A READER
1. Open the Users Window and create a new user.
Click on “New User”, put a name and ID(card number). (8.7)
2. Go to the “Biometric” Tab
3. Select the reader(with left click) from which the enrollment will be done. (8.8)
4. Right click on the ingertip and select enroll. (8.9)
5. In the next 25 sec. present the inger on the selected reader and the inger tip will turn red, with the percentage of
successful enrollment shown next to the ingertip. (8.10)
In these 25 sec. the reader will continuously blink in orange.
6. Repeat point 4&5 for each inger that should be enrolled.
7. Click on “Save New” and the ingerprint will be sent automatically to all Biometric Readers where that user has access, i.e. to
all the readers according to the Access Level assign to that user.
Example:
If the user has “Unlimited” Access level then the ingerprints will be sent to all readers, if the user has Access level only for
Reader1 and Reader 3 then the ingerprints will be sent only to those two readers.
Note:
To check if all the ingerprints are sent to the reader, right click on the reader and select “Memory Status”. (8.11)
In the event window a line will appear indicating the number of ingerprints stored in the reader. (8.12)
Note:
If more ingerprints are added for one user, all ingerprints will send the same Wiegand Code to the controller, the one written
in the ield User ID(card Number).
www.xprgroup.com 9
8.3 ENROLLING FINGERPRINTS FROM DESKTOP READER
Plug the Desktop Reader in the PC. It is installed in the same way as a USB Device. When the desktop reader has been installed it will
automatically appear in the Software. (8.13)
1. Open the Users Window and create a new user.
Click on “New User”, put a name and ID(card number). (8.7)
2. Go to the “Biometric” Tab
3. Select the USB desktop Reader (with left click).
4. Place the inger on the BIOPROXUSB, right click on the ingertip and select enroll. (8.9)
5. The inger tip will turn red, with the percentage of successful enrollment shown next to the ingertip. (8.10)
6. Repeat point 5 for each inger that should be enrolled.
7. Click on “Save New” and the ingerprint will be sent automatically to all Biometric Readers where that user has access, i.e. to all
the readers according to the Access Level assign to that user.
If the reader is o line, the ingers will be sent upon the connection is established between PROS server and the reader. No need for
additional enrollment or actions. The ingerprints will be sent as soon as communication is established.
Example:
If the user has “Unlimited” Access level then the ingerprints will be sent to all readers, if the user has Access level only for Reader1
and Reader 3 then the ingerprints will be sent only to those two readers.
Note:
To check if all the ingerprints are sent to the reader, right click on the reader and select “Memory Status”. (8.11)
In the event window a line will appear indicating the number of ingerprints stored in the reader. (8.12)
Note:
If more ingerprints are added for one user, all ingerprints will send the same Wiegand Code to the controller, the one written in
the ield User ID(card Number).
www.xprgroup.com 10
8.4 DELETING FINGERPRINTS
8.5 UPLOADING THE FINGERPRINTS TO THE BIOMETRIC READERS
In General, the ingerprints are stored in the Biometric reader and in the Software.
Deleting can be done only in the readers or from both places.
Deleting one user from the biometric reader
Select the User
Click on “Delete User”. The User together with its ingerprints will be deleted from both the software and the
ingerprint readers. (8.14)
Deleting all users from the biometric reader
Right click on the reader and select “Delete all users from reader” (8.15)
Delete one or more ingerprints
Select the User and open the “Biometric” tab
Go to the ingertip that needs to be deleted, right click and select ”Delete” for one inger or “Delete All” for all ingers
of the User.
Click “Save Changes”.
With this procedure the User’s ingerprints are deleted from the software and from the reader. (8.16)
Right click on the biometric reader
Select “Upload all users to reader”
While receiving the ingerprints the reader will blink in orange.
Note: Use this feature when you change or add a reader, if pending tasks are
deleted in the software or if there are doubts that ingerprints in the reader
memory are not synchronized with the software database.
In normal usage, the ingerprints are sent automatically and this feature is
not used.
Tabla de contenidos
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
