XPPen Deco Series Manual de usuario
User Manual
Deco Series Pen Tablet
2
Contents
I. Overview
II. Accessories
III. Connection
IV. Support system
V. Download
VI. Driver installation
VII. Introduction to driver
i. Work area
a. Screen
b. Pen Tablet/Pen Display
ii. Application
iii. Pen settings
iv. Shortcut keys
v. Settings
VIII. Driver uninstall
3
I Overview
1. Lanyard hole
2. Power key: Press and hold it for 3 seconds to turn on or off the pen tablet
3. USB-C port
4. Shortcut keys
5. Indicator 1
a. Flashing: Stylus is in range, but not touching the work area
b. Solid: Stylus is touching the work area and functions properly
c. No light: Stylus is out of detection range
6. Indicator 2
In blue status:
a. Flashing slowly: Bluetooth disconnected
b. Flashing quickly: Waiting for pairing Bluetooth (Long press the shortcut key
on the top left for 3 seconds)
c. Solid: Successfully paired
In red status:
4
a. Flashing: Low battery (20% battery remaining)
b. Solid: Charging
c. No Light: Fully charged
In purple status:
The red and the blue indicator are both on simultaneously
7. Work area
* All descriptions and pictures shown are for reference only and may differ from the actual
products.
II Accessories
* All descriptions and pictures shown are for reference only and may differ from the actual
products.
III Connection
Wired Connection
Connect the pen tablet to your computer. And make sure you can use the stylus to control the
cursor.
5
Wireless Connection (Wireless Connection (on models that support such function)
A. Connect via the Bluetooth receiver
Plug the Bluetooth receiver into the computer.
Press and hold the power key for 3 seconds to turn on the pen tablet.
B. Direct Bluetooth connection (Windows 10 or later/Mac OS X 10.10 or later)
1. Press and hold the power key for 3 seconds to turn on the pen tablet. Then
press the shortcut key on the top left for 3 seconds to enter Bluetooth
pairing (with the blue indicator flashing quickly).
2. Turn on the Bluetooth on the computer. Set up and add Bluetooth device.
Search for device name and complete Bluetooth pairing by clicking the
device name (with the blue indicator always on).
3. Press and hold the power key for 3 seconds to turn off the pen tablet.
6
IV Support system
Windows 7 or later;
Mac OS X 10.10 or later;
Android 6.0 or later;
Chrome OS 88 or later;
Linux.
V Download
Please download the corresponding driver according to your product model from the XP-PEN
official website (https://www. xp-pen.com).
VI Driver installation
You must install the driver for your device to work properly; If you uninstall the driver, reinstall
the latest driver from the XP-PEN official website (https://www. xp-pen.com).
Windows:
Navigate to the driver file you downloaded, unzip it, run the "exe" file with administrator
privileges, and then follow the prompts to complete the installation.
7
Mac:
Navigate to the driver file you downloaded, unzip it, run the "dmg" file, and then follow the
prompts to complete the installation. During installation, you will be prompted to add the
required security settings (For the standard models: System Preferences -> Security & Privacy
-> Accessibility; For the Bluetooth models: System Preferences -> Security & privacy ->
Accessibility, Bluetooth). Please ensure that all XP-PEN options have been selected. Otherwise,
the device and driver will not work properly.
Linux:
DEB: Open the terminal window, enter "sudo dpkg –i" and execute the command after
dragging the installation file into it;
RPM: Open the terminal window, enter "sudo rpm –i" and execute the command after dragging
the installation file into it;
Tar.gz: Please unzip it first, then enter "sudo" in the terminal window, drag "install.sh" into it,
and then execute the command.
Notes:
1. Before installation, please close all opened antivirus software and painting applications.
2. If other drivers have been installed on the computer, please uninstall them first.
3. Restart the computer after installation.
4. For the best performance of your device, we highly recommend you check and update the
driver regularly from XP-PEN official website.
8
VII Introduction to driver
If the device is successfully connected to the computer, the device’s picture will be displayed on
the driver interface. If the connection fails, restart your computer or driver. Multiple devices can
be connected at the same time, and up to three devices are supported. After switching one of
the devices, user-defined settings can be made for the current device, and the settings only work
for the currently selected device.
Save settings:
Please click the "OK" button on the left side of the driver interface to save the settings after
changing the configuration; otherwise, the changed settings will work only for the current use.
i Work area
a. Screen
If multiple monitors are used in duplicate mode, the device’s work area will be mapped to all
monitors. When the stylus moves in the device’s work area, the cursor on all monitors will move
at the same time. If multiple monitors are used in extended mode, on the driver interface, select
which monitor the device’s work area is mapped to.
9
The screen’s display area can be set in the following three ways:
1. Set full screen: Set the display area of the selected monitor to the maximum.
2. Set screen area: Manually set the screen’s display area with the mouse.
3. Customize: Manually enter coordinates in the corresponding input boxes below X, Y, W and
H to customize the size of the screen’s display area, or use the mouse to drag on the screen icon
of the driver interface to adjust the screen’s display area.
Identify:
Identify all connected monitors, and numeric identifiers will be displayed in the lower-left corner
of each monitor.
b. Pen Tablet/Pen Display
Define the relationship between pen movement on the device and cursor movement on the
display.
The device’s work area can be set in the following four ways:
1. Full area: Maximize the device’s work area.
2. Proportion: Scales the device’s work area to the entire display area of the selected monitor.
3. Set area: Use the stylus to click the "upper left corner" position and the "lower right corner"
position on the device to select its work area.
10
4. Customize: Manually enter coordinates in the corresponding input boxes below X, Y, W and
H to customize the size of the device’s work area, or use the stylus to drag on the device icon
on the driver interface to set the size of the device’s work area.
Rotation setting:
You may set the device to 0°, 90°, 180° & 270°. After finishing the setting, you also need to
rotate the device in the corresponding direction.
Rotating 180° means to change to the left-handed mode.
ii Application
Customize all keys’ functions and adjust pressure for different applications on the current device.
When switching between different applications, the driver will be identified automatically. Once
all applications selected, the function works for all applications. Click a single application, and
the function will only works for the currently selected application.
1. Click the "+" on the top right of the application bar to open the application selection
interface.
2. Select application to be added from the running applications or click the "browse" button to
add from the installed applications.
3. Click "OK" and the selected application will be added to the application bar.
Otros manuales para Deco Series
1
Tabla de contenidos
Otros manuales de Tableta de XPPen
XPPen
XPPen Deco Pro Series Manual de usuario
XPPen
XPPen Deco Pro Small Manual de usuario
XPPen
XPPen STAR 05 Manual de usuario
XPPen
XPPen Deco mini7 Manual de usuario
XPPen
XPPen Deco Series Manual de usuario
XPPen
XPPen Star G430 Manual de usuario
XPPen
XPPen Deco mini7W Manual de usuario
XPPen
XPPen Artist 22R Pro Manual de usuario
