XPOtool 61479 Manual de usuario
User’s manual
Universal Wheel Bearing Tool Set
61479
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
https://www.XPOtool.com Item 61479 Page 2
The Tool Experts
04 2022-1
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler Germany
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
https://www.XPOtool.com Item 61479 Page 3
The Tool Experts
04 2022-1
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
Safety instructions
•The wheel bearing tool may only be used for its intended purpose.
Attention! When parts to be removed are loosened, the puller might spring back with the loos-
ened component thus representing a danger. Therefore, never stand behind the puller in the
direction of a possible rebound.
•Always wear personal protective equipment.
•Before each use of the wheel bearing tool, carry out a visual inspection to identify any damage
and, if necessary, replace a damaged part.
•Any part that might have been overloaded must be taken out of service immediately.
•Before straining individual threads, make sure that enough thread turns are engaged.
Scope of delivery
Name
Qty.
Name
Qty.
Adapter plate ⌀ 50 mm
1
Bushing ⌀ 83.4 mm
1
Bushing ⌀ 55 mm
1
Sleeve ⌀ 76 mm
1
Bushing ⌀ 59 mm
1
Sleeve ⌀ 86 mm
1
Bushing ⌀ 63.3 mm
1
Sleeve ⌀ 91 mm
1
Bushing ⌀ 66.6mm
1
Sleeve ⌀ 102mm
1
Bushing ⌀ 70.3 mm
1
Disassembly screw M12×1.5 (for the disas-
sembly of the wheel hub)
3
Bushing ⌀ 71.5 mm
1
Disassembly screw M14×1.5 (for the disas-
sembly of the wheel hub)
3
Bushing ⌀ 73.1 mm
1
Extracting screw 22.2 mm×300 mm
1
Bushing ⌀ 73.4 mm
1
Thrust bearing
3
Bushing ⌀ 74.8 mm
1
Screw-down nut SW 32 × 60 mm
1
Bushing ⌀ 77.5 mm
1
Pressure sleeve ⌀ 38 × 40 mm
1
Bushing ⌀ 81.5 mm
1
Pressure sleeve ⌀ 40 × 3 mm
1
https://www.XPOtool.com Item 61479 Page 4
The Tool Experts
04 2022-1
Removal
Step 1
Choose the disassembly screw depending on the wheel bolt thread – M12×1.5 or M14×1.5 – and screw
it into the thread of the wheel hub. Attention! Two points of support on the wheel bearing housing are
not necessary. Alternating support on one side of the wheel bearing housing can be done as described
in the following:
1. Turn the disassembly screw until the point of support.
2. Turn the disassembly screw one more turn.
3. Relieve the screw by turning it back.
4. Turn the wheel hub 180° until the second screw touches the point of support.
5. Proceed with the other screw in the same way as described from step 3.
Attention! Always work steadily to prevent tilting.
Step 2
Use suitable pliers to remove the retaining ring.
https://www.XPOtool.com Item 61479 Page 5
The Tool Experts
04 2022-1
Step 3
Select the appropriate sleeve according to the wheel bearing housing diameter, place it on the appro-
priate stepped plate, and select the appropriate bushing depending on the bearing diameter. In the best
case, the bushing is used with the collar pointing towards the bearing for better guidance. If the collar
does not fit easily into the inner diameter of the bearing, the washer can also be inserted with the collar
pointing towards the outside.
Step 4
The individual wheel bearing tool components are now placed on the extracting screw in the following
order:
•Thrust bearing
•Pressure sleeve
•Stepped plate
•Sleeve
Extracting screw first, insert this unit into the bearing. Now place the other side with the appropriate
bushing, pressure sleeve, and screw-down nut (with the screw-in aid first) on the extracting screw.
Attention! Check for correct fit before tightening!
Always tighten the extracting screw on the thrust bearing side and counter-hold with a wrench on the
other side.
Once the bearing has been pulled out, the complete unit can be removed from the wheel bearing hous-
ing towards the pull-out sleeve side.
Now dismantle the tool again.
https://www.XPOtool.com Item 61479 Page 6
The Tool Experts
04 2022-1
Assembly
Step 1
Mount the front circlip into the wheel bearing housing as a stop.
Step 2
Position the new bearing from behind in front of the wheel bearing housing and insert the pull-out sleeve
with the spindle into the wheel bearing housing. Attach the following pull-out parts as described under
point 4 (removal). Now the installation process can begin.
Attention! Make sure that the new bearing is positioned correctly to avoid tilting.
Step 3
After the bearing has been pulled in, the rear assembly of the extracting screw is removed again up to
the pressure sleeve in preparation for wheel hub installation and the extracting screw is pulled com-
pletely out of the axle beam. The wheel hub is now pushed onto the extracting screw in front of the
sleeve. Insert the extracting screw back into the wheel bearing housing and attach the rear pull-out parts
as usual. Now the installation of the wheel hub can begin.
https://www.XPOtool.com Item 61479 Page 7
The Tool Experts
04 2022-1
Attention! Ensure that the wheel hub is inserted cleanly and is not tilted. Finally, the rear retaining ring
is removed.
Adapter plate
The 50-mm plate is used to hold all bushings for use with a shop press.
Maintenance and care
The threads of the extracting screw and press-off bolts are exposed to high strain. All threads must be
clean and lubricated when used. The threads of the extracting screw and press-off bolts should be
lubricated with a heavy-duty grease before each use.
Important Note:
Reproduction and any commercial use (of parts) of this operating manual, requires a written permission
of WilTec Wildanger Technik GmbH.
Tabla de contenidos
Otros manuales de Herramientas de XPOtool
XPOtool
XPOtool 61313 Manual de usuario
XPOtool
XPOtool 62982 Manual de usuario
XPOtool
XPOtool 61074 Manual de usuario
XPOtool
XPOtool 62948 Manual de usuario
XPOtool
XPOtool 30156 Manual de usuario
XPOtool
XPOtool 63855 Manual de usuario
XPOtool
XPOtool 61850 Manual de usuario
XPOtool
XPOtool 62565 Manual de usuario
XPOtool
XPOtool 61910 Manual de usuario
XPOtool
XPOtool 62797 Manual de usuario
XPOtool
XPOtool 61325 Manual de usuario
XPOtool
XPOtool 62534 Manual de usuario
XPOtool
XPOtool 63323 Manual de usuario
XPOtool
XPOtool 62389 Manual de usuario
XPOtool
XPOtool 60326 Manual de usuario
XPOtool
XPOtool 61491 Manual de usuario
XPOtool
XPOtool 63393 Manual de usuario
XPOtool
XPOtool 62856 Manual de usuario
XPOtool
XPOtool 30206 Manual de usuario
