Xerox 5400N - Phaser B/W Laser Printer Manual de usuario

Service Quick Reference Guide

PHASER™ 5400

LASER PRINTER

Warning

The following servicing instructions are for

use by qualified service personnel only. To

avoid personal injury, do not perform any

servicing other than that contained in

operating instructions unless you are qualified

to do so.

This printing: August 2002

Rev. 1

721P58301

Phaser™5400

Laser Printer

Service Quick Reference Guide

Phaser 5400 Laser Printer Service Guide iii

Users Safety Summary

Terms in manual: Various terms are used throughout this manual to either provide

additional information on a specific topic or to warn of possible danger that might be

present during a procedure or action. Be aware of all symbols and terms when they are

used, and always read Note, Caution and Warning messages.

Terms on Product:

Power Source: For 110 VAC printers, do not apply more than 130 VAC RMS between

the supply conductors or between either supply conductor and ground. Use only the

specified power cord and connector. For 220 VAC printers, do not apply more than 250

VAC RMS between the supply conductors or between either supply conductor and

ground. Use only the specified power cord and connector. Refer to a qualified service

technician for changes to the cord or connector.

Warning: If the product loses the ground connection, usage of knobs

and controls (and other conductive parts) can cause an

electrical shock.

Note:A Note may indicate an operating or maintenance procedure,

practice or condition that is necessary to efficiently accomplish a

task.

A Note may also provide additional information related to a

specific subject or add a comment on the results achieved through

a previous action.

Caution:A Caution indicates an operating or maintenance procedure,

practice or condition that, if not strictly observed, could result in

damage to, or destruction of, equipment.

Warning:A Warning indicates an operating, or maintenance procedure,

practice or condition that, if not strictly observed, could result in

injury or loss of life.

Caution: A personal injury hazard exists that may not be apparent. For

example, a panel may cover the hazardous area.

Danger: A personal injury hazard exists in the area where you see the sign.

iv Phaser 5400 Laser Printer Service Guide

Power Supply and Electrical Components: Before starting any service procedure,

switch off the printer power and unplug the power cord from the wall outlet. If you must

service the printer with power applied, be aware of the potential for electrical shock.

Do not touch any electrical component unless you are instructed to do so by a service

procedure.

Mechanical Components: Manually rotate drive assemblies to inspect sprockets and

gears.

Do not try to manually rotate or manually stop the drive assemblies while any printer motor

is running.

Laser Components

Warning: This printer generates a laser beam as part of the printing

process. The laser beam is a concentrated narrow beam of

infrared light. The laser beam in this machine is invisible.

Although you cannot see the beam, it can still cause severe

eye damage. Direct eye exposure to the laser beam may

cause eye injury or blindness.

To avoid permanent eye damage, follow these directions:

■Before starting any service procedure, switch off the printer power and unplug

the power cord from the AC wall outlet.

■Do not disassemble the Raster Output Scanner Assembly (laser scanner) or any

laser component that displays a Laser Warning Sticker.

■Use caution when you are working around the Raster Output Scanner Assembly

or when you are performing laser related troubleshooting or repair procedures.

■Never place a mirror or a reflective tool or object in the laser beam path.

■Do not disassemble the printer in such a way that the laser beam can exit the

print engine during a print cycle.

S5400-01

S5400-02

Phaser 5400 Laser Printer Service Guide v

Fuser Components

Warning: This printer uses heat and pressure to fuse the toner image

to a sheet of paper. The Fuser Assembly is very hot. Switch

off printer power and wait at least 30 minutes for the Fuser

to cool before you attempt to service the Fuser Assembly or

adjacent components.

Safety Components: Make sure covers and panels are in place and that all interlock

switches are all functioning correctly after you have completed a printer service call. If

you bypass, or cheat, an interlock switch during a service call, use extreme caution when

working on or around the printer.

Warning Labels: Throughout the printer, warning labels are displayed on potentially

dangerous components. When you service the printer, check to make certain that all

warning labels are in place.

Most importantly, read and obey all posted warning labels.

Warning: Turning the power off using the On/Off switch does not

de-energize the printer. You must remove the power cord to

disconnect the printer from the main power source. Keep the

power cord accessible for removal in case of an emergency.

Safety Instructions: Read all installation instructions carefully before you plug the

product into a power source.

Care of Product: Disconnect the power plug by pulling the plug, not the cord.

Disconnect the power plug:

■If the power cord or plug is frayed or otherwise damaged,

■If any liquid or foreign material is spilled into the case,

■If the printer is exposed to any excess moisture,

■If the printer is dropped or damaged,

■If you suspect that the product needs servicing or repair, or

■Whenever you clean the product.

Ground the product: Plug the three-wire power cord (with grounding prong) into

grounded AC outlets only. If necessary, contact a licensed electrician to install a properly

grounded outlet.

vi Phaser 5400 Laser Printer Service Guide

Service Safety Summary

For qualified service personnel only: Refer also to the preceding Users Safety

Summary.

Do not service alone: Do not perform internal service or adjustment of this product

unless another person capable of rendering first aid or resuscitation is present.

Use care when servicing with power: Dangerous voltages may exist at several points in

this product. To avoid personal injury, do not touch exposed connections and components

while power is on.

Disconnect power before removing the power supply shield, soldering or replacing

components.

Do not wear jewelry: Remove jewelry prior to servicing. Rings, necklaces and other

metallic objects could come into contact with dangerous voltages and currents.

Power source: This product is intended to operate from a power source that will not apply

more then 250 VAC rms between the supply conductors or between either supply

conductor and ground. A protective ground connection by way of the grounding

conductor in the power cord is essential for safe operation.

This product is certified under IEC 825 as a Class 1 Laser Product.

CLASS 1 LASER PRODUCT

The Phaser 5400 Laser Printer is certified to comply with Laser Product Performance

Standards set by the U.S. Department of Health and Human Services as a Class 1 Laser

Product. This means that this is a class of laser product that does not emit hazardous laser

radiation; this is possible only because the laser beam is totally enclosed during all modes

of customer operation.

The laser and output of the laser scanner unit produces a beam that, if looked into, could

cause eye damage. Service procedures must be followed exactly as written without

change.

When servicing the machine or laser module, follow the procedures specified in the

manual and there will be no hazards from the laser.

Laser (FDA): Any laser label visible to service must be reproduced in the service manual

with location shown or indicated. Safe working procedures and clear warnings concerning

precautions to avoid possible exposure must also be included.

Phaser 5400 Laser Printer Service Guide vii

The Laser contained in the Phaser 5400 Laser Printer meets the following standard: Laser

class 3B, maximum 5 mW, wavelength 780 nm.

The following LASER symbol will be displayed at the start of any procedure where

possible exposure to the laser beam exists.

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

viii Phaser 5400 Laser Printer Service Guide

Federal Communications Commission Compliance

This equipment has been tested and found to comply with the limits set for a Class A

digital device, as stated in Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a commercial installation. This

equipment generates, uses, and may radiate radio frequency energy. If not installed and

used in accordance with the instructions provided, this equipment may cause disruptive

interference to nearby radio and television communications. Even if the equipment is

installed according to the instructions, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause disruptive interference to

nearby radio and television reception, switch the equipment off to determine if it is the

true cause of the interference. If the equipment is the cause of the interference, the user

should try to minimize the interference by taking one or more of the following courses of

action:

■Either re–orient or relocate the radio/television receiving antenna.

■Increase the separation between the equipment and the radio/television receiver.

■Connect the equipment to an AC outlet that is not on the same circuit as the

radio/television receiver.

■If the previous solutions fail to bring results, you should consult either your equipment

dealer or an experienced radio/television technician.

For more information on interference, refer to the Federal Communications Commission’s

booklet “How to Identify and Resolve Radio-TV Interference Problems”. This booklet is

available from the U.S. Government Printing Office, Washington D.C. 20402, Stock No.

004-000-00345-4.

Phaser 5400 Laser Printer Service Guide ix

Canadian Notice

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus as described in the radio interference regulations of the Canadian

Department of Communications.

Avis Canadien

Cet appareil numerique est conforme aux limites émission de bruits radioélectriques pour

les appareils de classe A stipulés das le réglement sur le brouillage radioéletrique du

Ministére des Communcations du Canada.

European Notice

This equipment was tested and is determined to be compliant with VDE requirements for a

Class A device.

Hinweis

Hiermit wird bescheinigt, dass der Babe Laserdrucker, in bereinstimmung mit den

Betimmunngen der Vfg 104ß 984 funkenstört ist. Der Deutschen Bundespost wurde das

Inverkehrbringen dieses Gertëes angqeigt und die Berechtigung zur berprufung der Serie

auf Einhaltung der Bestimmungen eingeräumt.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora de Xerox

Xerox

Xerox Phaser 8560 Manual de usuario

Xerox

Xerox DocuPrint NC60 Manual de servicio

Xerox

Xerox Phaser 8400 Manual de usuario

Xerox

Xerox Phaser 8400 Manual de usuario

Xerox

Xerox Phaser 200I Manual de usuario

Xerox

Xerox Phaser 860 Manual de usuario

Xerox

Xerox WorkCentre Pro C2128 Manual de usuario

Xerox

Xerox Phaser 6180 Manual de usuario

Xerox

Xerox 6360V_DN Manual de usuario

Xerox

Xerox DocuPrint P1210 Manual de usuario

Xerox

Xerox DocuPrint N24 Manual de usuario

Xerox

Xerox Phaser 7300DN Manual del propietario

Xerox

Xerox C310 Manual de usuario

Xerox

Xerox 495 Manual

Xerox

Xerox DocuColor 1632 Instrucciones de montaje

Xerox

Xerox Phaser 6120 Manual de usuario

Xerox

Xerox Phaser 6360 Manual de usuario

Xerox

Xerox AltaLink C80 Series Manual del propietario

Xerox

Xerox 2000 Manual de usuario

Xerox

Xerox DocuPrint C2428 Manual de usuario

Xerox

Xerox PHASER 7500 Instrucciones de uso

Xerox

Xerox 4050 Manual técnico

Xerox

Xerox 6000V_B Manual de usuario

Xerox

Xerox Nuvera 100 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario