Xerox DC230LP Instrucciones de uso
7+('2&80(17&203$1<
DC230LP Windows NT®4.0 TCP/IP Quick Install
Page 1 of 4
2. Access the System Administration menus:
a)
Press [Online] to take the printer off
line. displays.
b)
Press [Menu]. displays.
c)
Press [], then press []or []until
displays.
d)
Press []. displays.
e)
Use the []and []keys to enter
[2222].
Note: 2222 is the factory default password and
may be changed to suit your needs. Refer to the
DC230LP System Administration Guide,
Network Installation and Troubleshooting
.
f)
Press [Enter]. displays.
3. Access the TCP/IP menus:
a)
Press []. displays.
b)
Press []until
displays.
c)
Press []. displays.
Printer Off Line
Main Menu >
System
Administration >
Enter Password >
System Admin >
Port Setup >
Network Setup >
TCP/IP >
d)
Press []. displays.
4. IP Address Setup (skip this step if using
RARP):
a)
Press []. displays.
Note: Use zeros to supplement each address
segment if fewer than 3 digits are used; e.g.,
13.252.25.08 = 013.252.025.008.
b)
Use the []or []key to enter the
first digit of the IP Address.
c)
Press []to move to the next digit.
Repeat this procedure to enter the
entire IP Address.
d)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
5. RARP Setup:
Note: If you used a static IP Address, leave the
RARP setting at
Disabled
.
a)
To change the RARP setting, press
[]until the current setting displays
.
IP Address
(current entry)
>
IP Address =
(current entry) *
IP Address
(your entry)
>
RARP
(current entry)
>
Over
Installation Requirements:
To install the DC230LP in a DHCP environment,
exclude the addresses assigned to the
DC230LP at the DHCP server.
Before Installation:
Record the following information for use during
setup at the DC230LP:
TCP/IP Address:________________________
Gateway Address: ______________________
Subnet Mask: __________________________
Broadcast Address: _____________________
Host Name:____________________________
This installation procedure assumes that you
know how to navigate through the menu system
on the DC230LP Control Panel. Refer to the
quick reference card,
Using the Menu System,
(701P96834) for assistance.
1. Connect the DC230LP to your network
outlet or cable.
For assistance, contact your local Xerox Customer Support Center:
USA: 1-800-821-2797 Canada: 1-800-939-3769
7+('2&80(17&203$1<
DC230LP Windows NT®4.0 TCP/IP Quick Install
Page 2 of 4
e)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
7. Enter the Subnet Mask:
a)
Press []until
displays.
b)
Press []. displays.
c)
Use the []or []key to select the
first digit of the Subnet Mask for your
network.
d)
Press []to move to the next digit.
Repeat this procedure to enter the
entire Subnet Mask.
e)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
8. Enter the Broadcast Address:
Note: Broadcast Address is where all the host
bits are set to either zeros (0) or ones (1).
Default Gateway
(your entry)
>
Subnet Mask
(current entry)
>
Subnet Mask =
(current entry)
Subnet Mask
(your entry)
>
a)
Press []until
displays.
b)
Press []. displays.
c)
Use the []or []key to select the
first digit in the Broadcast Address.
d)
Press []to move to the next digit.
Repeat procedure to enter the entire
Broadcast Address.
e)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
9. Enter the Printer (Host) Name:
Note: It is recommended that the Printer (Host)
Name be the same as your Share Name.
a)
Press []until
displays.
b)
Press []. displays.
c)
Press []repeatedly until the cursor
reaches the last character. A tone
sounds indicating when the last
character has been reached.
Broadcast Addr
(current entry)
>
Broadcast Addr =
(current entry)
Broadcast Addr
(your entry)
>
Printer Name
(current entry)
>
Printer Name =
(current entry)
b)
Press []. displays.
c)
Press []until the required setting
displays .
d)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
6. Enter the Gateway Address:
a)
Press []until
displays.
b)
Press []. displays.
Note: Use zeros to supplement each address
segment if fewer than 3 digits are used; e.g.,
13.252.25.08 = 013.252.025.008.
c)
Use the []or []key to select the
first digit in the Gateway Address.
d)
Press []to move to the next digit.
Repeat this procedure to enter the
entire Gateway Address.
RARP =
(current entry) *
RARP =
(required entry)
RARP
(your entry)
>
Default Gateway
(current entry)
>
Default Gateway =
(current entry)
7+('2&80(17&203$1<
DC230LP Windows NT®4.0 TCP/IP Quick Install
Page 3 of 4
d)
Press []repeatedly to delete the
current entry.
e)
Use the []or []key to select the
first character in the Printer Name.
f)
Press []to move to the next charac-
ter. Repeat this procedure to enter the
entire Printer Name.
g)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
10.Enable the Line Printer Daemon (LPD):
a)
Press [Escape] to move back a level
in the menu system.
displays.
b)
Press []until
displays.
c)
Press []. displays.
d)
Press []. displays.
e)
Press []until
displays.
Printer Name
(your entry)
>
TCP/IP
-
>
Line Printer
Daemon >
Enablement
(current entry)
>
Enablement =
(current entry)
*
Enablement =
Enabled
f)
Press [Enter]. **SAVED** displays
momentarily, followed by
.
Note: The next menu at this level,
Port Setting
,
has a fixed setting for the LPD (515) and can not
be changed.
11. Save all settings:
a)
Press [Online].
displays.
b)
Press [Enter].
displays. The DC230LP will reboot,
save the settings entered, and print a
Configuration Report in approximately
3 minutes.
12.Check the settings on the Configuration
Report against those entered to be sure
they are correct.
Enablement
Enabled >
Reset Required
Press ENTER key
Warming Up
Please Wait . . . >
13.At the client, install print drivers and map
the printer in the usual manner. Refer to
the CentreWare®manual,
Getting Started
with Print and Fax Services
, for additional
information.
14.TCP/IP protocol and TCP/IP print services
must be installed on the NT Server and the
printer name must be set to [lp] (lower
case) when configuring the LPR port.
Refer to the screen sample below.
Additional information on the Windows NT
TCP/IP setup can be found in the
DC230LP
System Administration Guide, Network Installa-
tion and Troubleshooting
.
7+('2&80(17&203$1<
DC230LP Windows NT®4.0 TCP/IP Quick Install
Page 4 of 4 ©1998 Xerox Corporation
701P98454 Version 1.0, 5-98
Otros manuales de Impresora todo en uno de Xerox
Xerox
Xerox WorkCentre XE90 Manual de usuario
Xerox
Xerox PHASER 8560MFP Manual de usuario
Xerox
Xerox C8130 Manual de usuario
Xerox
Xerox VersaLink B7025 Manual de lista de piezas
Xerox
Xerox DocuColor 1632 Manual de usuario
Xerox
Xerox WORKCENTRE C2424 Manual de usuario
Xerox
Xerox Document Centre 425 Manual de usuario
Xerox
Xerox WorkCentre 5687 Series Manual de usuario
Xerox
Xerox WorkCentre 6027 Manual de funcionamiento
Xerox
Xerox ColorQube 9201 Manual del propietario
Xerox
Xerox WorkCentre 3655 Manual de usuario
Xerox
Xerox Fiery EXP4110 Especificaciones
Xerox
Xerox Phaser 5500 series Manual del operador
Xerox
Xerox Phaser 3610 Manual de usuario
Xerox
Xerox WorkCentre 3215 Manual de funcionamiento
Xerox
Xerox WorkCentre BookMark 40 Manual de usuario
Xerox
Xerox PHASER 8560MFP Manual de usuario
Xerox
Xerox WorkCentre 5845 Manual de usuario
Xerox
Xerox WorkCentre 5020 Manual de operación y mantenimiento
Xerox
Xerox VersaLink B615 Manual de usuario
Manuales populares de Impresora todo en uno de otras marcas
Triumph Adler
Triumph Adler DC 2016 Manual
Epson
Epson WorkForce WF-2510 Guía del usuario
Epson
Epson Stylus Scan 2000 Manual de instalación y operación
Epson
Epson PictureMate Snap PM 240 Manual de instrucciones
Konica Minolta
Konica Minolta bizhub C35 Manual de usuario
Brother
Brother MFC-J430w Manual de usuario
