Xante CL30 Manual de usuario
__________________________________________ Heavy Stock Enabled CL30 Addendum v3 1
10/19/04 v3
Congratulations! With your new,innovative XANTÉ Heavy Stock Enabled CL30,you now can print
on heavy weight media up to 330 g/m2.
Multi-Purpose Tray
Themulti-purpose tray handles from 176 g/m2(8point) up to330 g/m2(16 point) media. Sheet
capacity varies depending upon the media’s thickness; for example, you can load 15 sheets of 14 point
stock.Normally,you can load up to 25 sheets of heavier stock;however,if you run sheets under 175
g/m2thickness,you may need to feed the sheets one at a time from this tray or use the cassette tray.
The following list covers common heavy stock medias that the multi-purpose tray is able to handle.
Also,a full paper conversion chart is available on XANTÉ’s web site (www.xante.com/paper).
• 97 lb. Index to 200 lb.Index
• 65 lb. Cover to 130 lb.Cover
• 8 Point to 16 Point
• 176 g/m2to 330 g/m2
Normal manufacturing tolerances can be ±5 to 7%. For this reason,g/m2is the most accurate way to
measure paper weight.
2 Heavy Stock Enabled CL30 Addendum v3 _________________________________________________
To load media in the multi-purpose tray
1. Open the multi-purpose tray and extend the paper feed guides (fig. 1).
Fig. 1 Open the Multi-Purpose Tray Fig. 2 Open the Straight-Through Paper Exit
2. Load the media print side up in the multi-purpose tray and adjust the paper guides to the size of
the media being used.
Make sure the media stack does not exceed the multi-purpose tray’s media full line.
3. Open the straight-through paper exit (fig. 2) and extend the paper supports.
Always use the straight-through exit path for heavy stock printing.Make sure the straight-through
paper exit is open and the paper supports are extended (fig. 2).
To prevent media jams in the multi-purpose tray
• Don’t leave space between the media and the paper guides.
• Do not over fill the tray. Capacity depends on the media’s type and weight.
• Do not load damaged media or media of different sizes,quality,or thickness at the same time.
• Do not open or close the rear paper exit while printing.
• Fan paper to separate the sheets.
Once media is loaded into the multi-purpose tray, you need to configure the printer for ultra heavy
media.See your printer user’s manual for details.
Light Media Weight
The light media weight settings begin at 24 lb.US Bond (90 g/m2).
Consumables
The consumable ratings for the Heavy Stock Enabled XANTÉ CL30 consumables are as follow:
• Transport Belt—30,000 letter size prints
• Drum—15,000 letter size prints,5% coverage prints
• Toner Cartridge—15,000 letter size,5% coverage prints
• Heavy Stock FeedAssembly—42,000 letter/A4 size prints
• CL30 HSE Fuser only (not a standard CL30 fuser)—30,000 letter size prints.
Use only a CL30 HSE fuser for your printer—not a standard CL30 fuser.The HSE fuser is available in
110 and 220 volt models; make sure to use the correct fuser model. The 110 volt model part number is
200-100169-HS; the 220 model part number 200-100170-HS.
To order these consumables,contact your preferred XANTÉ dealer or call your XANTÉ Consumables
Sales Representative at 800-540-7091.
__________________________________________ Heavy Stock Enabled CL30 Addendum v3 3
Engine Life
The rating for the engine life of the XANTÉ Heavy Stock Enabled CL30 is 1,000,000 prints or 5 years,
whichever comes first.
Maintenance
Preventing Media Jams
To help prevent media jams in the multi-purpose tray, use a can of compressed air to clean the rollers
by blowing off any accumulated dust or debris (fig. 3).
Always wear protective eyeware when using compressed air to prevent injuries.
Rollers
Fig. 3 Clean the Rollers
Other Maintenance
For other basic maintenance procedures such as moving the printer, adding paper,or changing an
image drum,transfer belt, or fuser unit,refer to the“Maintenance”chapter in your printer’s User’s
Guide.
◊◊◊
XANTÉ’s web page at www.xante.com contains a Support section where you can download printer drivers, software,PPDs,
manuals,and other technical information.The FAQ section answers the most frequently asked questions about each product.
Technical Support 800-926-8393 (US and Canada) Consumables: 800-540-7091 (US/Canada)
7A.M. - 6 P.M.CST Fax: 251-473-6503
Mon. - Fri. Other areas: call your XANTÉ vendor
XANTÉ®is a registered trademark of XANTÉ CORPORATION. All other brand and product names are trademarks,
registered trademarks, or service marks of their respective holders.
Otros manuales para CL30
4
Tabla de contenidos
Otros manuales de Impresora de Xante
Xante
Xante ColourLaser series guide Manual de usuario
Xante
Xante Accel-a-Writer 812 Manual de usuario
Xante
Xante FilmMaker 4 Manual de usuario
Xante
Xante Accel-a-Writer 812 Manual de usuario
Xante
Xante Accel-a-Writer 8200 Instrucciones de funcionamiento
Xante
Xante Impressia Manual de usuario
Xante
Xante Accel-a-Writer 8200 Manual de usuario
Xante
Xante IDT 79RC3255 processor Manual de usuario
Xante
Xante CL30 Manual de servicio
Xante
Xante Accel-a-Writer 8200 Manual de usuario
Xante
Xante Assel-a-Writer-8300 Manual de usuario
Xante
Xante ScreenWriter 3 Manual de usuario
Xante
Xante Accel-a-Writer 3 Series Manual de usuario
Xante
Xante ColourLaser series guide Manual de usuario
Xante
Xante Accel-a-Writer 8300 Manual de referencia
Xante
Xante Accel-a-Writer 8200 Manual de usuario
Xante
Xante Accel-a-Writer Accel-a-Writer 3DN Manual
Xante
Xante FilmMaker 4 Manual de usuario
Xante
Xante Accel a Writer 812 Manual de usuario
Xante
Xante AW 1200 Manual de usuario
