X-Taste X250 Manual de usuario
1
X250
User Manual
2
The X250 is designed for professional vapers. To ensure safety and
proper usage of the device please read the instruction carefully.
It is prohibited to open body of the device otherwise warranty will
be void.
Do not expose device to heat source for long period. It might
damage the battery.
Warning: Abnormal operation may damage the device!
This product is strictly for above 18 years only.
Open Box (Basic configuration):
1. 1x X250 device
2. 1x 1350mAH replaceable LIPO battery
3. 1 x USB cable (support up to 2A)
4. 1 x user manual
3
1. Specification and features
Model: X250
Dimension: Height x Width x Length (102mmx63mmx27mm)
Weight: TBD
Body Material: Zinc Alloy
Atomizers Connector: Stainless Steel 510 Connection, Nickel Plated Brass Contact
Display: 1.3 OLED
Easy replaceable 1350mAh 2 Cell LIPO
o7.4V
oEasy replaceable battery
oNote Only support battery from authorize dealer of X-Taste
Atomizers
oOutput power range: 5W ~ 250W
oOutput current range: 0A ~ 45A
oMaximum 40A continuous current. *2
oOutput voltage range: 0.5V ~ 15.5V (Buck-Boost DC-DC converter)
Power consumption (Without fire): 0.4W
Very low standby current: 39.5uA (Able to standby 3.9 years for fully charge battery)
Coil resistance
oMeasurement range 0.04Ohm ~ 10Ohm
oResolution: 1m Ohm (based on 0.1ohm measurement)
Power control mode
oRecommended resistance range: 0.08Ohm~3Ohm
oCoil over heat protection. Refer to coil material table for detail.
Temperature control mode
oRecommended resistance range: 0.08Ohm~2Ohm
oRepeatability: 1 degree Celsius / 1.8 Fahrenheit
oSupport Ni-200, Ti 01/02, SS316L, NiFe30, NiFe70. Refer to coil material table for
detail.
oTemperature adjustment range can be change through “X-Taste Advance”.
oDry coil protection.
Power control / Temperature control mode
Efficiency: 98% for Kanthal A1, >94% for Ni-200 (200W) *1
Battery Management
oSupport maximum up to 2A USB charging current.
oLess than 2 hour for complete charging based on 2.0A USB current.
oSupport cell by cell monitoring
oSupport cell balancing: 99.5%
4
Safety feature
oDry coil protection (only applicable for temperature control mode)
oCoil overheat protection
Support Ni200, Ti01/02, SS316L, NiFe30, NiFe70, Nichrome N60. Refer to coil
material table for detail.
Protection temperature can be change through “X-Taste Advance”.
oReal-time battery temperature monitoring. Auto shutdown device if temperature
too high or too low.
oReal-time on-board temperature monitoring. Auto shutdown device if temperature
too high.
oBattery health condition checking feature. Able to give alert if battery not in good
condition.
oCoil over voltage protection.
oCoil over current protection.
oCoil short/open circuit protection.
oWeak battery protection.
oBattery over charge protection.
oBattery over load protection.
o10 seconds maximum fire duration protection.
Support firmware upgrading through USB port.
Screen lock features.
Coil resistance measurement features.
Real-time display data during fire on
oBattery voltage, capacity
oCoil resistance (power mode)
oSensing coil temperature (temperature mode)
oCoil voltage
Auto power off features, 90 seconds.
oCan be modifying through “X-Taste Advance”.
5 individual preset configurations.
Continuous short press “Fire ON”button 3 times to power on devices.
Smart auto lock coil resistance.
Using TCR or temperature coefficient based on type of coil material for more precise
temperature control and coil overheats protection.
X-Taste Advance software allow user to modify setting and operation of the device.
*1 Based on average measurement result at certain test condition.
*2 Max current might vary depend to battery.
5
Coil Material Table:
Coil Material
Overheat protection
*3
Temperature Control
Range *3
Temperature Control
Resolution
Ni200
300 Degree C
572 Fahrenheit
100~285 Degree C
212~545 Fahrenheit
1 Degree C
1 Fahrenheit
Ti01/Ti02
280 Degree C
536 Fahrenheit
100~265 Degree C
212~509 Fahrenheit
1 Degree C
1 Fahrenheit
NiFe30 (Stealth Vape)
300 Degree C
572 Fahrenheit
100~285 Degree C
212~545 Fahrenheit
1 Degree C
1 Fahrenheit
NiFe70
300 Degree C
572 Fahrenheit
100~285 Degree C
212~545 Fahrenheit
1 Degree C
1 Fahrenheit
SSL316L
300 Degree C
572 Fahrenheit
100~285 Degree C
212~545 Fahrenheit
1 Degree C
1 Fahrenheit
Nichrome N60
300 Degree C
572 Fahrenheit
NA
NA
Kanthal A1
NA
NA
NA
Active Region Table:
*3 Wrong configuration of coil material type may cause overheat protection and temperature control not
working properly.
6
2. Structure Diagram
Fire Button
“^”Button
“v”Button
7
3. Operation (Power Up Device)
-Short press “Fire”button 3 times to power up devices.
-This design is to avoid “fire”being trigger accidently.
-Device auto enter power off mode after 60 seconds of idling.
4. Operation (Coil Resistance measurement)
-Press “^”+ “v”for coil resistance measurement.
Firmware version
8
5. Operation (Power mode)
-Long press “v”button to trigger adjust target power. Press “^”to increase and “v”to
decrease power. Press “fire”button to confirm the power setting.
-Short press “^”to switch different fire mode (soft, standard, powerful)
-Long press “^”to enter main menu.
-Short press “v”to switch different preset memory setting.
-Press “^”+ “v”for coil resistance measurement.
-Press “fire”button to start fire.
-Under “MENU/Control”select “Wattage”to enter power mode.
-Fire mode “Powerful”giving 10% more power than “Standard “mode configuration.
-Fire mode “Soft”giving 10% less power than “Standard”mode configuration.
Target power
Preset memory
Coil material
Fire mode: Soft, Standard, Powerful
Elapsed time
Measured coil voltage, V
Measured coil
resistance, ohm
Battery capacity
and voltage.
9
6. Operation (Temperature mode)
-Long press “v”button to trigger adjust starting power. Press “^”to increase and “v”to
decrease power. Press “fire”button to confirm the power setting.
-Short press “^”button to trigger adjust temperature. Press “^”to increase and “v”to
decrease temperature. Press “fire”button to confirm the temperature setting.
-Long press “^”to enter main menu.
-Short press “v”to switch different preset memory setting.
-Press “^”+ “v”for coil resistance measurement.
-Press “fire”button to start fire.
-Under “MENU/Control”select “Temp”to enter temperature mode.
-Example of Ni 200, Target temperature 275 degree C, Starting power 250W
Starting power
Preset memory
Coil material
Temperature control mode
indicator
Elapsed time
Measured coil voltage, V
Measured coil
resistance, ohm
Battery capacity
and voltage.
Target/measured
temperature
10
7. Operation (Main Menu)
-Press “v”,”^”to select menu setting.
-Press “fire”button to enter sub menu.
8. Operation (Main Menu / Control)
-Press “v”,”^”to switch menu setting.
-Press “fire”button to confirm control mode setting.
Coil type selection
Control mode
Battery health checking
Temperature unit
(Degree C or F)
Power off device
Exit main menu
Power mode
Preset memory
Temperature mode
Tabla de contenidos
Otros manuales de Cigarrillo electrónico de X-Taste
Manuales populares de Cigarrillo electrónico de otras marcas
STEAMAX
STEAMAX TFV8 X-BABY Manual de usuario
iQOS
iQOS 3 MULTI Manual de usuario
Vaporesso
Vaporesso LUXE XR MAX Manual de usuario
ZAZO
ZAZO PRO Mini 2 Manual de usuario
Aquafog
Aquafog Turbo XE Manual
Electronic Cigarettes Australia Pty Ltd
Electronic Cigarettes Australia Pty Ltd AUSSIE BLUE ENDURANCE Manual de usuario
