wtw LR 325/01 Manual de usuario
ba55303e05 01/2009
LR 325/01
Operating manual
Ultrapure water conductivity cell
LR 325/01
ba55303e05 01/2009
Accuracy when
going to press The use of advanced technology and the high quality standard of our
instruments are the result of continuous development. This may result in
differences between this operating manual and your instrument. Also, we
cannot guarantee that there are absolutely no errors in this manual.
Therefore, we are sure you will understand that we cannot accept any legal
claims resulting from the data, figures or descriptions.
Copyright ©Weilheim 2009, WTW GmbH
Reprinting - even as excerpts - is only allowed with the explicit written
authorization of WTW GmbH, Weilheim.
Printed in Germany.
LR 325/01 Inhaltsverzeichnis
11
ba55303e05 01/2009
LR 325/01 - Contents
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.1 Structure and function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.2 Recommended fields of application . . . . . . . . . . . . . . . . . . . . 12
2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3 What to do if... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Overview LR 325/01
12 ba55303e05 01/2009
1Overview
1.1 Structure and function
Structure
1.2 Recommended fields of application
Measurements in ultapure water.
2 Cleaning
CAUTION
Before cleaning, disconnect the sensor from the instrument.
Cleaning A thorough cleaning is particularly recommended for measurements of low
conductivities.
After cleaning, thoroughly rinse with deionized water and recalibrate if
necessary.
Aging of the
conductivity
measuring cell
Normally, the conductivity measuring cell does not age. Special measuring
media (e.g. strong acids and lyes, organic solvents) or too high temperatures
shorten the operational lifetime considerably or damage the measuring cell.
The warranty does not cover cases where such conditions cause failure or
mechanical damage.
Disposal We recommend to dispose of the conductivity cell as electronic waste.
1Shaft
2Connection head
21
Contamination Cleaning procedure
Lime sediments Immerse in acetic acid for 5 minutes
(volume share = 10 %)
Fat/oil Clean with warm water that contains
washing-up liquid
LR 325/01 What to do if...
13
ba55303e05 01/2009
3 What to do if...
Error symptom Cause Remedy
No temperature or
conductivity display
– No connection between
measuring instrument and sensor
– Cable defective
– Check connection between
measuring instrument and sensor
Measurement delivers
implausible conductivity
values
– Incorrect cell constant adjusted at
the measuring instrument
– Measuring range exceeded
– Contamination in the area of the
electrodes
– Electrodes damaged
– Check / correct the cell constant
– Observe the application range
– Clean the sensor (see section 2).
– Return the sensor
Incorrect temperature
display
– The temperature sensor was not
immersed deep enough in the
measuring solution
– Temperature sensor defective
– Observe the minimum immersion
depth
– Return the sensor
Technical data LR 325/01
14 ba55303e05 01/2009
4 Technical data
General features Measuring principle Two-electrode measurement
Cell constant 0.100 cm-1 ±2 %
Temperature sensor integrated NTC 30 (30 k:at 25 °C / 77 °F)
Dimensions
(in mm)
Weight approx. 135 g
Materials Shaft Stainless steel 1.4571
Connection head POM
Conductivity electrodes Stainless steel 1.4571
Thermistor enclosure Stainless steel 1.4571
Connection cable Lengths 1,5 m
Diameter 6 mm
Smallest allowed
bend radius
fixed installation: 50 mm
flexible use: 80 mm
Plug type Socket, 8 pins
Pressure
resistance Sensor with closed plug
connection
IP 68 (2 x 105Pa or 2 bar)
Cable plug IP 67 (when plugged in)
The LR 325/01 meets the requirements according to article 3(3) of the
97/23/EC directive ("Pressure equipment directive").
120,0
165
12,0 17,5
LR 325/01 Technical data
15
ba55303e05 01/2009
Pin assignment
Measurement
conditions Conductivity measuring
range
0.001 µS/cm ... 200 µS/cm
Temperature range -5 ... 80 °C (100 °C)
23 ... 176 °F (212 °F)
Max. allowed overpressure 2 x 105Pa (2 bar)
Minumum depth of immer-
sion
30 mm
Maximum depth of
immersion
(at temperature)
Whole sensor + cable up to 80 °C (176 °F)
Sensor shaft only (=120 mm) up to 100 °C
(212 °F)
Operating position any
Storage
conditions Recommended storing
method
in air
Storage temperature 0 ... 50 °C (32 ... 122 °F)
Characteristic data
on delivery Temperature responding
behavior
t99 (99 % of the final value after) < 20 s
Precision of the temperature
sensor
±0.2K
4
2
5
3
NTC
NTC
Shield
not used
Plug from the front: 4
5
7
38
2
6
1
4
2
5
3
8
6
1
7
NTC
30 k
Outer electrode
Inner electrode
Technical data LR 325/01
16 ba55303e05 01/2009
Tabla de contenidos
Otros manuales de Accesorios de wtw
wtw
wtw TetraCon 700 IQ Manual de usuario
wtw
wtw MIQ/TC 2020 XT Manual de usuario
wtw
wtw FDO 700 IQ F Manual de usuario
wtw
wtw visoturb 700 iq Manual de usuario
wtw
wtw DIQ/S 282 Manual de usuario
wtw
wtw visoturb 700 iq Manual de usuario
wtw
wtw MultiLine FDO 925 Manual de usuario
wtw
wtw VARiON Plus 700 IQ Manual de usuario
wtw
wtw CN 500 DIN Manual de usuario
wtw
wtw TriOxmatic 690 Manual de usuario
wtw
wtw MIQ/2-PR Manual de usuario
wtw
wtw NitraLyt 700 IQ Manual de usuario
wtw
wtw NiCaVis 701 IQ NI Manual de usuario
wtw
wtw NitraVis 70 IQ TS Series Manual de usuario
wtw
wtw NitraLyt Plus 700 IQ Manual de usuario
wtw
wtw Stirrox G Manual de usuario
wtw
wtw AmmoLyt 700 IQ Manual de usuario
wtw
wtw ConOx Manual de usuario
wtw
wtw visoturb 700 iq Manual de usuario
wtw
wtw FDO 700 IQ Manual de usuario
