Worx Wx570 Manual de usuario

WX570

P07

P17

P27

P37

P47

P57

P67

P77

P86

P95

P104

P113

P122

P132

FIN

NOR

Multi-function saw

Multifunktionssäge

Scie multifonction

Sega multifunzione

Sierra multiusos

Serra multifuncional

Multifunctionale zaag

Multi-funktionssav

Monitoimisaha

Multifunksjonssag

Multifunktionssåg

Çok fonksiyonlu testere





Original instructions EN

Übersetzung der Originalanleitung D

Traduction des instructions initiales F

Traduzione delle istruzioni originali I

Traducción de las instrucciones originales ES

Tradução das instruções originais PT

Vertaling van de oorspronkelijke instructies NL

Oversættelse af de oprindelige instruktioner DK

Alkuperäisten ohjeiden käännös FIN

Oversettelse av de opprinnelige instruksjonene NOR

Översättning av originalinstruktionerna SV

 TR

 GR

 RU

18 19 20

A1 A2 A3

B4 B5 C1

B1 B2 B3

C2 D1 D2

E F G

J K L

H I1 I2

M N 0

Q R

E F G

J K L

H I1 I2

M N 0

Q R

Multi-function saw EN

1. OFF SWITCH

2. ON SWITCH

3. CARRY HANDLE

4. BLADE RELEASE FINGER PULL

5. BLADE GUIDE ROLLER (See Fig. A2)

6. PRESSURE FOOT

7. QUICK RELEASE LEVER FOR PRESSURE FOOT

8. SUPPORT ARM

9. GUARD ARM CLAMP KNOB

10. GUARD ARM

11. VACUUM PORT

12. FENCE SLOT

13. TABLE INSERT

14. MITER SLOT

15. BLADE STORAGE DRAWER

16. VARIABLE SPEED CONTROL

17. DUST COLLECTION DRAWER

18. MITER GAUGE STORAGE

19. MITER GAUGE/RIP FENCE

20. RIP FENCE LOCKING KNOB

21. MITER GAUGE ANGLE LOCKING KNOB

22. MITER GAUGE/RIP FENCE SLIDING FACE

23. SLIDING FACE LOCKING KNOBS

24. CORD WRAP

*Not all the accessories illustrated or described are included in standard delivery.

Multi-function saw EN

TECHNICAL DATA

Type WX570 (5-designation of machinery, representative of saw)

Voltage 230-240V~50/60Hz

Power 650W

No load speed 800-2800/min

Cutting capacity

Wood 40mm

PVC pipe 30mm

Aluminum 10mm

Steel 3mm

Tile 10mm

Stroke length 22mm

Blade shank T-shank

Blade length 100mm or less

Table size 400mm×430mm

Protection class /II

Weight 8kg

NOISE INFORMATION

A weighted sound pressure LPA 82dB(A)

A weighted sound power LWA 95dB(A)

KPA&KWA 3dB(A)

Wear ear protection when sound pressure is over 80dB(A)

Multi-function saw EN

ACCESSORIES

Miter gauge 1

Allen key 1

Blades:

Wood cutting blade 2

Aluminum cutting blade 1

Steel cutting blade 1

Tile cutting blade 1

Scrolling blade 1

Blade grip 1

Vacuum adapter 1

We recommend that you purchase your accessories from the same store that sold you the tool.

Use good quality accessories marked with a well-known brand name. Choose the type according

to the work you intend to undertake. Refer to the accessory packaging for further details. Store

personnel can assist you and offer advice.

Multi-function saw EN

ADDITIONAL SAFETY

INSTRUCTIONS FOR YOUR

BladeRunner®

1. SAFETY PRECAUTION

1) Do not use saw blades which are damaged

or deformed;

2) Replace the table insert when worn;

3) Connect band saw to a dust-collecting

device when sawing wood;

4) Take care that the selection of the saw

blade and the speed depends on the

material to be cut;

5) Do not clean the saw blade whilst it is in

motion;

Wear suitable personal protective equipment,

when necessary, this could include:

– Hearing protection to reduce the risk of

induced hearing loss;

– Respiratory protection to reduce the risk of

inhalation of harmful dust;

– Gloves for handling the saw band and

rough material.

2. SAFE OPERATION

1) During transportation the saw band guard

should be locked at fully down (close to the

table) position;

2) Do not use guard and its support system

for handling or transportation;

3) When cutting round timber use a suitable

holding device to prevent twisting of the

workpiece;

4) Any time after cutting, the knob for locking

blade guard shall be released so that the

guard is fully down to the table.

A GLOSSARY OF TERMS

1. CROSSCUT

A cutting or shaping operation made across

the width of the work piece cutting the work

piece to length.Typically the cut is across the

wood grain.

2. RIPPING OR RIP CUT

A cutting operation along the length of the

work piece cutting the work piece to width.

Typically the cut is along the wood grain.

3. MITER CUT

A cutting operation made with the work piece

at any angle to the blade other than 90°.

CROSS CUT

RIP CUT

MITER CUT

Tabla de contenidos

Idiomas:

Otros manuales de Sierra de Worx

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario

Worx wx570 Manual de usuario

Manuales populares de Sierra de otras marcas