woodmizer Edger Multirip Manual de usuario
Edger Multi-Rip
Safety, Operation, Maintenance
& Parts Manual
EG300E20S-EMR rev.A1.03
(EE20S-EMR) rev. A1.03
EG300E25S-EMR rev. A1.03
(EE25S-EMR) rev. A1.03
Safety is our #1 concern! Read and understand
all safety information and instructions before oper-
ating, setting up or maintaining this machine.
June 2009
Form #907
!
2 EGdoc091010Table of Contents
Table of Contents Section-Page
SECTION 1 SERVICING THE EDGER 1-1
1.1 If You Need To Order Parts ...................................................................1-1
1.2 Customer and Edger Identification.........................................................1-1
1.3 If You Need Service...............................................................................1-2
1.4 Edger Components .................................................................................1-2
SECTION 2 SAFETY 2-1
2.1 Safety Symbols.......................................................................................2-1
2.2 Safety Instructions..................................................................................2-1
SECTION 3 OPERATION 3-1
3.1 Pre-Operation Check..............................................................................3-1
3.2 Control Overview...................................................................................3-3
3.3 Edger Setup ............................................................................................3-4
3.4 Machine Start..........................................................................................3-6
3.5 Blade Installation....................................................................................3-8
3.6 Edging Lumber.....................................................................................3-13
SECTION 4 SETWORKS OPERATION 4-1
4.1 Edger Controller Panel...........................................................................4-1
4.2 Start-up settings of the controller...........................................................4-2
4.3 Operation, Memory Buttons (A, B, C, D, E)..........................................4-5
SECTION 5 MAINTENANCE & ALIGNMENT 5-1
5.1 Changing the Blades...............................................................................5-1
5.2 Tensioning the Belts...............................................................................5-3
5.3 Tensioning the Chains............................................................................5-4
5.4 Checking the Rollers ..............................................................................5-6
5.5 Lubrication .............................................................................................5-6
5.6 Maintaining and Sharpening Anti-Kickback Fingers.............................5-7
5.7 Alignment...............................................................................................5-7
5.8 Blade Sharpening..................................................................................5-10
5.9 Using the Blades...................................................................................5-11
SECTION 6 SPECIFICATIONS 6-1
6.1 Overall Dimensions................................................................................6-1
6.2 Multirip Edger Specifications.................................................................6-2
6.3 Electrical Diagram..................................................................................6-4
6.4 Electrical Component List......................................................................6-6
6.5 Dust Extractor Specifications.................................................................6-7
Table of Contents Section-Page
Table of Contents EGdoc0910103
SECTION 7 PARTS 7-1
7.1 How To Use The Parts List....................................................................7-1
7.1 Sample Assembly...................................................................................7-1
7.2 Anti-Kickback Assembly & Press Roller...............................................7-2
7.3 Blades Drive Shaft Assembly.................................................................7-4
7.4 Spacer Mounting Kit (Optional).............................................................7-6
7.5 Covers.....................................................................................................7-7
7.6 Infeed Roller Assemblies & Roller Chains............................................7-9
7.7 Board Guide Fence...............................................................................7-10
7.8 Motor Assembly, Control Box, Electric Box, Safety Switches ...........7-11
7.9 Blade Setting Assembly .......................................................................7-13
7.10 Laser Guide Assembly (Optional)........................................................7-15
7.11 Control Box..........................................................................................7-17
7.12 Table.....................................................................................................7-18
7.13 Sawdust Hopper....................................................................................7-20
7.14 Edger Decals.........................................................................................7-21
SECTION 8 DC ELECTROMAGNETIC BRAKE 8-1
8.1 Design and Principle of Operation.........................................................8-1
8.2 Service....................................................................................................8-2
Servicing The Edger
If You Need To Order Parts
1
1
-
1
EGdoc082610
Servicing The Edger
SECTION 1 SERVICING THE EDGER
Wood-Mizer is committed to providing you with the latest technology, best quality and strongest
customer service available on the market today. We continually evaluate our customers’ needs to
ensure we’re meeting current wood-processing demands. Your comments and suggestions are
welcome.
1.1 If You Need To Order Parts
From Europe call our European Headquarters and Manufacturing Facility in Kolo, ul. Nagórna 114,
Poland at +48-63-2626000. Please have the machine identification number and your customer
number ready when you call. Wood-Mizer will accept these methods of payment:
Visa, Mastercard, or Discover
COD
Prepayment
Net 15 (with approved credit)
Be aware that shipping and handling charges may apply. Handling charges are based on size and
quantity of order. In most cases, items will ship on the day they are ordered. Second Day and Next
Day shipping are available at additional cost.
1.2 Customer and Edger Identification
Each Wood-Mizer edger has a serial number. In addition, when you pick up your edger, you will
receive a customer number. These three numbers will help expedite our service to you. Please
locate them now and write them below so you have quick, easy access to them.
See Figure 1-1. See the following figures for serial number locations.
FIG. 1-1
Serial Number
Servicing The Edger
If You Need Service
Servicing The Edger
EGdoc082610
1
-
2
1
1.3 If You Need Service
From Europe call our European Headquarters and Manufacturing Facility in Kolo, Nagórna 114,
Poland at +48-63-2626000. Ask to speak with a Customer Service Representative, please have your
machine identification number and your customer number ready when you call. The Service
Representative can help you with questions about the operation and maintenance of your edger.
He also can schedule you for a service call.
Office Hours:
1.4 Edger Components
See Figure 1-2. The major components of the Edger are shown below.
Country Monday - Friday Saturday Sunday
Poland 7-16 Closed Closed
FIG. 1-2
Tb0038
Outfeed Table
Control Panel
Infeed Table
Sawdust Hopper
Motor
Electric Box
Blade Position Motor
SAFETY
Safety Symbols
2
2-1 EGdoc082610 Safety
SECTION 2 SAFETY
2.1 Safety Symbols
The following symbols and signal words call your attention to instructions concerning your personal
safety. Be sure to observe and follow these instructions.
DANGER! indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING! suggests a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION! refers to potentially hazardous situations which, if not
avoided, may result in minor or moderate injury or damage to
equipment.
IMPORTANT! indicates vital information.
NOTE: gives helpful information.
Warning stripes are placed on areas where a single decal would be
insufficient. To avoid serious injury, keep out of the path of any
equipment marked with warning stripes.
2.2 Safety Instructions
NOTE: ONLY safety instructions regarding personal injury are listed in this section.
Caution statements regarding only equipment damage appear where applicable throughout the
manual.
Observe Safety Instructions
IMPORTANT! Read the entire Operator's Manual before operating the
Edger. Take notice of all safety warnings throughout this manual and
those posted on the machine. Keep this manual with this machine at all
times, regardless of ownership.
Also read any additional manufacturer’s manuals and observe any
applicable safety instructions including dangers, warnings, and
cautions.
!
!
SAFETY
Wear Safety Clothing
Safety EGdoc082610 2-2
2
Only persons who have read and understood the entire operator's
manual should operate the Egder. The Egder is not intended for use by
or around children.
IMPORTANT! It is always the owner's responsibility to comply with all
applicable federal, state and local laws, rules and regulations regarding
the ownership and operation of your Wood-Mizer Edger.
All Wood-Mizer owners are encouraged to become thoroughly familiar
with these applicable laws and comply with them fully while using the
Egder.
Wear Safety Clothing
WARNING! Secure all loose clothing and jewelry before operating the
machine. Failure to do so may result in serious injury or death.
WARNING! Always wear gloves and eye protection when handling
bandsaw blades. Changing blades is safest when done by one person!
Keep all other persons away from area when coiling, carrying or
changing a blade. Failure to do so may result in serious injury.
WARNING! Always wear eye, ear, respiration, and foot protection
when operating or servicing the Egder.
SAFETY
Keep Egder And Area Around Clean
2
2-3 EGdoc082610 Safety
Keep Egder And Area Around Clean
DANGER! Maintain a clean and clear path for all necessary movement
around the Egder and lumber stacking areas. Failure to do so will
result in serious injury.
Dispose Of Sawing By-Products Properly
IMPORTANT! Always properly dispose of all sawing by-products,
including sawdust and other debris.
Check Edger Before Operation
DANGER! Make sure all guards and covers are in place and secured
before operating the Egder. Failure to do so may result in serious
injury.
WARNING! Always shut off the motor to stop the blade whenever the
Edger is not in use. Failure to do so may result in serious injury.
WARNING! Do not for any reason adjust the motor drive belts with the
motor running. Doing so may result in serious injury.
WARNING! Always ensure that there is a sharp point on the
anti-kickback fingers before each use of the Edger.
Be sure anti-kickback fingers are free from obstruction and are in a
downward position with lever released. Failure to do so may result in
serious injury.
Keep Persons Away
DANGER! Keep all persons out of the path of moving equipment and
boards when operating the Edger. Failure to do so will result in serious
injury.
!
Otros manuales para Edger Multirip
1
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Torno de woodmizer
