Woodley Clinispin MPC Manual de usuario
Operator’s Manual
CLINISPIN MPC Multi Purpose Centrifuge
Rev. 1.0
Table of Contents
Model Description
Supplied Accessories
Warranty Information
Specifications
Control Panel / Parts of the Centrifuge
Safety Precautions
Setup Location
Initial Setup Procedure
Operation
Rotor Configuration
Filling of Capillary Tubes
Rotor Installation
Control Panel Functions
Advanced User Settings
Care and Maintenance
Troubleshooting
page 2
Page 3
Page 3
Page 4
Page 4
Page 5
Page 6
Page 7
Page 7
Page 8
Page 10
Page 11
Page 12
Page 13
Page 17
Page 16
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - -
- - - - - - - - - - - - - - - -- - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - -- - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Page 15
Control Panel Functions Page 14
- - - - - - - - - - - - - - - - - - - - - - - - -
page 3
WARNING:
For the safety of both the operator and service personnel,
care should be taken when handling substances that are known to be toxic,
radioactive or contaminated with pathogenic micro-organisms when using this
centrifuge. When Risk Group II materials are used (as identified in the World
Health Organization “Laboratory Bio-Safety Manual”), a Bio-Seal should be
employed. The rotor and rotor accessories should not be considered as Bio-
Seals. More than one level of protection must be provided in the case of
materials of a higher group. The use of flammable or explosive materials as well
as those materials which chemically react vigorously is prohibited.
MODEL DESCRIPTION
The Clinispin Multi Purpose Centrifuge (MPC) is a high speed centrifuge
equipped with a maintenance free drive, digital display and simple interface for
silent & efficient operation. It is designed to provide
rapid and accurate Haematocrit determination
using capillary tubes. It is used for the
determination of volume fractions of
red cells in blood and also for separation
of blood.
The horizontal rotor allows for quick and easy sample loading.
3 pre-defined pre-sets allows easy and rapid operation at one press of a button.
SUPPLIED ACCESSORIES (Standard)
Also included (not shown):
• User Manual • Power Adaptor • Power Cord • T - Allen Key
Note: The rotor and rotor accessories are rated for a rotational speed of 12000 RPM (14119 x g)
One (1)
12 Slot Micro Tube Rotor
Twelve (12)
0.5/0.4ml tubes holder
Twelve (12)
0.3/0.2ml tubes holder
One (1)
24 Tube HCT/QBC Rotor
page 4
SPECIFICATION:
Motor : Brushless DC Motor
Maximum Speed : 12000 RPM
Maximum RCF : 14119 x g (HCT Rotor)
9982 x g (12 slot tube rotor)
Speed accuracy : ± 100 RPM
Maximum Time : 99 minutes
Acceleration time : 65 ± 5 seconds
Braking time : 65 ± 5 seconds
Weight : 6 Kg
Overall Dimensions : 361 x 291 x 120 mm (L x W x H)
Maximum Volume : 24 x 75 mm (HCT)
12 x 2 ml (Serum/ Plasma)
Permitted Environment Conditions
Ambient Temperature during operation : 4°C to 40°C
Maximum Relative Air Humidity : <80%
Noise Level : <60 dB
Electrical Requirements
Input Voltage : 110 - 240 VDC, 50 / 60 Hz
Output Voltage : 24VDC, 6.25 A
Power Consumption : 134.5 W
WARRANTY:
Woodley Equipment Company warranties that this centrifuge is free from
defects in workmanship and parts for 12 months.
Old Station Park Buildings
St. John’s Street, Horwich
Bolton BL6 7NY, United Kingdom
Tel: +44 (0) 1204 669033 • Fax: +44 (0) 1204 669034
www.woodleyequipment.com Email: sales@woodleyequipment.com
www.horizoncentrifuges.com Email: [email protected]
page 5
CONTROL PANEL / PARTS OF THE CENTRIFUGE
Lid lock bracket
Lid
Tachometer
window
HCT rotor
Rotor nut
Control panel
Speed Setting
Button
Speed Button
RPM indicator LED
Increment button
Serum/Plasma
indicator LED
Serum/Plasma
button
(preset)
HCT/QBC
button
(preset)
Urine button
(preset)
HCT/QBC
indicator LED
Speed
display
Time
Display
RCF
indicator LED Time Setting
button
Stop/Open
button
Decrement button
Urine indicator LED
Power Button
Power Port
Air intake
USB Port
Tachometer
window
SAFETY PRECAUTIONS
• Never use the centrifuge in any manner not specified in this manual.
• Equipment used in any manner not specified in this manual or by the
manufacturer, the protection provided by the equipment may be impaired.
• Never move the centrifuge while the rotor is spinning.
• The rotor and the rotor lid must always be securely fastened. If the centrifuge
makes unusual noise during operation, the rotor or rotor lid fitment needs to be
checked. Switch off the device immediately by pressing STOP, check rotor lid &
fasten securely.
• The rotors must be loaded symmetrically. Each tube should be counter balanced
by another tube of same weight and volume.
• Do not use centrifuge or rotor that have not been correctly installed or damaged.
• Repairs must only be performed by authorised service technician.
• Only use recommended original rotors and spare parts.
• Centrifuge may be used for the specified applications only. It must not be
operated in a hazardous or flammable environment and must not be used to
centrifuge explosive or highly reactive substances. Also do not place the
potential hazardous material within the clearance area/envelope.
• If liquids are spilled on the rotor or rotor chamber, the centrifuge must be cleaned
carefully and properly before being used again.
• Prior to centrifugation, the tubes should be visually inspected for material
damage. Damaged tubes may not be centrifuged. This is because broken tubes
can, in addition to sample loss, create imbalance which can result in further
damage to the centrifuge and accessories.
• Rotors and rotor lids are high-graded components which are subject to extreme
mechanical strain. Even slight scratches and tears can lead to serious internal
material damage. Ensure to check rotor for any signs of damage before use.
• Rotor & rotor lid showing visible signs of corrosion or mechanical damage should
not be used.
page 6
page 7
SETUP LOCATION
1) The MPC is supplied in a box. Open the box, then remove the packaging and
gently take the centrifuge out of the small box. Before 1st time usage, open the
centrifuge & ensure to remove all packaging from the rotor chamber & ensure
rotor is firmly tightened. The user manual and accessories should be kept with
the centrifuge.
2) Choose a setup location which meets the following criteria:
a) A bench top clearance height of 40 cms is required in order to open the lid.
b) The clearance envelope is the space around the centrifuge which is
required for safety. Choose a setup location which will allow for a clearance
envelope of at least 60 x 60 cms, (with centrifuge at the centre). No person
or hazardous material shall be permitted in the clearance envelope during
operation. The operator time within the envelope shall be limited to the time
necessary for loading, uploading and centrifuge operation only.
c) Proper ventilation is necessary to prevent the overheating of samples as
well as premature failure of the centrifuge. Choose an area which will allow
unencumbered air flow.
d) The centrifuge is designed to rest on its four rubber feet. No adjustment is
necessary for leveling the centrifuge, however, the surface should be flat
and leveled.
e) Be sure the outlet is always within reach as the main lead is the means of
emergency disconnection.
INITIAL SETUP PROCEDURE
1. Connect one side of power adaptor to rear
side of centrifuge and other to approved
electrical outlet.
2. Rotate clockwise the adaptor nut to tighten the
adaptor with the centrifuge. Ensure the power
switch is OFF while connecting the power adaptor.
page 8
3. For operator safety, the locking system is always active requiring power and
direction from the user to disengage it (the lid also automatically unlocks at the
end of a run when it is safe to do so). To unlock the lid (in order to access the rotor
chamber) press the ‘OPEN / STOP’ button on the control panel.
4. Open the lid and spin the rotor by hand and check for free and level rotation. If the
rotor does not spin freely, refer to the section on troubleshooting (page 17).
5. Ensure that the rotor lid is tightened securely.
6. Close the lid by pressing down firmly. The centrifuge will not run unless the lid is
latched properly.
7. Initiate a test run by pressing the ‘START’ button.
8. The centrifuge starts and reaches the set RPM steadily. When the set RPM /
RCF is reached the timer starts to countdown.
9. Listen to the sound of the centrifuge. A smooth whirring sound should be heard. If
there are any loud or unusual sounds, stop the centrifuge by pressing the ’OPEN /
STOP’ button immediately and refer to the section on troubleshooting (page 17).
10. Press the ‘OPEN / STOP’ button to terminate the test run. The rotor will decelerate
to a complete stop and the lid will then unlock automatically when rotor comes to
standstill.
11. The centrifuge is now ready for operation.
OPERATION
NOTE: Follow the initial setup procedure before initial operation.
1. Press the ‘OPEN / STOP’ button to unlock the lid and then open the lid.
2. Open the transparent rotor lid by loosening the rotor lid nut and place the
capillary tubes with samples into the rotor tube carriers. Be sure to follow the
rules for balanced loads.
3. Ensure that the rotor lid is tightened securely.
4. Close the centrifuge lid by pressing firmly. If the lid is not completely latched,
the error “LID OPEN’ will appear in the display and the centrifuge will not
operate. To resolve the error, see the troubleshooting guide. (Page 17)
page 9
5. Set the desired speed and run time by using the appropriate preset button
and if further adjustment is necessary use the appropriate increment and
decrement buttons.
6. Begin the run by pressing the ‘START’ button on the control panel.
7. The centrifuge should begin to spin. A smooth whirring sound should be
heard.
IF A PROBLEM IS FOUND DURING A SPIN THAT REQUIRES THE CENTRIFUGE
TO BE SHUT DOWN, PRESS THE ‘OPEN / STOP’ BUTTON IMMEDIATELY !
8. Once the set speed is reached the timer will begin - the remaining time will be
displayed on screen.
After time has elapsed, the rotor will decelerate to a complete stop.
9. The centrifuge lid will unlock automatically and will allow access to rotor
chamber.
10. Once the lid is unlocked, open the lid by hand to 90 degrees for
accessing the rotor chamber.
11. Open the rotor lid and remove the samples.
Tabla de contenidos
Otros manuales de Equipo de laboratorio de Woodley
Woodley
Woodley Clinispin Horizon 853VES Manual de usuario
Woodley
Woodley Clinispin Micro III Manual de usuario
Woodley
Woodley Clinispin Micro II Manual de usuario
Woodley
Woodley CLINISPIN HORIZON 842VES Manual de usuario
Woodley
Woodley Clinispin HORIZON 12 Flex Manual de usuario
Woodley
Woodley Clinispin Horizon 6 Flex Manual de usuario
Woodley
Woodley Clinispin CT25 Manual de usuario
Woodley
Woodley Clinispin Vet Combi Manual de usuario
Woodley
Woodley Clinispin HCT II Manual de usuario
Woodley
Woodley Clinispin HCT Manual de usuario
Manuales populares de Equipo de laboratorio de otras marcas
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manual de usuario
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manual de usuario
NI
NI PXI-5422 Manual
Collomix
Collomix Aqix Manual de usuario
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario
Ocean Insight
Ocean Insight FLAME-NIR+ Manual de usuario
