Woodland Mills WG24 Manual de usuario

OPERATOR’S MANUAL

WG24-MY2019: Rev A

Publication Date: 22-Oct-2018

WG24 PTO STUMP GRINDER

This page intentionally left blank.

WG24 Operator’s Manual



TABLE OF CONTENTS

TABLE OF CONTENTS 1____________________________________________

INTRODUCTION 2__________________________________________________

INTENDED USE 3__________________________________________________

TECHNICAL SPECIFICATIONS 3______________________________________

TOOLS REQUIRED 3_____________________________________________

OVERALL DIMENSIONS 4_________________________________________

3-POINT HITCH DIMENSIONS 5____________________________________

GENERAL SAFETY RULES 6_________________________________________

PERSONAL SAFETY 7______________________________________________

MACHINE USE AND CARE 8_________________________________________

ASSEMBLY 9______________________________________________________

1. DEFLECTOR 9_______________________________________________

2. MANUAL TUBE 10_____________________________________________

SET-UP PROCEDURES 11___________________________________________

TRIMMING THE PTO SHAFT 11_____________________________________

PTO SHAFT CLUTCH RUN-IN 13____________________________________

FLYWHEEL TOOTH TORQUING 15__________________________________

EQUIPMENT OPERATION 16_________________________________________

STUMP GRINDING PROCEDURE 19________________________________

INCORRECT GRINDING PROCEDURES 20___________________________

PULLING THROUGH THE CENTRE 20_____________________________________

GRINDING LEFT-TO-RIGHT 20___________________________________________

CHAINSAW HOLDER 21___________________________________________

STORAGE 21___________________________________________________

MAINTENANCE 22_________________________________________________

REPLACING TEETH 22___________________________________________

PARTS LIST 23____________________________________________________

EXPLODED ASSEMBLY 24__________________________________________

NOTES 25________________________________________________________

WG24-MY2019: Rev A

Page of 128

22-Oct-2018

WG24 Operator’s Manual



INTRODUCTION

Congratulations on your purchase and welcome to Woodland Mills! This manual gives you the

necessary information about your machine so you will be able to use it properly. The entire

manual must be read and understood before you start using the machine. If any questions

should arise that are not covered by this manual, please contact Woodland Mills Inc.

This machine is designed for certain applications only. We strongly recommend that this

machine not be modiﬁed and/or used for any application other than that for which it was

designed. If you have any questions relative to a particular application, DO NOT use the

machine until you have ﬁrst contacted us to determine if it can or should be performed with the

product.

For technical questions and replacement parts, please contact Woodland Mills Inc.

OWNER'S RECORD

Please take a moment to record the following information about your stump

grinder. If you need to call for assistance, please be ready to provide your

model and serial numbers. This information will allow us to help you more

quickly when you call.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

WG24-MY2019: Rev A

Page of 228

22-Oct-2018

WG24 Operator’s Manual



INTENDED USE

This stump grinder is designed for grinding stumps using a tractor’s Power Take-Off (PTO) at an

operating rpm of 540.

TECHNICAL SPECIFICATIONS

TOOLS REQUIRED

* Recommended but not required.

** Only if PTO shaft requires trimming. See Trimming the PTO Shaft section for more detail.

Item

Specification

Recommended Horsepower

20 - 45 hp

Flywheel Diameter

24" (610 mm)

Number of Teeth

Tooth

Grade 8.8 Carbide Steel, Bolt-in

Tooth Torque Speciﬁcation

160 ft•lb (215 N•m)

Required PTO Speed

540 rpm

Maximum Cutting Depth Per Pass

5" (127 mm)

Maximum Depth Below Grade

6" (152 mm)

Shipping Weight

470 lb (213 kg)

Tool

Specification

Use

Phillips Head Screwdriver

No. 3

Assembly

Wrench/Socket

13 mm (2X)

Assembly

Wrench/Socket

16 mm (2X)

PTO Clutch Run-In

Wrench/Socket

17 mm

PTO Clutch Lock Pin

Wrench/Socket

24 mm

Tooth Replacement

Torque Wrench

Capable of 160 ft•lb (215 N•m)

Multiple

Calliper*

Vernier, Dial, or Digital

PTO Clutch Run-In

Hacksaw**

PTO Trimming

Coloured Pencil/Marker

PTO Clutch Run-In

WG24-MY2019: Rev A

Page of 328

22-Oct-2018

WG24 Operator’s Manual



OVERALL DIMENSIONS

WG24-MY2019: Rev A

Page of 428

22-Oct-2018

27-5/16"

694mm

42-1/4"

1073mm

31-7/8"

809mm

WG24 Operator’s Manual



3-POINT HITCH DIMENSIONS

WG24-MY2019: Rev A

Page of 528

22-Oct-2018

13-1/8"

334mm

18-1/4"

464mm

16"

407mm

14-7/8"

378mm

12-1/2"

318mm

2-1/4"

57mm

25-3/4"

654mm

31-1/4"

794mm

12-1/16"

307mm

WG24 Operator’s Manual



GENERAL SAFETY RULES

•All Federal and State laws and any regulation having jurisdiction covering the safety

requirements for use of the machine take precedence over the statements in this manual.

Users of this machine must adhere to such regulations.

•Only people that have read and understood these instructions are permitted to use the stump

grinder.

•Inspect the stump grinder and tractor at the beginning of every working day and repair any

defects.

•Stop the engine and make sure that the machine will not start accidentally while repairing

defects or performing maintenance.

•Do not disable or remove the stump grinder’s safety devices.

•Always locate and mark buried wires, cables, and pipelines prior to grinding.

WG24-MY2019: Rev A

Page of 628

22-Oct-2018

The warnings, cautions, and instructions discussed in this instruction

manual cannot cover all possible conditions or situations that could

occur. It must be understood by the operator that common sense and

caution are factors which cannot be built into this product but must be

supplied by the operator.

WARNING!

Read and understand all instructions. Failure to follow all instructions

listed below may result in electric shock, ﬁre, and/or serious injury.

WARNING!

WG24 Operator’s Manual



PERSONAL SAFETY

•Stay alert, watch what you are doing and use common sense when operating machinery. Do

not use a machine when you are tired or under the inﬂuence of drugs, alcohol, or medication.

A moment of inattention while operating machinery may result in serious personal injury.

•Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair,

clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and should be avoided.

•Use safety apparel and equipment. Use safety goggles or safety glasses with side shields

which comply with current national standards, or when needed, a face shield. Use a dust

mask in dusty work conditions. This applies to all persons in the work area. Also use non-

skid safety shoes, hardhat, gloves, dust collection systems, and hearing protection when

appropriate.

•Do not overreach. Keep proper footing and balance at all times.

•Remove adjusting keys or wrenches before connecting to the power supply or turning on

the machine. A wrench or key that is left attached to a rotating part of the machine may result

in personal injury.

•Never conduct any maintenance or make any other adjustments while the tractor

engine is running. Always shut the tractor engine off, remove the ignition key, and keep the

engine off before carrying out any of the following procedures. Consult your tractor’s operator

manual for safe shutdown procedures to prevent accidental ignition.

•Never allow passengers to ride on the stump grinder.

WG24-MY2019: Rev A

Page of 728

22-Oct-2018

WG24 Operator’s Manual



MACHINE USE AND CARE

•Always be sure the operator is familiar with proper safety precautions and operation

techniques before using machine.

•Do not force the machine. Machines do a better and safer job when used in the manner for

which they are designed.

•Storing the machine. When the machine is not in use, store it in a dry, secure place or keep

it well-covered and out of the reach of children. Inspect the machine for good working

condition prior to storage and before each use.

•Maintain the machine. It is recommended that the general condition of the machine be

examined before it is used. Keep your machine in good working order by adopting a program

of conscientious repair and maintenance in accordance with the recommended procedures

found in this manual. If any abnormal vibrations or noise occurs, turn the machine off

immediately and have the problem corrected before further use.

•Cleaning. Use a pressure washer to clean the carbide teeth while taking care not to

pressure-wash the bearings as this could introduce water into areas of the machine that may

cause malfunction or damage.

•Use only accessories that are recommended by the manufacturer. Accessories that may

be suitable for another machine may create a risk of injury when used on this machine.

•Always operate the machine with all safety devices and guards in place and in good working

order. DO NOT modify or make changes to safety devices. DO NOT operate the machine if

any safety devices or guards are missing or inoperative.

•Never leave the machine running unattended.

•Never use the machine to grind anything other than stumps or for any purpose other

than grinding stumps as described in this manual.

WG24-MY2019: Rev A

Page of 828

22-Oct-2018

Otros manuales para WG24

Tabla de contenidos

Otros manuales de Amoladora de Woodland Mills

Woodland Mills

Woodland Mills WG24 Manual de usuario

Manuales populares de Amoladora de otras marcas

Parkside

Parkside PWS 230 C3 Manual de usuario

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Manual técnico

PTA

PTA P1322 Manual de usuario

Crown

Crown CT13313 Manual de usuario

Parkside

Parkside 280250 Manual de usuario

Climax

Climax VM2150 Series Manual de usuario

Jet

Jet JPSG-618M1 Manual de servicio

Makita

Makita GA4030 Manual de usuario

DeWalt

DeWalt DWEN202 Manual de usuario

Grizzly

Grizzly G2790 Manual de usuario

Fein

Fein MSf843-1a Manual de usuario

Bosch

Bosch GWS 14,4 V PROFESSIONAL Manual de usuario

RAMSET

RAMSET CBAGR18 Manual de usuario

Bosch

Bosch 8-115 Z Manual de usuario

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Manual de usuario

MW TOOLS

MW TOOLS ME15W Manual de usuario

Caravaggi

Caravaggi SP 20 Instrucciones de funcionamiento

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Manual técnico