WolfVision VZ-C12 Manual de usuario
INSTALLATION MANUAL
MONTAGEANLEITUNG
INSTALLATION MANUAL
MONTAGEANLEITUNG
Check out our Internet Homepage for additional information
www.wolfvision.com/support
ENGLISH / DEUTSCH
³ ³
VZ-C12 / VZ-C32
R
³ ³
VZ-C12 / VZ-C32
Precautions ENGLISH
Please observe the following:
Risk of electric shock
Dangerous voltage inside
WARNING!
CAUTION! INSTALLATION AND SERVICING OF THE VISUALIZER MUST BE PERFORMED BY
QUALIFIED SERVICE/INSTALLATION PERSONNEL FOLLOWING THE MANUFACTURER'S
INSTALLATION INSTRUCTIONS AND IN COMPLIANCE WITH THE NATIONAL ELECTRIC CODE,
ALL LOCAL BUILDING AND SAFETY CODES AND ALL OTHER APPLICABLE CODE PROVISIONS
OR REGULATIONS.
P I N C H P O I N T ! M O V I N G F O L D I N G M E C H A N I S M C A N C R U S H F I N G E R S .
KEEP HANDS CLEAR. LOCKOUT BEFORE SERVICING.
USE THIS UNIT ONLY WITH THE CORRECT VOLTAGE AS SHOWN ON THE TYPE LABEL !
DO NOT EXPOSE THE UNIT TO HEAT OR MOISTURE !
PROTECT THE UNIT FROM EXCESSIVE SHOCKS !
Make sure that sufficient air circulation for cooling the unit is possible (around the unit)!
If there is any abnormality (abnormal noise, smell, smoke etc.) disconnect the unit from mains
immediately and contact your Visualizer dealer!
Do not use a damaged power cord. This may cause short circuits or electrical shocks!
To prevent danger, do not modify the unit or operate without the cover panel firmly in place!
Do not expose the unit to water, metallic objects or any flammable material.
Avoid installing the unit in locations exposed to strong magnetic fields or electrical currents.
Avoid installing the unit in environments where there is radiation. This could cause monitor image
distortion or damage to the CCD camera.
Do not pull the plug from the power socket with wet hands!
If the unit is not used for a long time, disconnect it from mains!
Precautions for laser pointer:
Laser light - Do not stare into beam!
Do not modify the laser!
Do not view the laser beam with optical instruments!
1
Information for laser pointer
FDA accession number: 9912688-00
This device complies with 21 CFR 1040.10 and 1040.11
The laser beam exits the
remote control through the
smaller (left) opening on
the front.
Technical data:
λ= 635 - 680nm
P< 1mW
Θ2mrad
This label will be found on the
underneath of the remote
control.
security lock
mechanism
CAUTION!
Pinch Point!
EU 0 362 737 KR 128059 AU 765617
DE P58907684.1-08 US 5,027,219 CN ZL99118847.0
CN 89107780.4 EU 0 987 874 and others
JP 1725033 JP 3 544 900
FCC information:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules.
Information to user:
The user manual or instruction manual for an intentional or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This product is built according to Directive EMC and to Directive electrical equipment.
Inspections, tests and evaluation are according to UL 60950. CSA 22.22-60950
Inspections, tests and evaluation are according to the CB-Scheme
Inspections, tests and evaluation are according to the PCT-Scheme
Marks on the unit:
Approval
Worldwide Patents
Copyright Information
Copyright © by WolfVision. All rights reserved.
WolfVision, Wofu Vision and are registered trademarks of WolfVision Holding AG, Austria.
No part of this document may be copied, reproduced, or transmitted by any means, without prior written
permission from WolfVision. Except documentation kept by the purchaser for backup purposes.
In the interest of continuing product improvement, WolfVision reserves the right to change product
specifications without notice.
Information in this document may change without notice.
Disclaimer: WolfVision shall not be liable for technical or editorial errors or omissions.
The units are "MADE IN EU/AUSTRIA”
Printed in Austria, March 2014
Tested to complywith
FCC standards for
home or office use
2
This symbol marks safety instruction procedures where a High Risk of Personal Injury is
present. Be sure to read all directions very carefully and exercise extreme caution! Also be sure
to follow proper health and safety rules in accordance with applicable local and federal laws.
This symbol marks instructions that require special attention in order to avoid possible
Equipment Damage.
The Ceiling Visualizer is built with state-of-the-art technology and is safety engineered. Regardless of this,
operational risks may be present if proper safety procedures are not obeyed.
It is essential that all safety and instruction procedures are read and followed accordingly!
- Store all operation manuals in an easily accessible area !
- The unit must be installed or repaired by authorized and certified personnel only !
- Always follow safety and operational procedures when working with the unit !
- Respect all warning and operation signs !
- Security features must not be disabled or removed !
1.) Inspect the unit for any transport damage. In the event that damage is found, call your
WolfVision dealer immediately and do not attempt installation of the Ceiling Visualizer !
2.) Confirm that all parts and are present.accessories
Read through the entire Installation Manual before beginning with the installation !
Due to the diverse installation possibilities of our ceiling mounting bracket, WolfVision kindly requires you to
mount the appliance only on a concrete ceiling capable of carrying heavy load. Please study the following
installation steps carefully. Should you encounter any problems (not covered in the installation
instructions), please contact your WolfVision representative for assistance. Take special notice regarding
the weight of the Ceiling Visualizer and the potential for personal injury, as well as the possibility for damage
to the Ceiling Visualizer or other objects that may occur if proper mounting precautions are not followed !
Failure to follow instructions can lead to severe injury!
To avoid possible injury, ensure that the ceiling construction is able to support five times
the required Visualizer weight !
Attention
Attention
Warning
G
G
Symbol Legend
Safety Procedures
Preparation
Ceiling Preparation
3
A difference between Ceiling- and "Desktop-"Visualizers is that the size of the smallest and largest image
the unit can pick up is not fixed. This depends on how high above the working surface the Visualizer is
mounted. It is very important to know which image sizes you would like to pick up with the Ceiling
Visualizer before installing the unit, in order to correctly calculate the respective mounting height.
Please refer to the calculation program on WolfVision's homepage (see page 5).
The following table shows the distance which is
called "x" in the illustration on the right side:
18°
Distance (refer to tables opposite)
206 mm
8.11 inch
452 mm / 17.8 inch x suspended ceiling
(if required)
ceiling
Speaker
x mm = distance * tan 18° - 291mm
x" = distance * tan 18° - 11.45"
(tan 18° = 0.3249)
In extremely high rooms the smallest image the
unit can pick-up may not be small enough. In
such cases a standard ceiling mount or
projector-lift can be used to suspend the Ceiling
Visualizer further from the ceiling.
INSTALLATION POSITION
Distance to image center
87,5 mm / 344"
y
IMPORTANT:
The center of the image is offset 87.5 mm (3.5 ") to the
right, from the middle of the Visualizer housing !
in mm in mm in Inchin Inch
1,100 66 44 2.84
1,200 99 50 4.79
1,400 164 60 8.04
1,600 229 70 11.28
1,800 294 80 14.53
2,000 359 90 17.78
2,200 424 100 21.03
2,400 489 110 24.28
2,600 554 120 27.53
2,800 619 130 30.78
3,000 684 140 34.03
3,200 749 150 37.28
3,400 814 160 40.53
3,600 879 170 43.78
3,800 944 180 47.03
4,000 1,009 190 50.27
4,200 1,074 200 53.52
4,400 1,139
4,600 1,204
4,800 1,269
5,000 1,334
Distance
Visualizer to
working
surface
Distance
Visualizer-
front to
image center
Distance
Visualizer-
front to
image center
Distance
Visualizer to
working
surface
Audience
4
The following chart shows image size (optical zoom range) in relation to the mounting height:
Picture Size Chart (Regular Distance From m / 44" to 196")1.1m to 5
www.wolfvision.com/wolf/indexdistance.html
A very comfortable method to calculate the exact positioning and the possible image sizes is a dedicated
calculation program on WolfVision's homepage:
Calculation program on WolfVision Homepage
0.00m
0.10m
0.20m
0.30m
0.40m
0.50m
0.60m
0.70m
0.80m
0.90m
1.00m
1.10m
1.20m
1.30m
1.40m
1.50m
1.60m
1.70m
1.80m
2.00m
2.10m
2.20m
43.31" /
47.24" /
55.12" /
62.99" /
70.87" /
78.74" /
86.61" /
94.49" /
102.36" /
110.24" /
118.11" /
125.98" /
133.86" /
141.73" /
149.61" /
157.48" /
165.35" /
173.23" /
181.10" /
188.98" /
197.85" /
0.00" /
3.94" /
7.87" /
11.81" /
15.75" /
19.69" /
23.62" /
27.56" /
31.50" /
35.43" /
39.37" /
43.31" /
47.24" /
51.18" /
55.12" /
59.06" /
62.99" /
66.93" /
70.87" /
78.74" /
82.68" /
86.61" /
Object distance
Horizontal image size *
1.1m
1.2m
1.4m
1.6m
1.8m
2.0m
2.2m
2.4m
2.6m
2.8m
3.0m
3.2m
3.4m
3.6m
3.8m
4.0m
4.2m
4.4m
4.6m
4.8m
5.0m
Wide
Tele Zoom range
* vertical image size
depends on format
horizontal size
4x 3
horizontal size
16 x 9
horizontal size
16 x 10
16:9
16:10
4:3
5
Technical Specifications are Subject to Change!
58,1
Inch
mm
12 0.47
18 0.71
40 1.57
58,1 2.29
60 2.36
70 2.76
72 2.83
80 3.15
90 3.54
92 3.62
95 3.74
125,5 4.94
135 5.31
144 5.67
160 6.3
206 8.11
240 9.45
285 11.22
352 13.86
390 15.35
400 15.75
452 17.8
528 20.79
135
160
80
160
80
40
70
60
72
125,5
206
528
70°
240
144
160
R390
R90
DIMENSIONS OF THE CEILING MOUNT ASSEMBLY (for inch see list)
DIMENSIONS OF THE CEILING VISUALIZER (for inch see list)
IMPORTANT
Sufficient ventilation is to be provided, otherwise it can result to damage of the
equipment.
G
Installation in suspended ceilings:
For normal operation, only a hole in the ceiling panel for camera and light is required. Everything else may
be covered. The unit only needs to be accessed in the event it may require service.
29
Speaker
Audience
352
12
18 95
452
400
285
6
Mounting the Visualizer on the ceiling using WolfVision's ceiling mount can be done very quickly and easily.
IMPORTANT!
The ceiling mount must be affixed directly with three steel anchors as illustrated in fig.1 to concrete to
ensure a secure mounting and operation of the Visualizer! Ensure that the ceiling construction is able to
carry a weight of 80 kg (176 pounds) and that possible collision accidents are prevented.
fig.1
Direction
of the user
Final position of
Visualizer with
ceiling mount
Direction
of the user
concrete
min. 61
Ø 8
Inch
mm
8 0.315
15 0.59
17 0.67
61 2.4
min. 15
max. 17
IMPORTANT: Please give special attention to the country specific regulations for
training and conferencing rooms.
G
G IMPORTANT: Ensure solid mounting and secure connection of all parts to avoid the
possibility that the unit detaches itself from the ceiling.
INSTALLATION OF WOLFVISION’S CEILING MOUNT
7
In order to fix the assembly to the ceiling, please hold the Ceiling
Visualizer to the ceiling mount (fig.2), connect it and turn the unit
by 90 degrees to the left or right (fig.3). The unit is now installed
only temporarily. The installation is not finished yet!
Now, press the release button on the Visualizer to release the unit
(fig.4) and pull the unit downwards (fig.5).
The folding mechanism will be fixed with the automatic security
lock mechanism to prevent injuries because of unintentional fold
up (fig.5). Pull and turn the lock mechanism counter-clockwise to
release it.
LIMITATION OF WARRANTY!
WOLFVISION MAKES NO EXPRESS OR IMPLIED WARRANTY, STATUTORY OR OTHERWISE,
CONCERNING THE PRODUCT, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTY OF MERCHANTABILITY. IN NO
EVENT SHALL WOLFVISION BE LIABLE TO ANY PERSON FOR ANY CONSEQUENTIAL,
INDIRECT EXEMPLARY, SPECIAL OR PUNITIVE DAMAGES OR DAMAGES FOR LOST
PROFITS. WOLFVISION SHALL IN NO EVENT BECOME LIABLE FOR ANY DAMAGES ARISING
OUT OF OR IN CONNECTION WITH A FAULTY INSTALLATION DUE TO (1) THE USE OF
INAPPROPRIATE MOUNTING PARTS, (2) MOUNTING THE CEILING MOUNT TO A CEILING
WHICH DOES NOT PROVIDED A SUFFICIENTLY SECURE SUPPORT OR (3) ANY OTHER
FAULTY WORKMANSHIP.
8
fig.5fig.4
fig.3
fig.2
security lock
mechanism
CAUTION!
Pinch Point!
Move the Visualizer into the desired position (fig.8). Once the position has been found, release the
Visualizer (fig.9) and tighten the Allen screws to prevent the unit from detaching and moving (fig.10).
fig.9
fig.11 fig.12 fig.13
fig.8
All required cables can now be pulled through the opening of the ceiling mount and connected (fig.11).
Move the Visualizer back into the unreleased position (fig.12). Pull and turn the security lock mechanism
counter-clockwise to release it.
Make sure that the folding mechanism is completely closed. You will hear a "click" sound when it is
completely closed. (fig.13).
security lock
mechanism
Mount the stabilization ring with the enclosed Allen screws loosely into the corresponding screw threads
(fig.6). Don’t tighten the Allen screws yet.
Now move the Ceiling Visualizer into unreleased position (fig.7). Pull and turn the security lock mechanism
counter-clockwise to release it.
fig.7
security lock
mechanism
fig.6
fig.10
9
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Lámpara de cabeza de WolfVision
WolfVision
WolfVision VZ-C32 Manual de usuario
WolfVision
WolfVision VZ-8neo Manual de usuario
WolfVision
WolfVision VZ-C11 Manual de usuario
WolfVision
WolfVision VZ-C3D Manual de usuario
WolfVision
WolfVision VZ-C10 Manual de usuario
WolfVision
WolfVision VZ-C6 Manual de usuario
WolfVision
WolfVision VZ-9.4F Manual de usuario
WolfVision
WolfVision VZ-C3D Manual de usuario
WolfVision
WolfVision VZ-8light 4 Manual de usuario
WolfVision
WolfVision VZ-8light3 Manual de usuario
WolfVision
WolfVision VZ-3s Manual de usuario
WolfVision
WolfVision VZ-3 Manual de usuario
WolfVision
WolfVision EYE Series Manual del operador
WolfVision
WolfVision vz-8plus 4 Manual de usuario
WolfVision
WolfVision VZ-9.4 Manual de usuario
WolfVision
WolfVision VZ-C122 Manual de usuario
WolfVision
WolfVision VZ-C6 Manual de usuario
WolfVision
WolfVision VZ-P18 Manual de usuario
WolfVision
WolfVision Visualizer VZ-5D Manual de usuario
WolfVision
WolfVision Visualizer VZ-7D Manual de usuario
