Wizard SmartScreen Motorized Manual de usuario

SmartScreen Motorized

5 ½” and 7” Housing

Measuring and Installation Instructions

Table of Contents

Measuring 5 ½” & 7” Housing Pages 3 to 7

Before Installing 5 ½” & 7” Housing Pages 8 to 9

Installing 5 ½” & 7” Housing Outside Above Header (OAH) Pages 10 to 15

Installing 5 ½” & 7” Housing Inside Under Header (IUH) Pages 16 to 21

Appendices Pages 22 to 25

Mesh Options

Hard Power reset

Adjust Obstacle Detection Setting

Reset Upper and Lower Limits

Replace the Screen Material

5 ½” & 7” Housing SmartScreen Motorized Measuring

These measuring instructions cover both the 5 ½” and the 7” housing SmartScreen Motorized

Minimum width of the SmartScreen Motorized is 3’ wide (necessary to accommodate the motor within the roll tube)

Maximum width is 30’ wide

(25’ max width with Vinyl)

Maximum height is 23’ tall

(16’ max height with Vinyl)

1. Please read before going to site to measure

2. Bookmark the measuring and installation instructions, or print a copy to take with you on the install –

www.wizardscreens.com/technical

3. Call to schedule a training session on installations before going to site

4. When installing, if you have questions, call us before leaving the site

5. Determine the installation type

a. IUH (Inside Under Header)

i. Housing is mounted inside the opening, under the header

i. The housing can be attached through the top in to the header and/or through the end

caps in to the jamb

ii. Tracks are mounted inside the opening between the jams

i. You will need to order 2” x 2” angle to accommodate installing the tracks on the inside

of the opening

ii. The 2” x 2” angle runs from the bottom of the housing to where the slide bar will stop at

the lowest point, or the full length of the track

iii. The angle is attached to the jam on either side of the opening using a flat head fastener

iv. There should be a fastener attaching the angle to the jamb at the top of the angle below

the housing, 2 fasteners in the middle spaced evenly apart, and a fastener at the bottom

close to the lowest point (minimum)

v. The track will then be attached to the 2” x 2” angle

b. OAH (Outside Above Header) or Standard Face Mount

i. Housing is mounted to a wall above the opening

i. The housing can be attached through the back of the housing in to the header

ii. Tracks are face mounted to the left and the right of the opening

6. Determine what material you will be fastening the unit to

a. Different types of fasteners may be necessary depending what material the unit is being fastened to

b. When fastening to a steel (or other metal) structure please take note of where the welds are that

connect the posts to the header as this will affect where the housing is mounted

7. Determine the dimensions of the unit by using the 3 point measuring system *a laser measuring tool is useful

a. Make sure the opening is square

i. Make note of any variances

i. Some variances can be account for and some cannot

b. For the housing width measure in between the posts (in the jamb) at the top, middle and at the bottom

of the opening

i. For the finished width of an IUH install, deduct 3/8” from the narrowest of those 3

measurements

ii. For the finished width of an OAH install, add 5” to the widest of those 3 measurements

c. For the unit height measure from the ground, or lowest point, to the top underneath the header on the

extreme left side, in the middle and on the extreme right side

i. For the finished height of an IUH install, take the tallest measurement

ii. For the finished height of an OAH install, add the height of the housing (5 ½” or 7”) plus the

height of the slide bar (2 ½”) plus the height of the bottom seal (1 ½”) to the tallest

measurement

iii. There should be a minimum of 5 ½” or 7” of header space (depending on housing size) to mount

the housing to

i. If there is not enough space on the header to accommodate the height of the housing,

the slide bar and the bottom seal there may be some parts (either the bottom seal

and/or the slide bar) and the customer should be made aware of this as those parts may

be visible from the backside of the opening. You can use a tape measure to measure the

header to see how much space there is to accommodate the housing, slide bar and

bottom seal

d. If the left or the right side is longer than the other (for a slope in a patio for example) the 1 ½” brush pile

bottom seal will accommodate a 1 ½” bias. If the slope is greater than 1 ½”, up to a 2” bias can be built

in to the mesh to accommodate a total difference of up to 3 ½” between the extreme left and the

extreme right side of the unit

e. Crowns, moldings, humps in the floor, etc. cannot be accommodated

8. Determine the housing size (5 ½” or 7”) and roll tube size ( 4” or 5”)

a. Units 22’and wider and/or 12’ and taller will use a 7” housing and a 5” roll tube

b. Units up to and narrower than 22’ wide and 12” tall will use a 5 ½” housing and a 4” roll tube

c. If a unit is narrower than 20’ and/or shorter than 12’ a 7” housing can be used if necessary

i. If there are 2 or more screens in the same location and at least 1 of those screens must be in 7”

housing due to its size, any of the screens that would normally be in a 5 ½” housing can be

ordered in a 7” housing for aesthetic purposes

d. Units wider than 250” and all units with clear vinyl screen will require the double idler system rather

than the standard pivot

i. Neither the pivot or the double idler system will affect the dimensions of the unit

9. Determine housing, track and slide bar color (and angle if necessary)

a. White, Black, Beige, Bronze, Ivory aluminum

10. Determine the bottom seal option for slide bar

a. 1 ½” black brush pile or 4” grey rubber bottom seal

11. Determine the screen type

a. Insect, solar and clear vinyl options are available

b. A horizontal seam may be necessary for insect and solar mesh options

i. Due to restrictions of the size of the roll width, multiple pieces of mesh may need to be welded

together, causing a seam

ii. A seam can be located at a specified point anywhere between the top of the slide bar and within

the roll width dimension

i. This is useful for the seam to line up with a railing or other obstacle to minimize the look

up the seam

c. Please see attached appendix for mesh options and roll widths

d. Clear vinyl needs to have a colored border surrounding the clear vinyl on 4 sides

i. The minimum dimensions of the border are 8” on the left and right side, 12” on the bottom

above the slide bar and 12 “ between at the top between the roll tube and the top of the clear

vinyl

ii. Border color options are black, white and beige

e. Clear vinyl comes in 50”x 100” width rolls so several panels may need to be welded together running

horizontally to accommodate a width and a vertical seam will be visible

f. If the clear vinyl height is greater than 100” the remaining height is finished with the border material,

even if it is greater than 12”

i. The extra border material can also be added above the slide bar rather than between the roll

tube and the top of the clear vinyl depending on the home owners request

g. When choosing clear vinyl a drawing showing the dimensions of the clear vinyl and the border will be

sent to you for approval. Manufacturing will not start on the vinyl until your approval of the drawing has

been received

h. Manufacturing clear vinyl requires an extended lead time (approximately 1 to 2 weeks)

12. Determine motor location

a. Look at the opening where the screen will be rolling away from you

b. Motor can be located on either the left or the right of the screen

c. Select a side closest to where the outlet is or will be placed

i. The units come with a 10’power cable and 24’ power cables are available if necessary

d. Motors need 110v and pull 1.6 amps per unit

e. For an IUH install the outlet must be towards the back of the unit as the power cord can only exit the

housing or track through the back of the unit

13. Determine motor size

a. All SmartScreen Motorized come with the Somfy Maestria motor with obstacle detection

b. 5” roll tube will use a Somfy 550 motor

c. 4” roll tube will use a Somfy 525 motor

d. The size of the Somfy motor will affect the speed at which the screen rolls up or down

i. 4” roll tube with a 525 motors will roll faster than a 5” roll tube with a 550 motor

ii. It is possible to match roll tubes and motors on a multi-unit project so that all the screens roll at

the same speed *example, units that will need a 4” roll tube on a project with 5” roll tubes can

be upgraded to 5” roll tubes with 550 motor

14. Determine type and number of remotes necessary

a. Somfy offers a 1, 5 and a 16 channel remote

i. If there is only 1 unit a single channel remote will work

ii. Between 2 and 5 units a 5 channel remote will work and each screen can be programmed on to

a separate channel

iii. Between 6 and 16 units a 16 cannel remote will work and each screen can be programmed on a

separate channel

iv. If there is a spare channel on the multi-channel remotes, all of the screens can be added to that

empty channel to allow movement of all the screens at once

v. There is a 30’ max radius for remote usage

i. If there are screens in different areas of the home multiple remotes may be necessary

15. Determine accessories

a. Somfy myLink

i. Converts the homes Wi-Fi to RTS that the motors can read

ii. Allows for control of the screen through an app on a smartphone

iii. Allows for third party home automation integration

iv. The myLink must be located within the Wi-Fi hot zone and within 30’ of the motorized screen

b. Somfy Repeater

i. Increases the distance a remote signal can reach by another 30’

c. Somfy Sun Control

i. Can be set to control the motorized screens based on how much sun it detects

d. Somfy Wind Control

i. Can be set to control the motorized screens based on how much wind it detects

*Please note for Somfy wind and sun control options –using these accessories can cause the screen to be in

motion without it being checked for debris or damage prior to the screen being in motion, which can lead to new

or further damage. Customer would have to use at own risk

16. Place the order using the information gathered during the measuring process through Wizard’s online ordering

system

a. Please ensure to make a note of any and all special requests

i. Examples:

i. Seam location

ii. Extra remotes

iii. Accessories

iv. Bottom seal option

v. Variances in height between the left and right side

5 ½” & 7” Housing SmartScreen Motorized Installing

These installation instructions cover both the 5 ½” and the 7” housing SmartScreen Motorized

*Motorized screen installations require at least 2 people, more may be necessary for wider screens. Please plan

accordingly

Before installing the SmartScreen Motorized units

1. Tools Required:

3/8" cordlessdrill

¼" hex driver bit

#2 Phillips driver bit

3/8" drill bit (10"-14"long)

3/16" drill bit

1/8" drill bit

3/8" hammer drill

3/8" concrete drill bit (10"-14" long)

Concrete drill bits for 3/16" or ¼" concretescrews

Smallflatand Phillips head screwdrivers

k. 2’ level

25’ tape measure

Scissors

Needle nose pliers

Duct tape

Silicone spray for side tracks

3 prong electrical plug (1 per motor)

r. Caulking gun with desired color caulk

Chop saw with non-ferrous blade

t. Concrete, metal or wood fasteners (minimum 2" long)

u. 1” tek fasteners

*drill and fastener bits may be adjusted depending which types and sizes of fasteners are being used

2. Contents of Shipment *contents may vary depending on type or style ordered

a. Housing front, housing back and end caps (attached to each other)

b. Roll tube, motor, pivot (or double idler system) and screen option

i. Screen option will be wrapped around the tube and placed inside the housing for shipping

ii. Motor and pivot will be in the tube

iii. Power cord will be attached to the motor

c. Slide bar with bottom seal attached

d. Tracks with track covers (x2 of each piece)

e. Remote, usually packaged with the tracks and the slide bar (if ordered)

i. With multiple units the remote will be packaged with the tracks and slide bar in one of the units

f. Probes (x2)

g. 2” x 2” angle (x2 of each piece if ordered)

3. Inspect packaging for damage

a. If packaging is damaged the unit may still be free of damage

b. Take care opening the packages to ensure unit is not damaged while opening

c. Inspect unit and pieces and if there is any damage report to Wizard immediately with pictures

4. Remove the units from packaging

a. Place the packages on a flat surface

b. Careful open up and remove packaging

c. Remove the housing, slide bar and tracks (and 2” x 2” angle if included) from each package

d. Cut the tape that holds the packaging material that is wrapped around the housing

e. Remove the plastic tubing from the housing package

f. Remove hex head screws that attach the housing cover to the housing

i. Save these screws

g. Remove housing cover and place it on a flat surface in a safe place

h. With pliers, remove the c-ring that hold the motor to the end cap

i. It is important you do not lose the c-ring

i. Remove roller, screen, pivot and motor by sliding the tube towards the pivot end, compressing the pivot

until the motor comes free from the crown on the end cap

i. Be careful not to tilt the roller as the motor may easily fall out of the roller assembly

ii. Place the roller and motor on a flat surface in a safe place

iii. Take care not to damage the screen that is wrapped around the tube

j. Reinstall the c-ring around the crown on the end cap

k. Cut the tape that holds the packaging material that is wrapped around the slide bar and tracks/track

covers (and 2” x 2” angle if included)

l. Remove the plastic tubing from the slide bar and tracks/track covers (and 2” x 2” angle if included)

m. Set slide bar, tracks, tracks covers (and 2” x 2” angle if included) aside in a safe place

Installing a OAH (Outside Above Header) Unit

1. Install the housing back

a. Turn the housing so that the back is facing up

b. Drill 3/ 16" mounting holes into the back of the housing. Start at the middle and every 24" toward the

ends. The holes should be about ¾ " below the top of the housing. Drill 3/16" mounting holes at each

end of the housing between the two pop rivets (back of housing back)

c. Measure and mark the middle of the housing at the bottom area of the back of the housing

d. Measure and mark on the header the location where the bottom middle area of housing should be on

the header

e. Line up the 2 marks and fasten housing to the header

f. Level housing and fasten to the header through predrilled holes with 2" fasteners

g. Before tightening fasteners to header, attach the front cover of the hood, ensuring the top and back

hood assembly is not bowed and you are able to satisfactorily attach the front cover. Once this is done,

remove front cover and tighten fasteners

h. If the outlet is inside the room

i. At the motor end drill a 3/8" hole through the back of the housing 1" from top and ¾" from the

end for leading the motor wire out of the housing. If the motor wire does not go through the

wall, drill 3 /8 " motor wire hole through the housing or end cap not more than ¾" from end of

housing or in from outer edges of the end cap.

i. If the outlet is above the housing

i. At the motor end drill a 3/8" hole through the top of the housing 1" from top and ¾" from the

end for leading the motor wire out of the housing

j. If the outlet is to the side of the housing

i. At the motor end drill a 3/8" hole through the end cap 1" from top and ¾" from the end for

leading the motor wire out of the housing

2. Install the roll tube

a. Insert the pivot in to the end cap and compress

b. Move the motor end of the tube to line up with the crown on the end cap

i. Ensure the power cord coming out of the motor is facing down

ii. This is to ensure water does not run in to the motor, otherwise call a drip loop

c. Line the shape on the motor to the corresponding shape of the crown and connect the motor to the

crown

i. You must hear a distinctive clicking sound to ensure the motor is completely in place

d. Loop the power cord around the motor and pull through the opening drilled earlier

i. If the outlet is towards the bottom of the screen the cord can hang straight down

3. Install the roll tube using the double idler system

a. Unroll the screen material from the tube

i. Be careful not to damage the screen

ii. Ensure the screen zipper does not move out of the tube

b. Insert the pivot cap in to the end cap and pin in to the bracket using the provided cotter pin

i. Ensure the holes line up

Otros manuales para SmartScreen Motorized

Otros manuales de Accesorios de Wizard

Wizard

Wizard SmartScreen Motorized Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario