Wisenet SHD-3000F4 Manual de usuario
In-ceiling Housing
Installation Manual
SHD-3000F4
2_ SHD-3000F4
Overview 3
What’s Included 3
Installation Instructions 4
Installation
(indoor type) 4
Installation
(outdoor type) 8
Product Specifications 12
TABLE OF CONTENTS
SHD-3000F4 _3
ENG
OVERVIEW
This In-CEILING HOUSING is a mounting ADAPTOR that is designed to mount the smart
dome camera in built-in style on a double-layer ceiling.
WHAT’S INCLUDED
HOUSING SAFETY BRACKET (
1EA)
SAFETY WIRE (1SET)
WARRANTY
TEMPLATE (1EA)
outdoor type (3EA)
indoor type (2EA)
Lower bracket (exclusively for
indoor dome cameras) (1EA)
In-ceiling Housing
Installation Manual
SHD-3000F4
INSTALLATION MANUAL
4_ SHD-3000F4
INSTALLATION INSTRUCTIONS
1. Select an installation position or place that can endure more than 4 times of the total weight
of the installation structure.
2. At least 250mm or more of spare height is required above the CEILING BOARD.
3. CEILING BOARD’s thickness should be less than 40mm.
4. Be sure to secure the SAFETY WIRE to avoid a product fall.
5. If you want to attach the camera to the ADAPTOR, use the only provided SCREWS.
INSTALLATION
(INDOOR typE)
1. Place the tEMpLAtE on the CEILING BOARD and drill a guided hole.
❶ Remove the round filling (“C”) from the tEMpLAtE.
2 Place TEMPLATE A onto the CEILING BOARD to which you will attach the ceiling
mount ADAPTOR and drill a hole of Ø198mm in diameter.
See the figure below for the hole shape.
More than 250mm
CEILING BOARD Less than 40mm
TEMPLATE
CEILING BOARD
SHD-3000F4 _5
ENG
2. Fix the ANCHOR BOLt onto the concrete CEILING, and secure the SAFEty WIRE to the
ANCHOR BOLt as below:
❶ Tighten the nut (“N1”) on the ANCHOR BOLt.
2 Insert the provided SAFEty BRACKEt into the ANCHOR BOLt.
3 Tighten two nuts (“N2”,”N3”) onto the ANCHOR BOLt.
4 Hook and fix one end of the SAFEty WIRE onto the SAFEty BRACKEt.
5 Hook and fix the other end of SAFEty WIRE onto the HOUSING as shown below.
3. To connect to the camera, insert the external cable through the side hole on the housing
to the inside of the housing as shown in the figure.
M
`Refer to the installation manual of the camera that you want to install, and prepare necessary
cables for camera connection.
The ANCHOR BOLTs and nuts are optional and not included in the product package.
ANCHOR BOLT
Nut (N1)
Safety BRACKET
Nut (N2,N3)
SAFETY WIRE
ANCHOR BOLT
HOUSING
CEILING
CEILING
CEILING
Hole HOUSING
HOUSING
External Cable
6_ SHD-3000F4
4. Push the HOUSING inside the CEILING through the CEILING hole, and tighten the
SCREWs (x2) clockwise to fix the HOUSING on the CEILING.
(The BRACKEt will be positioned from <A> to <B> as shown.)
M
`Ensure that the HOUSING is firmly secured to the CEILING BOARD.
5. Combine the dome camera and the bracket using two screws.
Lower bracket is exclusively for indoor use.
INSTALLATION
(INDOOR typE)
BRACKET
SCREW
Turn clockwise
HOUSING
BRACKET
BRACKET
BRACKET
<A> <B>
SHD-3000F4 _7
ENG
6. Insert the bracket where the camera is mounted into the housing and fix it by turning it in
the LOCK direction.
M
`When the installation is completed, remove both PROTECTIVE TAPE and PRETOECTIVE COVER
from the lens.
7. Attach the COVER to the HOUSING.
CEILING
HOUSING
HOUSING
Cover
8_ SHD-3000F4
INSTALLATION
(OUtDOOR typE)
1. Place the TEMPLATE on the CEILING BOARD and drill a guided hole.
❶ Remove the round filling (“C”) from the TEMPLATE.
2 Place the TEMPLATE A onto the CEILING BOARD to which you will attach the
CEILING mount ADAPTOR and drill a Ø198mm hole.
See the figure below for the hole shape.
2. Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the
ANCHOR BOLT as below:
❶ Tighten the NUT (“N1”) on the ANCHOR BOLT.
2 Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
3 Tighten two NUTs (“N2”,”N3”) onto the ANCHOR BOLT.
4 Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.
5 Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below:
The ANCHOR BOLTs and nuts are optional and not included in the product package.
ANCHOR BOLT
CEILING
Nut (N1)
Safety BRACKET
Nut (N2,N3)
SAFETY WIRE
ANCHOR BOLT
HOUSING
CEILING
CEILING BOARD
TEMPLATE
SHD-3000F4 _9
ENG
3. To connect to the camera, insert the external cable through the side hole on the housing
to the inside of the housing as shown in the figure.
M
`Refer to the installation manual of the camera that you want to install, and prepare necessary
cables for camera connection.
4. Push the HOUSING inside the CEILING through the CEILING hole, and tighten the
SCREWs (x2) clockwise to fix the HOUSING on the CEILING.
(The BRACKET will be positioned from <A> to <B> as shown.)
M
`Ensure that the HOUSING is firmly secured to the CEILING BOARD.
CEILING
HOLE HOUSING
BRACKET
SCREW
Turn clockwise
HOUSING
BRACKET
<B><A>
BRACKET
BRACKET
10_ SHD-3000F4
5. As shown in the figure, pull out the protrusions of the rubber cap in the bottom to make a
small hole and remove the cable through it to connect to the external cable.
M
`If waterproofing in the connected cable jacket is poor, it may cause leaks. Make sure you tape it
tight and thoroughly.
`The butyl rubber tape for waterproofing can extend at least twice as long as the original length.
INSTALLATION
(OUtDOOR typE)
Alarm Cable
Audio
Power
Tabla de contenidos
Otros manuales de Accesorios para cámaras de Wisenet
Wisenet
Wisenet SHB-D-9000H Manual de usuario
Wisenet
Wisenet SHD-3000F1 Manual de usuario
Wisenet
Wisenet SHB-4301HP Manual de usuario
Wisenet
Wisenet SHB-9000H Manual de usuario
Wisenet
Wisenet SHD-3000F5 Manual de usuario
Wisenet
Wisenet SHB-4300HP Manual de usuario
Wisenet
Wisenet SKY Manual de usuario
Wisenet
Wisenet SHD-3000F2 Manual de usuario
