Winmate M101B Series Manual de usuario
Please read these instructions carefully before using this product, and save this manual for future use.
Rugged Tablet PC
M101B-Series
Windows 10 IoT Enterprise
Windows Embedded 8.1 Industry Pro
Windows 7 Professional for Embedded System
OS Installation Guide
Version 1.2
Release date: 13-Jan-2017
M101B Series OS Installation Guide
i
Document Revision History
Version
Date
Note
Author
1.0
11-Jul-2016
Initial release
Karen Liu
1.1
23-May-2016
Add Winmate SDK Support
Karen Liu
1.2
13-Jan-2017
Add how to change touch
keyboard size
Karen Liu
ii
CONTENTS
INTRODUCTION 3
BIOS SETUP 4
BIOS Navigation Keys 4
Changing BIOS Settings (UEFI/LEGACY) to Install OS 6
Default Windows 8/8.1 change to Windows 7 6
Default Windows 7 change to Windows 8.1 9
BIOS and EC Firmware Update Guide 12
Tools needed 12
Where to Download BIOS Update Files 12
Preparing USB Drive with BIOS/EC FW Update Files 13
Update/Flash BIOS and EC in UEFI Shell Mode 16
SETTING UP OS FIRST TIME 22
Windows 10 IoT Enterprise 22
DRIVER INSTALLATION 29
Windows 10 IoT Enterprise 29
Windows Embedded 8.1 Industry Pro 30
Windows 7 Professional for Embedded System 31
UTILITY INSTALLATION 32
List of Winmate AP/ Utilities 32
Hot Tab Driver Installation Guide 33
Adjusting COM Port Settings 36
COM Port Settings 36
Adjusting COM Port Number 37
Setting Up Bluetooth COM Port 39
Changing Touch Keyboard Size 41
WINMATE SDK SUPPORT 43
Winmate Download Center 43
Download SDK from Winmate File Share 43
M101B Series OS Installation Guide
3
INTRODUCTION
This document contains references and instructions on operation system and
utility installation. M101B-seriees Rugged Tablet PC is shipped with pre-
installed OS based on your order. This guide also describes the procedure
how to update BIOS or change BIOS settings to install the OS different from
Winmate shipment.
For Standard installation Windows OS installation, you can use
Winmate’s Recovery CD/ DVD or use Recovery Partition and follow
procedures described in the M101B-Series User Manual.
For alternative way, if customer installs OS from Microsoft CD/ DVD; this
document explains some key important information (especially for
Consumer, Non-Embedded OS).
4
BIOS SETUP
There are two ways to install new OS: either through BIOS settings (UEFI /
LEGACY mode) or to update BIOS version.
IMPORTANT:
Chose only one BIOS Setup method for OS Update: either change
BIOS Settings (UEFI/LEGACY mode) or update BIOS version. The
choice depends on your preferences.
BIOS Navigation Keys
This section describes the procedure to enter BIOS settings and introduces
BIOS navigation keys. To enter the BIOS setup, you need to connect an
external USB keyboard, press Del key when the prompt appears on the
screen during start up. The prompt screen shows only few seconds so need
press Del key quickly.
BIOS Navigation Keys
The following keys are enabled during POST:
Key
Function
Del
Enters the BIOS setup menu.
F7
Display the boot menu. Lists all bootable devices that are
connected to the system. With cursor ↑and cursor ↓and by
pressing <ENTER>, select the device used for the boot.
Pause
Pressing the [Pause] key stops the POST. Press any other key to
resume the POST.
M101B Series OS Installation Guide
5
The following Keys can be used after entering the BIOS Setup.
Key
Function
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
Esc
Exit
+/-
Change Opt.
Enter
Select or execute command
Cursor ↑
Moves to the previous item
Cursor ↓
Goes to the next item
Cursor ←
Moves to the previous item
Cursor →
Goes to the next item
6
Changing BIOS Settings (UEFI/LEGACY) to Install OS
This section describes how to change UEFI/LEGACY mode in BIOS settings
to install OS that is different from Winmate shipping.
Default Windows 8/8.1 change to Windows 7
The instruction below describes how to change Windows 8/8.1 to Windows 7.
1. Enter BIOS Setup utility.
2. Go to “Miscellaneous Configuration” at BIOS setup menu.
M101B Series OS Installation Guide
7
3. Change OS setting to Windows 7.
4. Go to CSM Configuration, change Storage and Video to Legacy only.
8
5. Go to Boot menu and change setting Boot Mode select to LEGACY.
M101B Series OS Installation Guide
9
Default Windows 7 change to Windows 8.1
1. Enter BIOS Setup menu.
2. Go into item “Miscellaneous Configuration” at BIOS setup menu.
3. Change OS setting to Windows 8.X.
Otros manuales para M101B Series
8
Tabla de contenidos
Otros manuales de Tableta de Winmate
Winmate
Winmate M101M8-4E Manual de usuario
Winmate
Winmate M700DM4 Manual de usuario
Winmate
Winmate ID83 Manual de usuario
Winmate
Winmate M116P Series Manual de usuario
Winmate
Winmate M101B Series Manual de usuario
Winmate
Winmate M101BU Series Manual de usuario
Winmate
Winmate M101M8 Series Manual de usuario
Winmate
Winmate Porty G4 Manual de usuario
Winmate
Winmate M700DM4-EX Manual de usuario
Winmate
Winmate W07I98M-RTC1 Manual de usuario
Winmate
Winmate Slim-line Manual de usuario
Winmate
Winmate M101BC Manual de usuario
Winmate
Winmate M101B Series Manual de usuario
Winmate
Winmate M101B Series Manual de usuario
Winmate
Winmate M101M8 Series Manual de usuario
Winmate
Winmate M101RK Series Manual de usuario
Winmate
Winmate W07IB3S-PCM1AC Manual de usuario
Winmate
Winmate M133K Manual de usuario
Winmate
Winmate M900EK Series Manual de usuario
Winmate
Winmate M101PR Manual de usuario
