Winegard ConnecT 2.0 Manual de usuario
2452462 REV8-21
Register your product at winegard.com/myantenna
For technical services:
Extreme 2.0
Installation
and
Operation Manual
Parts Included:
Specifications:
WARNINGS:
(1) Extreme 2.0 outdoor unit
(1) Power Over Ethernet power
inserter (POE) indoor only
(1) L-pipe
(1) Wall mount
(1) Pipe mount
(1) Insert
(1) Hardware bag
• Dimensions: 9.35" diameter, 8" tall
• Wireless standard: 802.11a/b/g/n/ac
• Frequency band: 2.4 GHz/5 GHz
• Amplifiers: 3x3 MIMO
• Antennas: (3) 2.4 GHz/5 GHz
• Wireless security:
WPA-PSK (TKIP)
WPA2-PSK (AES)
WPA-PSK (AES) & WPA2-PSK (AES)
WPA2-PSK (AES) & WPA3 (AES)
• Port: (1) RJ45 10/100/1000
• Power rating: Switching, AC input 100-240V, 1.5A
• POE: Not intended for outdoor installation
• Read this manual carefully and completely before attempting to assemble, install, or operate this product. Winegard
recommends that a professional technician installs this equipment.
• Save these instructions.
• POE MUST BE INSTALLED INDOORS.
• DO NOT MOUNT OVER CHIMNEY OPENING.
• Never install unit upside down. Improper installation will cause product damage.
• Do not paint any portion of the Winegard Extreme 2.0. This could damage the system and will void the warranty.
• When you initially set up the Winegard Extreme 2.0, we recommend you check for software updates the first time you
connect the system to an internet signal. We also recommend you check for updates every couple of months for fixes
and added features.
Items required:
Bolts/screws for wall mount
7/16" wrench
Phillips screwdriver
Ethernet cable(s)
2
Installation - Outdoor/Indoor
Outdoor/Indoor Installation The Extreme 2.0 unit may be installed inside or outside. (Ethernet cable not provided – MAX 85 feet)
-OR-
Extreme 2.0
outdoor unit
POE
L-pipe
Wall mount
Pipe mount
Insert
Home
router
Connect to
POE port
LAN port to
home router
3
Access Point or
Bridge Modes
ONLY
Ethernet cable
L-pipe
THE POE IS INDOOR RATED ONLY.
It is not intended for outside use.
Operation - WiFi Extender Mode
IMPORTANT: Keep your/the Quick Start Guide for your records.
It contains your unique factory default SSID and password. You may also find the SSID and
password on the bottom of unit.
NOTE: Recommended browsers: Microsoft®Edge, Firefox®, Google Chrome™, or Safari ®.
WiFi Extender Mode – Increases range.
1) Turn on the WiFi-enabled device(s) that you want to connect and scan for wireless
networks. It may take a few minutes for the network to appear.
2) The label located on the front of the Quick Start Guide or bottom of the unit has the
unique default SSID and password. Select this WiFi signal from the list of wireless
networks and connect. Once the correct SSID has been selected, enter the listed
password. We recommend you set your device(s) to automatically connect with the
Winegard Extreme 2.0.
3) Once connected, open an internet browser on your device and type 10.11.12.1 into the
address bar and press ENTER. Figure 1.
This will take you to the Admin Login screen (Figure 2).
Login using:
Username: admin Password: admin.
4) INTERNET ACCESS – WIFI will need to be selected. If selected move to next step.
5) Press SCAN FOR WIFI (Figure 3). This should take about one minute. The Winegard
Extreme 2.0 will display available networks by signal strength. Select the desired 2.4GHz
signal. Signal strength below 50% is not a recommended network. Click CONTINUE.
6) Enter the network password, if prompted (Figure 4). Once the Winegard Extreme 2.0
connects to the internet, the Internet Status will show Connected. This could take as
long as two minutes. You are now ready to use the WiFi and will see your paired info
under Internet Status and strength under WiFi Signal.
4
NOTE:The system will reboot and you
may need to reconnect to the internet.
Once connected (takes up to two
minutes), the strength of your connection
will appear under the WiFi signal.
You are now ready to use the WiFi.
Figure 1
Figure 2
Figure 4
Figure 3
WiFi 1
Operation - Access Point Mode
Access Point Mode – Provides faster throughput speeds.
1) Connect second Ethernet cable from the LAN port on your POE to your home router.
2) Turn on the WiFi-enabled device(s) that you want to connect and scan for wireless
networks. It may take a few minutes for the network to appear.
3) The label located on the front of Quick Start Guide or bottom of the unit has the unique
default SSID and password. Select this WiFi signal from the list of wireless networks
and connect. Once the correct SSID has been selected, enter the listed password. We
recommend you set your device(s) to automatically connect with the Winegard Extreme 2.0.
4) Once connected, open an internet browser on your device and type 10.11.12.1 into the
address bar and press ENTER Figure 5).
This will take you to the Admin Login screen (Figure 6).
Login using:
Username: admin Password: admin.
5) INTERNET ACCESS - Select Ethernet and press SELECT (Figure 7). Your unit is
connecting and will take about 2 minutes.
5
NOTE: WiFi signal will stay at No signal until connected,
when using Access Point or Bridge Modes.
You are ready to use WiFi.
Figure 5
Figure 6
Figure 7
Operation - Bridge Mode 6
Bridge Mode* – Allows passthrough of your home router connections.
In this mode devices connected to the Extreme’s SSIDs/network will get the same IP subnet
as all other devices connected directly to your home router.
1) Connect second Ethernet cable from the LAN port on your POE to your home router.
2) Turn on the WiFi-enabled device(s) that you want to connect and scan for wireless
networks. It may take a few minutes for the network to appear.
3) The label located on the front of the Quick Start Guide or bottom of the unit has the
unique default SSID and password. Select this WiFi signal from the list of wireless
networks and connect. Once the correct SSID has been selected, enter the listed
password. We recommend you set your device(s) to automatically connect with the
Winegard Extreme 2.0.
4) Once connected, open an internet browser on your device and type 10.11.12.1 into the
address bar and press ENTER (Figure 8).
This will take you to the Admin Login screen (Figure 9).
Login using:
Username: admin Password: admin.
5) INTERNET ACCESS - Select Ethernet and press SELECT (Figure 10).
Your unit is connecting and will take about 2 minutes.
NOTE: WiFi signal will stay at No Signal until Connected, when using Access Point
or Bridge Modes.
6) NAVIGATE TO PAGE - Select Advanced Settings.
7) Under WAN Ethernet Identifier, select Default (Figure 11).
8) From the BRIDGING drop-down menu, select BRIDGE.
9) Select CHANGE WAN ID and the system will updated.
10) Internet Status will show Connected to Ethernet (Figure 12).
11) NAVIGATE TO PAGE - Select Advanced Settings.
12) Select Restart System.
You are ready to use the internet.
Figure 8
Figure 9
Figure 11
Figure 10
Figure 12
*NOTE: Factory Reset is required to
get the unit out of Bridge Mode. You
will need to power on the unit, wait 90
seconds and then power off. Repeat 3
consecutive times. On the next power
on, the system will begin a reset, this
process could take up to 5 minutes.
Operation - 5GHz Antenna Activation 7
5GHz Antenna Activation – Allows higher speed but reduces range.
1) Turn on the WiFi-enabled device(s) that you want to connect and scan for wireless
networks. It may take a few minutes for the network to appear.
2) The label located on the front of the Quick Start Guide or bottom of the unit has the unique
default SSID and password. Select this WiFi signal from the list of wireless networks
and connect. Once the correct SSID has been selected, enter the listed password. We
recommend you set your device(s) to automatically connect with the Winegard Extreme 2.0.
3) Once connected, open an internet browser on your device and type 10.11.12.1 into the
address bar and press ENTER (Figure 13).
This will take you to the Admin Login screen (Figure 14).
Login using:
Username: admin Password: admin.
4) INTERNET ACCESS – WIFI will need to be selected. Press SCAN FOR WIFI (Figure 15).
5) Enter the network password, if prompted (Figure 16). Once the Winegard Extreme 2.0
connects to the internet, the Internet Status will show CONNECTED. This could take as
long as two minutes. You are now ready to use the WiFi and will see your paired info in
Internet Status and strength in WiFi Signal.
Figure 13
Figure 14
Figure 16
Figure 15
Operation - 5GHz Antenna Activation (continued)
5GHz Antenna Activation – continued from previous page
6) Under NAVIGATE TO PAGE, select Local Network Settings
from the drop-down menu (Figure 17).
7) Under 5 GHz Network Settings, select ENABLE (Figure 18).
8) Select CONTINUE at bottom of screen.
9) You will be directed back to the Status page and close out
screen (Figure 19).
10) On your device (phone, tablet, etc.), go to Settings/WIFI and you
will now see the units 5GHz SSID broadcasting and select for
use (Figure 20).
11) Select the 5GHz connection and enter the password from the
Quick Start Guide or bottom of unit to connect.
You are now ready to use internet.
Figure 17 Figure 18
Figure 19 Figure 20
8
Operation - Guest Network
Guest Network -
From the Status Screen
1) Under NAVIGATE TO PAGE, select Local Network Settings
from the drop-down menu (Figure 21).
2) On the next screen, select ENABLE under Guest Network
Settings (Figure 22).
3) Give the guest network an easily recognizable name.
4) Enter a password - If you use a simple password, it is
recommended that the guest network be disabled when
not in use. Select CONTINUE (Figure 22).
5) You will be directed back to Status page and can now close out
the screen (Figure 23).
Your guests are now ready to use the WiFi.
Figure 21 Figure 22
Figure 23
9
Operation - NAVIGATE TO PAGE (Screens)
Page Summary -
The following screens are available under the NAVIGATE TO PAGE screen:
1) Local Network Settings - Used to select your WiFi connection, enable 5GHz connection,
change passwords, enable Guest Network, rename network ID’s and change security type.
2) Advance Settings - Used to set up Bridge Mode (Figure 25).
3) Saved WiFi Networks - Used to connect or delete stored networks.
4) Network Activity - Used to view connected devices and network traffic (Figure 24).
5) Update Software - Used to check for latest software updates, updating software, and
restoring to factory configuration (Figure 26).
6) Support - Key unit information, Winegard phone support number, email support address,
Save Log function, Test Speed and Test Connectivity (Figure 27).
7) About - Contains model number, software version, bootloader version, serial number,
MAC address and IP.
Figure 26
Figure 24
Figure 25 Figure 27
10
Otros manuales para ConnecT 2.0
1
Tabla de contenidos
Otros manuales de Antena de TV de Winegard
Winegard
Winegard Carryout GM-MP1 Manual de usuario
Winegard
Winegard SK-3003 Manual de usuario
Winegard
Winegard HD9095P Manual de usuario
Winegard
Winegard SENSAR VM-2200 Manual de usuario
Winegard
Winegard AIR 360+ Manual de usuario
Winegard
Winegard SK-3003 Manual de usuario
Winegard
Winegard SK-3005 Manual de usuario
Winegard
Winegard RoadTrip SDi Manual de usuario
Winegard
Winegard SENSAR GS-2200 Manual de usuario
Winegard
Winegard SENSAR GS-2200 Manual de usuario
Winegard
Winegard SK-3005 Manual de usuario
Winegard
Winegard SharpShooter SS-3000 Manual de usuario
Winegard
Winegard HD7084P Manual de usuario
Winegard
Winegard SS-3000 Manual de usuario
Winegard
Winegard MA1055W Manual de usuario
Winegard
Winegard TRAV'LER DIRECTV SK-SWM3 Manual de usuario
Winegard
Winegard TRAV'LER DIRECTV SK-SWM3 Manual de usuario
Winegard
Winegard FlatWave FL-5000 Manual de usuario
Winegard
Winegard RoadTrip Minimax RT8000S Manual de usuario
Winegard
Winegard RoadStar RS-3000 Manual de usuario
