Windsor CLP12 Manual de usuario

Read these instructions before operating the machine

MODEL: CLP12

Operating Instructions

98630 08/19/03

CARPET EXTRACTOR

TABLE OF CONTENTS

CLIPPER 98630 10/19/02

Data Log/Table of Contents..............1

Safety Instructions............................2

Grounding Instructions .....................3

Controls............................................4-6

Operations........................................7-13

Troubleshooting................................14

Wiring Diagram.................................15

Maintenance .................................... 16-18

Technical Specifications................... 19

Service Schedule. ............................ 20

Parts Lists........................................ 21-34

Spare Parts/Notes............................ 35

Warranty ....................................... 36

INSPECTION

Carefully unpack and inspect your machine for shipping damage. Each unit is operated and thoroughly inspected

before shipping, and any damage is the responsibility of the carrier, who should be notified immediately.

MODEL

DATE OF PURCHASE

SERIAL NUMBER

SALES REPRESENTATIVE #

DEALER NAME

SAFETY INSTRUCTIONS

CLIPPER 98630 12/14/98 2

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution

must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

This machine is for commercial use.

To reduce the risk of fire, electric shock, or injury:

Connect to a properly grounded outlet. See Grounding Instructions.

Do not leave the machine unattended. Unplug machine from outlet when not in use and before

maintenance or service.

Use only indoors. Do not use outdoors or expose to rain.

Do not allow machine to be used as a toy. Close attention is necessary when used by or near

children.

Use only as described in this manual. Use only manufacturer’s recommended components and

attachments.

Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding

the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or

dropped into water, return it to an authorized service center.

Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord

around sharp edges or corners.

Do not run machine over cord. Keep cord away from heated surfaces.

Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.

Do not handle the electrical plug or machine with wet hands.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce

airflow.

This machine is intended for cleaning carpet only.

Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

This machine is not suitable for picking up health endangering dust.

Turn off all controls before unplugging.

Machine can cause a fire when operating near flammable vapors or materials. Do not operate this

machine near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals,

factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

If foam or liquid comes out of machine, switch off immediately.

SAVE THESE INSTRUCTIONS

WARNING:

GROUNDING INSTRUCTIONS

CLIPPER 98630 12/14/98

THIS PRODUCT IS FOR COMMERCIAL USE ONLY.

ELECTRICAL:

In the USA this machine operates on a standard

15 amp 115V, 60 hz, A.C. power circuit . The amp,

hertz, and voltage are listed on the data label found

on each machine. Using voltages above or below

those indicated on the data label will cause serious

damage to the motors.

GROUNDING INSTRUCTIONS:

This appliance must be grounded. If it should

malfunction or break down, grounding provides a

path of least resistance for electric current to

reduce the risk of electric shock. This appliance is

equipped with a cord having an equipment-

grounding conductor and grounding plug. The plug

must be inserted into an appropriate outlet that is

properly installed and grounded in accordance with

all local codes and ordinances.

This appliance is for use on a nominal 115-volt

circuit, and has a grounded plug that

looks like the plug in “Fig. A”. A temporary adaptor

that looks like the adaptor in “Fig . C” may be used

to connect this plug to a 2-pole receptacle as

shown in “Fig. B”, if a properly grounded outlet is

not available. The temporary adaptor should be

used only until a properly grounded outlet (Fig. A)

can be installed by a qualified electrician. The

green colored rigid ear, lug, or the like extending

from the adaptor must be connected to a

permanent ground such as a properly grounded

outlet box cover. Whenever the adaptor is used, it

must be held in place by a metal screw.

Improper connection

of the equipment-

grounding conductor

can result in a risk of electric shock. Check with a

qualified electrician or service person if you are in

doubt as to whether the outlet is properly

grounded. Do not modify the plug provided with the

appliance - if it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

WARNING:

NOTE: In Canada, the use of a temporary adaptor is no

ermitted by the Canadian Electrical Cod

PROPER GROUNDING

Metal Screw

Adaptor

Grounded Outlet Box

Fig. A Fig. B

Fig. C

Tab For Grounding Screw

Grounded

Outlet

Grounding Pin

Adaptor

CONTROLS/COMPONENT LOCATIONS

CLIPPER 98630 12/14/98 4

1. Main Handle. Used to pull and maneuver

machine.

2. Handle Adjustment. Used to adjust height of

handle, and allow machine to be used in

“PUSH” or “PULL orientation.

3. Electrical Cord.

4. Solution Switch. Turns on pump. Continuous

position (bottom) activates electro-valve to

dispense solution to floor through jets.

Intermittent position (up) requires operator to

depress 1 of 3 trigger switches to dispense

solution. Center position is off.

5. Brush Motor Switch. Turns on brush motor.

6. Vacuum Motor Switch. Turns on vacuum

motor.

7. Trigger Switches. Activates electro-valve to

dispense solution to floor through jets when

solution switch is in the intermittent position.

8. Brush Motor Circuit Breaker. 6 amp.

Breaker protecting brush motor.

9. Vacuum Motor Circuit Breaker. 15 amp.

Breaker protecting vacuum motor.

10. Recovery Dump Hose. Facilitates draining

dirty cleaning solution.

8946

CONTROLS/COMPONENT LOCATIONS

CLIPPER 98630 12/14/98

1. Solution Accessory Tool Hookup. Used for

various auxiliary cleaning tools.

2. Vacuum Hose Door. Used to connect

various auxiliary 1 ½ inch cleaning tool

vacuum hoses.

3. Brush Height Adjustment. Used to regulate

brush height from storage position to various

carpet heights.

4. Recovery Tank. Used to collect dirty

cleaning solution.

5. Solution Tank. Used to hold cleaning

solution.

6. Solution Dump Hose. Facilitates draining

excess cleaning solution from solution tank.

7. Recovery Tank Dome.

8. Solution Tank Lid.

9. Solution Tank Fill Hose.

10. Vacuum Shoe.

11. Brush Housing.

12. Front Lifting Handle.

13. Cleaning Solution Filter. 4

CONTROLS/COMPONENT LOCATIONS

CLIPPER 98630 12/14/98 6

1. Solution Intake Cover.

2. Vacuum Intake Cover.

3. Float Shut-Off.

4. Clean-Out Opening.

5. Pour Spout.

6. Lift Handle.

FILLING OPERATIONS

CLIPPER 98630 12/14/98

FILLING THE CLIPPER

NOTE: Use clean bucket of water to fill solution tank

Do not put defoamer, solvents, spotter or

prespray chemicals in the solution tank.

Do not allow water to spill into vacuum motor inlet. Dry

spillage from top of solution tank before replacing

recovery tank.

CHEMICALS

Suitable Chemicals Non-Compatible Chemicals

Alkalis Aldehydes

Detergents Aromatic Hydrocarbons

Hydroxides SP Butyls

Soaps Carbon Tetrachloride

Vinegar Clorox*

Chlorinated Bleaches

Chlorinated Hydrocarbons

Lysol*

Methyl Ethel Ketone (MEK)

Perchorethylene (perc)

Phenolics

Trichlorethylene

D-Limonene

STEP

RECOVERY TANK

SOLUTION

TANK

Remove solution

tank lid

Replace solution

tank lid

dd cleaning

chemical

12 – 24oz.

(356ml – 711ml)

FILL LINE 140°F

(

60°C

)

12 gal.

(45.5 ltr.)

dd water

OPERATIONS

CLIPPER 98630 12/14/98 8

Remove electrical cord and literature

from recovery tank. Fill solution tank

(see filling instructions page 7).

djust brush to proper setting. Note:

For good operation the brush must

skim the carpet. If circuit breaker

trips raise brush to prevent damage

to motor or carpet.

Plug cord into grounded outlet. Note:

Be sure dome is seated on recovery

tank, and float shut-off is installed

correctly.

Turn on brush and vacuum motor

switches (“ON”=“I”). Turn on solution

switch for continuous spray or set

switch to intermittent to allow use of

trigger switches.

STEP

CORRECT

INCORRECT

1/8in

(3mm)

SOLUTION VACUUM

CONT

INT BRUSH ONON

OPERATIONS

CLIPPER 98630 12/14/98

Select continuous setting to start

solution spray or select intermittent

setting to enable use of trigger

switches to start solution spray.

The intermittent setting requires the

operator to hold any one of the

three trigger switches in the “on”

position with the fingers, and is

typically used in small areas where

short cleaning passes are made.

The continuous setting allows the

operator to set the switch in the “on”

position with one touch, and is

typically used in large areas where

long cleaning passes are made.

Lower machine to floor.

djust handle to comfortable

operating position. Tip machine

back by main handle to move to

starting point.

STEP

INT

CONT

Otros manuales para CLP12

Tabla de contenidos

Otros manuales de Máquina de piso de Windsor

Windsor

Windsor DOMINATOR D250 Manual de usuario

Windsor

Windsor 1.005.293.0 Manual de usuario

Windsor

Windsor Saber Glide 86037580 Manual de usuario

Windsor

Windsor PRESTO! PRSIFB2 Manual de usuario

Windsor

Windsor ADMIRAL ADM8IA - 10080010 Manual de usuario

Windsor

Windsor VOYDU1, VOYXDU 10086130 Manual de usuario

Windsor

Windsor COMMODORE CMD Manual de usuario

Windsor

Windsor COMDU 1.008-612.0 Manual de usuario

Windsor

Windsor Lightning Battery Burnisher 10027100 Manual de usuario

Windsor

Windsor Saber Glide 30 Manual de usuario

Windsor

Windsor PJ2A Manual de usuario

Windsor

Windsor U1500 Manual de usuario

Windsor

Windsor EXPERT Manual de usuario

Windsor

Windsor MERiT 2000 Manual de usuario

Windsor

Windsor Clipper Duo Manual de usuario

Windsor

Windsor ADMIRAL ADM8IA - 10080010 Manual de usuario

Windsor

Windsor ADMIRAL Admiral 8 Manual de usuario

Windsor

Windsor VOYAGER 2 Manual de usuario

Windsor

Windsor ADMIRAL ADM8 10080170 Manual de usuario

Windsor

Windsor COMPASS CMPS 10070050 Manual de usuario

Windsor

Windsor Saber Compact 16SP Manual de usuario

Windsor

Windsor Commodore 20 Manual de usuario

Windsor

Windsor RRB 360 T Manual de usuario

Windsor

Windsor CB20 Manual de usuario

Manuales populares de Máquina de piso de otras marcas

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manual de usuario

Numatic

Numatic ET 4045 Manual de usuario

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manual de usuario

Mytee

Mytee 8070 Mytee-Lite Manual de usuario

Kärcher

Kärcher B 140 R Manual de usuario

Triple S

Triple S Ace 26T1 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance SW 750 Manual de usuario

Tornado

Tornado Marathon 2000 98190 Manual

Numatic

Numatic TTB 1117/100 Manual de usuario

Tennant

Tennant 8210D Manual de usuario

Nobles

Nobles Frontier Manual del producto

lavina

lavina 21-X Manual de usuario

KENT

KENT Edge 28B Manual de usuario

Tennant

Tennant 215 Manual del producto

CleanFreak

CleanFreak DURA-18HD Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guía del administrador

BETCO

BETCO PB24 Manual de usuario

IPC

IPC CT51-71 BT Manual de usuario