WilTec 61495 Manual de usuario
Operation Manual
lawn trimmer
61495, 61496
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ
insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik mbH Seite 20
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
The information contained in this document is subject to change without prior notice. o part of this
document can be copied or duplicated in another form without the prior written consent of WilTec
Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in
this user manual or the connection diagram.
Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual
is complete, accurate and updated, errors cannot always be avoided. In the event of problems with
this user manual please complete and send this form back to us.
FAX-notification (+++49 2403 55592-15),
from: ________________________________________
Name: ________________
Firm:_____________________
Tel/Fax:__________________
I would like to report the following mistakes:
_______________________________ ____________________________________
Customer Service WilTec Wildanger Technik GmbH
e-mail: [email protected]
Tel:++ +49 2403 55592-0
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury by means of fire or
electric shock we urge that our clients take some basic safety precautions when using this
device. Please read the operation instructions carefully and make sure you have understood its
content.
Always use a grounded power connection with the appropriate mains voltage. You can find the
corresponding mains voltage on the type plate. If you have any doubts about the connection being
grounded, have it checked by a qualified professional. ever use a faulty electric cable.
Do not inspect the electrical part of the pressure pond filter in a wet or damp environment or when you
are wet yourself and protect it from direct sunlight. Install this device in a safe location so that nobody
can step on the cable, fall over or damage it. Disconnect the power plug before cleaning it and use
only a damp cloth for cleaning. Avoid using cleaning agents and make sure that no liquid enters the
electrical part of the pump.
The electric part of the device contains no parts that can be inspected or serviced by the user. Leave
the maintenance, adjustment and repair to qualified technical personnel. In case of unauthorised
intervention the 2-year warranty is no longer valid! Keep these operation instructions safe.
© by WilTec Wildanger Technik mbH Seite 21
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Notes on types of warnings in the manual
This mark indicates instructions which must be followed in order to prevent accidens
which could lead to serious bodily injury or death.
This mark indicates instructions which must be followed, or it leads to mechanical fail-
ure, breakdown, or damage.
This mark indicates hints or directions useful in the use of the product.
Contents
1. Warning Labels on the machine
2. Parts location
3. Symbols on the machine
4. Safety precautions
5. Set Up
6. Fuel
7. Operation
8. Maintenance
9. Specification
1. Warning label on the machine
(1) Read owner‘s manual before operating this machine
(2) Wear head, eye and ear protection
(3) Warning/Attention
(4) Keep all persons 15 meters away from the brush cutter
© by WilTec Wildanger Technik mbH Seite 22
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
If warning seals peel off or become soiled and impossible to read, you should contact
the dealer from which you purchased the product to order new seals and affix the
new seal in the required location.
ever remodel your brush cutter. We won‘t warrant the machine, if you use the re-
modeled brush cutter or you don‘t observe the proper usage written in the manual.
2. Parts Location
1. Fuel tank
2. Starter
3. Air cleaner
4. Stand
5. Engine switch button
6. Housing
7. Hanger
8. Handle
9. Hale bracket
10. Throttle lever
11. Throttle cable
12. Outer pipe
13. Safety guard
14. Gear case
15. Blade
© by WilTec Wildanger Technik mbH Seite 23
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
3. Symbols on the machine
For safe operation and maintenances, symbols are carved in relief on the machine.
According to these indications, please be careful not to make a mistake.
( a) The port to refuel the „MIX GASOLI E“
Position: fuel tank cap
( b) The direction to close the choke
Position: AIR CLEANER COVER
( c) The direction to open the choke
Position: AIR CLEANER COVER
4. Safety Precautions
Before using the device
a. Read this owner‘s manual carefully to understand how to operate
this unit properly
b. This product has been designed for use in cutting grass, ad it
should never be used for any other purpose.
c. You should never use the product when under the influence of al-
cohol, when suffering from exhaustion or lack of sleep.
d. Avoid running the engine indoors. The exhaust gases contain
harmful carbon monoxide
e. ever use the product under circumstances like those described
below:
1. When the ground is slippery or when other conditions exist which
might make it not possible to maintain a steady posture
2. At night, at times of heavy fog, or at any other times when your
field of vision might be limited and it would be difficult to gain a clear
view of the area.
3. During rain storms, during lightning storms, at times of strong or
gale- force winds, or at any other times when weather conditions
might make it unsafe to use this product.
f. When using this product for the first time, learn to handle it from
skilled worker.
g. Lack of sleep, tiredness, or physical exhaustion results in lower at-
tention spans, and this in turn leads to accidents and injury. Limit the
amount of time of using the machine continuously to somewhere
around 10 minutes per session and take 10~20 minutes of rest be-
tween work-sessions.
© by WilTec Wildanger Technik mbH Seite 24
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Also try to keep the total amount of work performed in a single day under 2 hours or
less.
1. Be sure to keep this manual handy so that you may refer to it later whenever any
questions arise.
2. ever allow children or anyone unable to fully understand the directions given in
this manual to use this brush cutter.
Working gear and clothing
a. When using the product, you should wear proper clothing
and protective equipments as follows.
( 1) Helmet
( 2) Protection goggles or face protector
( 3) Thick work gloves
( 4) Non-slip-sole work boots
( 5) Ear protectors
b. And you should carry with you
1. Description
2. Properly locked fuel tank
3. Spare blade
4. Things to notify your working area (shutter band,
warning signs)
c. ever use the product when wearing pants with loose
cuffs, when wearing sandals, or when barefoot.
Working considering handling of fuel
a. The engine of this product is designed to run on a mixed fuel which
contains highly flammable gasoline. ever store cans of fuel or refill
the fuel tank in any place where there is a boiler stove, wood fire, elec-
trical sparks, welding sparks, or any other source of heat or fire which
might ignite the fuel.
b. Smoking while operating the product or refilling its fuel tank is extremely danger-
ous. Always be sure to keep lit cigarettes away from the product at all times.
c. When refilling the tank always turn off the engine first and take a careful look
around to make sure that there are no sparks or open flames anywhere nearby be-
fore refueling.
d. If any fuel spillage occurs during refueling, use a dry rag to wipe up spills before
turning the engine back on again.
e. after refueling, screw the fuel cap back tightly onto the fuel tank and then carry the
product to a spot 3 m or more away from where it was refueled before turning on the
engine.
© by WilTec Wildanger Technik mbH Seite 25
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Things to check before using your brushcutter
a. Before beginning work, look around carefully to get a feel for the shape of the land
or grass to be trimmed and whether or not there are any obstacle which might get in
the way white working, and remove any obstacles,
which can be cleared away.
b. The area within a perimeter of 15m of the person us-
ing the brush cutter should be considered a hazardous
area into which no one should enter while the brush
cutter is in use, and when necessary yellow warning
rope, warning signs should be placed around the work
area. When work is to be performed simultaneously by
two or more persons always check the presence and
locations of others so as to maintain a distance each
person.
c. Make sure that there are no loose screws or bolts.
fuel leaks, ruptures, dents, or
any other problems, which might interfere with safe op-
eration. Be especially careful to check that there is
nothing wrong with the blades or with the joints by
which the blades are attached to the brush cutter.
d. ever use blades that are bent, warped, cracked,
broken or damaged in any way.
e. Keep the blade always sharp.
f. Filling the cutting edges, keep the end corner sharp
and round the root of the edge.
g. Check the boll to fasten the blade and be sure the
blade turns smoothly without abnormal noise.
Notes on starting the engine
1. Take a careful look around to make sure that no obstacles exist within a perimeter
of 15m or less around brush cutter.
2. Place the body of the brush cutter onto the ground in a flat clear area and hold it
firmly in place so as to ensure that neither the blades nor the throttle come into con-
tact with any obstacles when the engine starts up.
3. Place the throttle into the idling position when starting the engine.
4. After starting up the engine, if the blades continue to rotate even after the throttle
has been moved fully back, turn off the engine and check the throttle wire and other
parts.
Kickback safety precautions
A dangerous reaction may occur when the spinning blade contacts a solid object in
the critical area. It is called kickback. as a result, the operator can lose control of the
unit, which can cause serious or fatal injury. Avoid kickback, observe the safely pre-
cautions below strictly:
© by WilTec Wildanger Technik mbH Seite 26
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
1. Before beginning work, clear your working area.
2. When using your brush cutter do not grip other parts except the handles.
3. When using your brush cutter never take your eyes off, if you need to place
the throttle into the idling position.
4. When using your brush cutter do not let the unit get close to your feet nor
raise the unit above your waist
Transportation
1. Make sure the appropriate blade cover is in place.
2. When transporting by car fix the unit firmly using a rope, do not transport by bicy-
cle or motorcycle because it is dangerous.
3. ever transport the brush cutter over rough roads over long distances without first
removing all fuel from the fuel tank, as doing so might cause fuel to leak from the
tank.
Operation safety precautions
1. Grip the handles of the brush cutter firmly with both hands. If you suspend the
work, place the throttle into the idling position.
2. Always be sure to maintain a steady even posture while working.
3. Maintain the speed of the engine at the level required to perform
cutting work and never raise the speed of the engine above the
level necessary.
4. If the grass gets caught in the blade during operation or if you
need to check the unit or refuel the tank always be sure to turn off
the engine.
5. If the blade touches a hard object like a stone immediately stop
the engine and check if something is wrong with the blade. If so re-
place the blade by new one.
6. If someone calls out while working always be sure to turn off the
engine before turning around.
7. ever touch the spark plug or plug cord while the engine is in
operation. It may result in being subjected to an electrical shock.
8. ever touch the muffler spark plug or other metallic parts of the
engine while the engine is in operation or immediately after shut-
ting down the engine. Doing so may result in serious burns.
9. When you finish cutting in one location and wish to continue
work in another spot turn off the engine and turn the unit as the
blade faces away from your body.
Maintenance safety precaution
1. Perform the maintenance and checking operations described in this manual at reg-
ular intervals. If any parts must be replaced or any maintenance or repair work not
described in this manual must be performed please contact a representative from the
store nearest authorized servicing dealer for assistance.
© by WilTec Wildanger Technik mbH Seite 27
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
2. Under no circumstances should you ever take apart the brush cutter or alter it in
any way. Doing so might result in the brush cutter becoming damaged during opera-
tion or the brush cutter becoming unable to operate properly.
3. Always be sure to turn off the engine before performing any maintenance or
checking procedures.
4. When sharpening removing the blade with proper tools and equipment to prevent
injury.
5. When replacing blade or any other parts or when replacing the oil or any lubricants
always be sure to use only products which have been certified by for use with the
brush cutter.
5. Set up
Engine and main pipe
Align the hanger and the fuel tank using attached 4 socket screws secure the con-
nection firmly with equal force.(F1)
(1) Fuel tank
(2) Molt
(3) Main pipe
Handle
1.Loosen the 4 bolts on the handle bracket.(F2)
2.Insert the right handle (throttle lever is at-
tached) and the left handle assembly into the
bracket and retighten the bolts
securely.(F2)
(1) Handle bracket
(2) Right handle
(3) Bolt
(4) Left handle
(5) Engine side
Safety guard
Attach the safety guard to the gear case and fix it
with the clamp and 2 bolts (M5*25) securely.(F3)
(1) Bolt
(2) Clamp
(3) Main pipe
(4) Safety guard
© by WilTec Wildanger Technik mbH Seite 28
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Throttle wire
After fitting up the wire make sure that the throttle
cable is put in the throttle lever. If not it is very dan-
gerous because the engines rotate after releasing
the throttle.
1. Hook the cable end into the hole of the throttle
lever. And set the cable in the lever as shown in the
picture.(F4)
2. Wrap the band so as the throttle wire is fixed with
the handle.
(1) Hole
(2) Throttle cable
Adjusting the throttle cable
1. after releasing the throttle lever pull the throt-
tle wire. The normal play is 1 or 2 mm when
measured at the carburetor side end.
2. If the play is short or long take off the air
cleaner cover loosen the lock nut and adjust the
play.(F5)
(1) Adjust nut
(2) Lock nut
Installing the metal blade (F6)
1. Set the inner holder to the gear shaft and fix
with the attached L-shaped bar.
2. Put the blade on the inner holder with letters to
the gear case and match correctly the hole of the
blade
to the projection of the inner holder.
3. Set the outer holder to the gear shaft with the
hollowed face to the blade.
4. Put the attached bolt cover on the outer holder
and secure it with the bolt (left screw) together
with the spring washer and the washer.
(1) ut
(2) Spring Washer
(3) washer
(4) Outer holder
(5) Blade
(6) Gear shaft
(7) Bar
(8) Inner holder
(9) Gear case
© by WilTec Wildanger Technik mbH Seite 29
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Otros manuales para 61495
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Recortadora de WilTec
