WIKA CEP6500 Manual de usuario

Operating Instructions

Universal Calibrator, Model CEP6500

Operating Instructions for Univeral Calibrator, Model CEP6500 EN

WIKA operating instructions, Model CEP6500

1. Introduction 5

Foreword 5

Notice 5

Trademarks 5

Safety 5

General Warnings 5

Electrical Warnings 5

Cautions 6

Summary of Functions 6

2. CEP6500 Hardware Parts & Accessories 7

2.1 Unpacking & Inspection 7

2.2 Operational Sections and Connections 8

2.2.1 The Terminal Connections 8

2.2.2 The Key Pad 16

2.2.3 The Display 17

2.2.4 The USB Connection 17

2.2.5 Stand for Table Top Use 17

2.3 Power Options 18

2.4 Battery 18

2.4.1 Charge time 19

2.4.2 Operating Time 19

3. Start Up & Basic Operations 20

3.1 Power ON or OFF 20

3.2 The User Interface 20

3.2.1 The Status Bar 21

3.2.2 The Function key Bar 22

3.2.3 Display Mode 22

3.2.4 Display Operations 30

3.2.5 SCR1 and SCR2 Key Option: mQUICK-SETUP Key 35

4. Menu Layout 36

4.1 MENU page 36

4.2 MEASURE Page 36

4.3 SOURCE Page 39

4.3.1 ET Setup 39

Contents

WIKA operating instructions, Model CEP6500 3

4.3.2 TC Setup 45

4.3.3 RTD Setup 50

4.3.4 Pulse Setup 55

4.4 DISPLAY Page 56

4.4.1 EM Display Settings 57

4.4.2 Switch test Display Settings 58

4.4.3 ET Display Settings 59

4.4.4 TC Display Settings 60

4.4.5 RTD Display Settings 62

4.5 DATA LOGGING Page 64

4.5.1 Transferring the Results to a Personal Computer 66

4.6 CJC SETTING Page 67

4.7 WireSelectPage 68

4.8 Alarm Page 69

4.9 SETTING Page 70

4.9.1 HART Settings 70

4.9.2 Display Settings 71

4.9.3 Date/Time Settings 71

4.9.4 Calibration 72

4.9.5 Battery Info. 85

4.9.6 Set Password 85

4.9.7 Factory Reset 85

4.9.8 AboutUs 85

5. Maintenance & Troubleshooting 86

5.1 Common Problems 86

5.2 Replacing the Battery 86

5.3 Related Information 87

5.3.1 Thermocouple Measurement/Simulation, Connections and troubleshooting 87

5.3.2 Parallel Functions in CEP6500 90

  

  

6.2 Display & Keys 92

6.3 Special Features 92

6.4 Power Supply 92

6.5 Physical 92

6.6 Electrical Measurement Parameters andAccuracy 93

Contents

WIKA operating instructions, Model CEP6500

6.7 Electrical Simulation Parameters and Accuracy 93

6.8 Resistance Measurement 0...4000 ohm 93

6.9 Resistance Simulation 0...4000 ohm 93

6.10 RTD Measurement and Simulation 93

6.11 Available RTD Types 94

6.12 Thermocouple /mV Resolution and Accuracy 95

6.13 Frequency Measurement 95

6.14 Pulsecounting 95

6.16 FrequencyGeneration 95

6.17 Pulse Generation 96

6.18 Enclosure Dimensions 97

7. Disposal 98

Contents

WIKA operating instructions, Model CEP6500 5

1. Introduction

Foreword Thank you for purchasing Universal Calibrator CEP6500. The

CEP6500 calibrator is compact hand-held calibrator with an easy

to use graphical user interface. This manual describes the basic

functions and operation methods. Please read through this user’s

manual carefully before using the product.

Notice The contents of this manual are subject to change without notice as

a result of continuous improvements to the instrument’s performance

and functions.



this manual. Should any errors or omissions come to your attention,



Under no circumstances may the contents of this manual, in part or

in whole, be transcribed or copied without our permission.

Trademarks Our product names or brand names mentioned in this manual are

the trademarks or registered trademarks Of WIKA Instruments India

Private Limited. (Herein after referred to as WIKA) Adobe,

Acrobat, and Postscript are either registered trademarks or

trademarks of Adobe Systems Incorporated. All other product

names mentioned in this user’s manual are trademarks or registered

trademarks of the respective companies.

Safety Before you use the instrument, make sure that you read and

understand all the related data. This includes: the applicable local

safety procedures, this publication, And the instructions for the

accessories/options/equipment you are using it with.

Cleaning For Cleaning Use Soft cloth without water

WARNING

General  

Warnings related accessories.

Donotusetheinstrumentoraccessoryifitisnotinitsnormalcondition.

Use the applicable protection and obey all safety precautions. Do

not use the instrument in locations with explosive gas, vapor or dust.

There is a risk of an explosion

Electrical To prevent electrical shocks or damage to the instrument, do not

Warnings connect more than 30V between the terminals, or between the

terminals and the ground.

This instrument uses a Lithium-Ion battery pack. To prevent an



it safe from damage. For operating conditions, see section 6.1 on

Page-85.

WIKA operating instructions, Model CEP6500

To prevent battery leakage or heat generation, only use the battery

charger in the temperature range 0 to 45°C (32 to 113°F). For

operating conditions, see section 6.1 on Page-85.

To make sure the display shows the correct data, disconnect the test

leads before you set the power to on or change to another measure

or source function.

Cautions To prevent damage to the display, do not use sharp objects on the

screen.Before you start an operation or procedure in this publication,

make sure that you have the necessary skills (if necessary, with



engineering practice at all times.

When Replacing Battery replace with the same type of battery (3.7V

/3000Ah) from the Manufacturer ONLY.

The connector for battery connection is polarized. Please correctly

connect or disconnect the connector to the charger board.

In case there is battery leakage, Replace as per above instruction.

Summary of This table gives a summary of the available functions with the

Functions CEP6500 calibrator.

Function

Easy to read liquid crystal display (LCD) in color

Rechargeable lithium Ion battery with enhanced power control for

prolonged battery life.

* Measure RTD (Pt10, Pt50, Pt100, Pt200, Pt400, Pt1000, Pt100

(3926),Ni100 (672), Ni100 (618), Ni120 (672), Cu10 (427),

Cu50 (427), Cu100 (427)), Resistance (0to4000ohms), mA,

mA (2W), Thermocouple (E,J,K,T,B,R,S,N), mV (-10to 250mV),

Switch-test, Frequency, Pulse

* Simulate RTD (Pt10, Pt50, Pt100, Pt200, Pt400, Pt1000, Pt100

(3926), Ni100 (672),Ni100 (618), Ni120 (672), Cu10 (427),

Cu50 (427), Cu100 (427), Resistance (0 to 4000

ohms),Thermocouple (E,J,K,T,B,R,S,N), mV (-10to250mV), mA

mA(2W), V, Frequency, Pulse

Step/Ramp functions: Automatic/Manual

Universal Serial Bus (USB) communications ports: For computer

Communications, Battery Charging& Firmware Upgrade

Data Logging

Other functions:



alarm indication (on the display and buzzer), Glance Screen.

Continuity Test,Automatic/Manual Wire Selection for RTD

Measurement, RTD CJ Compensation.

*Refer to the Specication Sheet on Page: 95

WIKA operating instructions, Model CEP6500 7

2. CEP6500 Hardware Parts & Accessories

2.1 Unpacking & Inspection

At the factory each new CEP6500 passes a careful inspection.It should be free of scrapes

and scratches and in proper operation order upon receipt.The receiver should, however,

inspect the unit for any damage that may have occurred during transit. If there are signs

of obvious mechanical damage, package contents are incomplete, or the instrument

           

soon as possible. The standard accessories are as follows:

Sr. No Description Qty

1.  1

2. CEP6500 user guide 1

3. 4mm to 4mm banana cable Red, 100cm 3

4. 4mm to 4mm banana cable Black, 100cm 3

5. Crocodile clip Red 3

6. Crocodile clip Black 3

7. Test lead Cu-Cu (Miniature TC Plug Cutypeto 4mm Test lead) 1

8. USBA to mini USBB type cable for PC

communication and charging

9. 5V1 A charging adaptor 1

If you have to return the instrument to the factory for any reason, use the original

packing whenever possible. Include a detailed description of the reason for the return.

WIKA operating instructions, Model CEP6500

2.2 Operational Sections and Connections

All sections and connections are presented in detail on the next pages.

Note:

1Terminal Connection For

Measure & Source

2Keypad Section

3TFT Color Display

USB Connection Slot for PC

Communication & Charging

Keep in mind that the next picture (as well as all pictures of CEP6500 in this manual)

has an example con guration of modules. The con guration of your CEP6500 may

vary signi cantly from the one in the picture.

2.2.1 The Terminal Connections

WIKA operating instructions, Model CEP6500 9

EM (Electric Measurements and 24V Supply) Measure Terminals

Input Terminals for measuring voltage, current, supplying loop power, and Frequency

no. 95 Section 6.6 and page no. 97

Section 6.13, 6.14.

Current Measurement

CEP6500 supports current measurement using either CEP6500 as the loop power

supply while at the same time measuring the current or simply measuring the current

while an external power supply is used.





mA Current Measurement

In this mode CEP6500 not providing any supply voltage. For proper measurement the

external device should capable of providing the voltage supply. If the external device

should not capable, an external Power Supply should be connected in series.

WIKA operating instructions, Model CEP6500

mA Read Power Current Measurement

In this mode CEP6500 works as Loop Power Supply while at the same time measuring

the current.

Voltage Measurement

CEP6500 is capable of voltage measurement. The following picture displays the

connection for voltage measurement.

Frequency Measurement

CEP6500 is capable of frequency measurement. The following picture displays the

connection for frequency measurement.

Also check the Trigger Level setting.There you can specify the trigger level and whether

to use a test voltage during the frequency measurement

Tabla de contenidos

Otros manuales de Equipo de prueba de WIKA

WIKA

WIKA CTD9100-ZERO Manual de usuario

WIKA

WIKA Pascal ET Manual de usuario

WIKA

WIKA CPH7000 Manual de usuario

WIKA

WIKA DELTA-comb DPGS40TA Manual de usuario

WIKA

WIKA CTD9350 Manual de usuario

WIKA

WIKA CalibratorUnit CPU6000 Series Manual de usuario

WIKA

WIKA mensor CPG2500 Manual de usuario

WIKA

WIKA CPH65I0 Manual de usuario

WIKA

WIKA CPH7650 Manual de usuario

WIKA

WIKA CEP6000 Manual de usuario

WIKA

WIKA CPB 5000 Manual de usuario

WIKA

WIKA CPH6000 Manual de usuario

WIKA

WIKA Wally Box III CPH7600 Manual de usuario

WIKA

WIKA CEP1500 Manual de usuario

WIKA

WIKA NETRIS 3 Manual de usuario

WIKA

WIKA CPP 3000-X Manual de usuario

WIKA

WIKA CTD9100 series Manual de usuario

WIKA

WIKA CPB3500 Manual de usuario

WIKA

WIKA CPB3800 Manual de usuario

WIKA

WIKA CPH7000 Manual de usuario

WIKA

WIKA CPD8500 Manual de usuario

WIKA

WIKA CalibratorUnit CPU6000 Series Manual de usuario

WIKA

WIKA CEP1000 Manual de usuario

WIKA

WIKA CPB 5000 DP Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario