whi STACKA SBLY-1403.S Hoja de instrucciones
Thank you for purchasing this WHI Safeguard Product.
It is essential that you read these instructions
carefully before operating this product for the
first time.
Please retain these instructions for future reference.
The illustrations shown are for illustrative purposes only.
Barrier Safety Lamp
PRODUCT INSTRUCTIONS
1. Installing / Removing Batteries
1. Remove screws from the underside of the
lens body with your screwdriver and lift the lens
two inches.
2. Grip, twist and pull battery cap away from the base.
3. Insert two AA batteries as featured.
4. Align the lip and groove, then replace battery cap.
Twist to secure cap.
5. Replace lens and secure screws.
2. On/Off Button
1. Press once to activate flashing light, press twice
for static/steady and a third time to switch off.
WHI Safeguard’s innovative lighting solution is designed
to fit quickly and securely to all types of roadside barriers
and other industrial applications. This photocell activated
product provides 360 degree flashing or steady light with
prolonged battery life.
TECHNICAL DETAILS
Model No.
SBLY - 1403.S
* Uses 2 x AA standard alkaline batteries (not included)
* Illumination Type - LED x 4, yield of minimum 1100 mCd
* Flash Pattern - 30 per minute (single flash)
* Duration of Flash - 200 Milliseconds
* Classification L1, EN 12352:2006
Do not short-circuit battery terminals.
Do not allow any part to come into contact with
heat or a direct flame.
Do not allow water to come in contact with
batteries or wiring.
For maximum performance, use good quality
batteries.
Phillips screwdriver required for battery
installation.
WARNING: This product is not a toy.
Keep out of reach of small children and pets.
Do not look directly at the LED Lights.
At the end of its useful life, batteries must be
removed from the product and disposed of
appropriately.
ON / OFF Button
Note the correct polarity (+ or -).
+
+-
-
Groove
STACKA
TM
3. Installing lamp module
4. Position the lamp
We warrant the product against defects in materials and workmanship,
under ordinary consumer use, on delivery and for a period of 12 months from
the date of delivery. If the product proves defective during the warranty
period, we will ask you to follow the instructions for returning the product
that we will provide you with, and we will take one of the following actions:
(1) Replace the product with one that is the same or equivalent to the
product you purchased; (2) Repair the product; (3) Refund to you the
whole of or part of the purchase price of the product. Due to product
advancement and product availability, the replacement product may differ
slightly and may have a lower selling price from the original product you
purchased. MADE IN CHINA
Warranty Information
Manufacturer Address
WHI Safeguard Limited
57 Worcester Road, Bromsgrove,
B61 7DN
T. 44 (0) 1753 325 101
WHI Safeguard is a registered trademark
Place in position with the lens at the top,
then fasten with the security screws and
tool provided.
Align and position the lip on
the bottom of the module
with the grooves in the base.
PLEASE NOTE
Insert the lamp module and twist into
position, then fasten security screw
from the underside with the tool provided.
The module must be positioned with
the grooves to fasten securely.
Otros manuales de Equipo de iluminación de whi
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
