Wen DS164 Manual de usuario

INSTRUCTION MANUAL

UNPACKING YOUR SANDING DRUM KIT

MODEL DS164

SANDING DRUM KIT

Sanding Drums 80-Grit Sanding Sleeves

1 2 3 4

5 6 7 8

120-Grit Sanding Sleeves

9 10 11 12

The tools listed below are not included but are required for either assembly or adjustment.

• Open-End Wrench

• Slot-Head Screwdriver

NO. PART SIZE QTY

1 Sanding Drum 1.5" x 2" 1

2 Sanding Drum 1" x 1" 1

3 Sanding Drum 1" x 0.75" 1

4 Sanding Drum 0.5" x 0.5" 1

5 80-Grit Sanding Sleeve 1.5" x 2" 2

6 80-Grit Sanding Sleeve 1" x 1" 2

NO. PART SIZE QTY

7 80-Grit Sanding Sleeve 1" x 0.75" 2

8 80-Grit Sanding Sleeve 0.5" x 0.5" 2

9 120-Grit Sanding Sleeve 1.5" x 2" 2

10 120-Grit Sanding Sleeve 1" x 1" 2

11 120-Grit Sanding Sleeve 1" x 0.75" 2

12 120-Grit Sanding Sleeve 0.5" x 0.5" 2

THANKS FOR

REMEMBERING

INSTRUCTION MANUAL

KNOW YOUR SANDING DRUM KIT

Shank

Nut

Sanding Sleeve

ASSEMBLY & ADJUSTMENTS

ATTACHING THE SANDPAPER

1. Select a sanding drum (Fig. 1 - 1) and fit the corresponding sanding sleeve (Fig. 1 - 2) over the

rubber drum.

2. Turn the nut (Fig. 2 - 1) by using an open-end wrench (Fig. 2 - 2) to tighten the sandpaper against

the sanding drum.

NOTE: Once the nut is tightened, the sleeve should not be able to rotate freely. If needed, use the slot-

head screwdriver to hold the slot drive on the bottom of the drum while turning the wrench.

Fig. 1

1

2

ASSEMBLY & ADJUSTMENTS

INSTALLING INTO THE CHUCK

1. Place the chuck key (Fig. 3 -1) into the side

keyhole of the chuck (Fig. 3 - 2), meshing the key

with the gear teeth.

2. Turn key counterclockwise to open chuck jaws.

3. Insert sanding drum (Fig. 3 - 3) into the chuck so

the jaws grip as much of the shank as possible.

4. Center the sanding drum in the chuck jaws

before the final tightening of the chuck.

5. Tighten the chuck jaws using all three keyholes

of the chuck to ensure that the sanding drum will

not slip while sanding.

Fig. 3

Fig. 2

1

2

SPECIFICATIONS

Model Number

DS164

Maximum RPM 7500 RPM

Sanding Drum Sizes 1.5" x 2", 1" x 1", 1" x 0.75", 0.5" x 0.5"

Included Sandpaper Grits

80-Grit, 120-Grit

1

2

3

Manuales populares de Lijadora de otras marcas

Oliver

Oliver 6305 Manual de usuario

Jet

Jet 22-44 Pro-3 Manual de servicio

Makita

Makita M9204 Manual

Makita

Makita M9204 Manual de usuario

Craftsman

Craftsman 351.215131 Manual de usuario

Clarke

Clarke Woodworker CBS1-5B Manual de instrucciones

Chicago Pneumatic

Chicago Pneumatic CP9778 Manual de usuario

Nitto Kohki

Nitto Kohki BB-20 Manual de usuario

Ferm

Ferm FEOS-135 Manual de usuario

Unior

Unior 1510 Manual de usuario

stayer

stayer ls1200 Manual de usuario

Jet

Jet JSG-96 Manual de servicio

Parkside

Parkside PDS 290 B2 Manual de usuario

Status

Status XPA Series Manual de usuario

Clarke

Clarke EZ Sand Manual de usuario

Craftsman

Craftsman 113.22521 Manual de usuario

Craftsman

Craftsman 113.225831 Manual de usuario

CLAS

CLAS OP 1429 Manual de usuario