WEIGHSOUTH WS 10 Manual de usuario
WS 10
Weighing indicator
USER MANUAL
Edition:10052001A
Safety Instruction
For safety operation follow the safety instructions.
WARNING
WARNING
WARNING
Setting, Calibration Inspection and Maintain of the indicator is
prohibited by Non-professional sta.
Please make sure the weighing display have good ground in using
e indicator is the static and sensitive equipment,
cut o the power during electrical connections,
internal components touched by hand is prohibited,
and please take the measure of anti-static.
1. Technical Parameters
is weighing indicator is designed for bench scale. Floor scale,
the basic weighing function include: Hold. Print kg/lb conversion .
optional: I/O , 4-20mA output.
1.1 Main function
Weighing function:
Zero, tare, G.W, N.W, accumulation. printing, animal -weighing.
kg/lb convert. Overload remind.
Print format: S.N. G.W N.W Tare. Date, Time
1.2 Technical parameter
AC power AC100~250V
Operation temperatur - 10 °C ~ + 40 °C
Operation humidity ≤90%RH
Storage temperature - 40 °C ~ + 70 °C
Accuracy class 6000 e
Resolution display: 30, 000 ADC: 2,000,000
Zero stability error TK0 < 0.1μV//K
Span stability error TKspn < ± 6 ppm//K
Sensitivity (internal) 0. 3 μV /d
Input voltage -30~30mV DC
Excitation circuit 5 VDC, 4 wire connection,
Maximum connect 6 load cell of 350Ω
Options:
Pinter
RS232/RS485 serial interface or second display
I/O
4-20mA
Ensure that all parts are accounted for:
• WeighSouth WS10 Indicator
• Weighing Platform
• Column
• Wall Mount Bracket
• Required parts bag
• Operation manual
e correct location is crucial to the accuracy of the weighing
results. Select a stable, vibration-free and level location. e ground
must be able to safely bear the weight of the fully loaded scale.
1. Set the weighing platform on the selected level workplace
2. Aer rst removing the platter, loosen the shipping screws
located at each corner of the platform. ree full turns of
the screws is necessary. e scale will not function properly if
the shipping screws are touching the top sub assembly.
3. Attach the column to the underside of the bottom frame by
using the 4 hexagon head screws supplied. On certain models
choose which side of the weighing platform will better suit
your needs.
4. Tuck the load cell cable in the column and out the top of the
column.
5. Attach the indicator to the column using the umb screw
provided.
6. Attach the Load cell connector to the WS10 Indicator by lining
up the ports correctly.
1.3 Drawing
1. When you use the internal battery rst time, you should
charge the battery fully, to prevent low voltage resulted from
self leakage of battery.
2. When the “battery” light is on, means low battery.
3. e light turns to yellow during charging
4. When the light turns to green, means fully charged.
5. If the battery is not used for a long time, take it out to avoid
leakage
1.4 Battery instruction
2. Basic Operation
2.1 Keys
LED Instruction
Weighing data
kg kg
lb lb
Hold Data hold
Gross Gross weight
Net Net weight
Tare tare
Keys Key Name Key function
Print
1. Work with “ZERO” TARE” “ON/OFF” key
to perform many functions.
2. Print
Zero Zero the weight within tolerance
Tare At G.W mode, get the tare weight. At
N.W mode, clear the tare, get the G.W
GrossWeight At N.W mode, check the G.W, aer 3
seconds back to N.W automatically
Counting Counting operation
Kg/lb Convert Convert between kg and lb
Accumulation
1. Accumulation
2. work together with “ Print” to perform
e accumulation function and check the
accumulation result
Power On/O Press 2 seconds to power on or power o
Keys function
e weighing data is stable
Weight is zero
Hi Overload
OK Ok
Lo Underload
.Decimal
PCS Show the counting status
TOTAL Go to accumulation mode
2.2
Power on & o
Press 2 seconds to power on or power o, aer power on the
indicator show ”000000-999999”.
2.3 Zero operation
1. Initial zero setting:
When power on the indicator, if the weight on the scale
is within the initial zero tolerance, indicator show zero
automatically.
2. Manually Zero setting:
When the scales is stable, and not the negative display, you can
zero the weight within tolerance by press key.
2.4 Tare operation
Press “TARE” key, the gross weight is tared, indicator shows
the Net weight, the “Net” “tared” status light is on. At tare mode,
Press” TARE” key, clear the tare weight, the indicator will show the
gross weight.
2.5 Accumulation operation
At Zero mode, load weight till stable, Press go to accumulation mode,
”Total” light on, display” n 001”, and then display loaded weight; unload
the weight, back to zero, load the second weight again till stable.
Press display”n002” then display the second loaded weight. Repeat
Check the accumulation
Press “PRINT “key and hold it then press “TOTAL”” key,
display ”n**”, (it is the accumulating times) then show total weight.
there are 8 digits totally. It shows the rst 4 digits then the last
4 digits. For example, the rst 4 digits is”0012”, the last 4 digits
is”34,56” It means the actual weight is “1234.56”
it agin and again, maximum 999 times.
EXIT the accumulation function
When the indicator show the last 4 digits, Press hold it, the
indicator shows “clrn”, it means don’t clear the total Weight, Press
“PRINT” key to exit it; if you want to clear total weight, Press
“ZERO” or “TARE” key, “clrn” change to “clry” it means clear total
weight, then Press “PRINT” to clear the total weight and exit ac-
cumulating mode.
2.6 Print
2.7 Hold
2.8 COUNT
If the weighing is stable, aer connected with printer press
”PRINT” can print the weight. Note: at tare mode, print with tare.
If negative weight, cannot print. Set C30 for time format.
ere are two dierent hold functions. Peak hold function
and data hold function the setting is dierent accordingly.
C11=3 Automatic hold function
C11=0 close hold function.
1. At weighing mode, load the weights on the platform scales,
Press ”Count” the indicator show” PCS 0” press” Zero” key
input the quantity and press” Print” to conrm it.
2. Load the goods on the platform scales and then the indicator
will show the quantity.
3. Press” Count” back to weighing mode.
4. If you want to weigh dierent goods, at weighing mode, put
the sample on the platform scales, press” Count” the indicator
show ”0” Press “ Count” hold it and then press “ ON/OFF”
the indicator show” PCS 0”, press “Zero” input the sample
quantity, press “ Print” to conrm it. en repeat the step 2
and 3.
Tabla de contenidos
