Weber Rescue Systems SPS 270 MK2 Manual de usuario
E
Operang Instrucons
Baery rescue tools
1103421
www.weber-rescue.com
1.1 Informaon on the operang instrucons 4
1.2 Explanaon of symbols 5
1.3 Limitaon of liability 6
1.4 Copyright 6
1.5 Warranty provisions 7
1.6 Customer Service 7
2.1 Intended use 8
2.2 Operator responsibility 10
2.3 Operang personnel 11
2.4 Personal protecve equipment 12
2.5 Parcular hazards 13
2.6 Conduct in dangerous situaons and accidents 15
2.7 Signage 16
3.1 Combi tools 17
3.2 Cuers 18
3.3 Spreaders 19
3.4 Rescue rams 20
3.5 Operang condions 20
3.6 Type plate 20
3.4 Rescue rams 20
4.1 Overview of SMART-FORCE appliances 21
4.2 Cuer 22
4.3 Rescue rams 23
4.4 Spreaders 24
4.5 Hydraulic supply 25
4.6 Electrical supply, using a combi tool as an example 26
4.7 Underwater use 26
4.7 Communicaon module and radio connecon 28
4.8 Operang SMART-FORCE appliances 30
4.9 Device registraon for SMART-FORCE rescue devices 31
4.10 Accessories 32
4.10 Replacing blade inserts (PLUS) 35
4.11 Replacing the spreader ps 37
5.1 Safety instrucons 38
5.2 Cung (cuers, combi tools) 38
5.3 Pressing (rescue rams) 39
5.4 Spreading (spreaders, combi tools) 40
5.5 Pulling (spreaders, combi tools, rescue rams) 41
5.6 Squeezing (spreaders, combi tools) 42
5.7 Liing (spreaders, combi tools, rescue rams) 43
5.8 Peeling (spreaders, combi tools, rescue rams) 43
6.1 Charger technical data 44
6.2 Special safety instrucons 44
6.3 Intended use 46
6.4 Mains connecon 46
6.5 Li-ion baery 46
6.6 Charging process 47
6.7 Maintenance 48
7.1 Safety instrucons 49
7.2 Transport inspecon 49
7.3 Symbols on the packaging 50
7.4 Disposal of packaging 50
7.5 Storage 50
8.1 Safety instrucons 51
8.2 Checks 51
8.3 Shut-down (end of work) 52
8.4 Advantages of device registraon 53
9.1 Safety instrucons 54
9.2 Upkeep and maintenance 54
9.3 Maintenance aer operaon in humidity 55
9.4 Maintenance aer underwater use 55
9.5 Maintenance schedule 55
These operang instrucons provide important informaon on using SMART-FORCE appliances.
To assure safety at the workplace, always observe all safety and handling instrucons contained
in this document.
Furthermore, the local accident prevenon regulaons and general safety determinaons
applicable to the operaon site of the equipment must also be observed.
Before starng any work you must read these operang instrucons thoroughly! They are
a component of the product and must be stored in a known locaon that is accessible to
personnel at all mes.
This documentaon contains informaon about the operaon of your appliance, regardless of
which type of appliance it is. For this reason, you will also nd explanaons that do not relate
directly to your appliance.
All informaon, technical specicaons, graphics and illustraons contained in these Operang
Instrucons are based on the most up-to-date data available at the me these instrucons
were created.
In addion to thoroughly reading the operang instrucons, we also recommend that you
undergo training and instrucon in handling (possible uses, operaonal taccs, etc.) the rescue
equipment from one of our qualied trainers.
In these operang instrucons, warnings are idened by symbols.
The individual warnings are introduced by signal words expressing the degree of danger.
These warnings must be heeded to prevent accidents, injury and property damage.
… points out an immediately dangerous situaon which can cause death or
severe injury if it is not avoided.
…points out a potenally dangerous situaon which can cause death or
severe injury if it is not avoided.
…points out a potenally dangerous situaon which can cause minor or
slight injury if it is not avoided.
…points out a potenally dangerous situaon which can cause property
damage if it is not avoided.
…emphasises useful ps and informaon for ecient, trouble-free
operaon.
All informaon and instrucons in these operang instrucons were compiled under
consideraon of the applicable standards and regulaons, the current state of technology and
our long-standing knowledge and experience.
The manufacturer assumes no liability for damages due to:
• Non-observance of the operang instrucons
• Improper use
• Assigning untrained personnel
• Unauthorised modicaons
• Technical changes
• Use of impermissible replacement parts
• Use of non-original accessories
For special designs or due to technical changes, the actual scope of supply for may dier from
the explanaons and representaons described.
All texts, illustraons, drawings and images in these operang instrucons may be used freely
without prior authorisaon.
Addional informaon, images and diagrams are available on our home
page: www.weber-rescue.com.
The warranty provisions are included with the sales documentaon as a separate document.
Our Customer Service would be happy to provide you with technical informaon.
Service Center, Güglingen
Phone: +49 7135 71 10112
E-mail: servicecenter@weber-rescue.com
When contacng our Customer Service, please provide the idencaon,
type and year of manufacture of the appliance. This informaon can be
found on the type plate.
For further processing, please complete
the RMA document in full:
Service Center, Losenstein
Phone: +43 7255 6237-12473
E-mail: ATL.Servicecenter@weber-rescue.com
For quesons regarding spare parts, service and repair, please contact
our cered local service partners. Scan the following QR code for an
overview of our worldwide service and sales network.
This secon of the operang instrucons presents a comprehensive overview of all important
safety aspects for opmal protecon of the operang personnel as well as for safe, trouble-free
operaon.
Non-observance of the handling and safety instrucons presented in these Operang
Instrucons can result in serious dangers.
The hydraulic baery tools are designed and tested exclusively for the intended applicaons
described here. All other acvies are fundamentally prohibited.
All baery tools are designed as one-man appliances and are therefore to be operated by only
one person.
(RSC 170 S-FORCE, RSC 170 PLUS S-FORCE, RSC 190 S-FORCE, RSC 190 PLUS S-FORCE,
RSC 200 S-FORCE, RSC F7 S-FORCE)
• The baery-powered cung appliances are used exclusively for cung doors and
roof beams, pillars and door sills, the ring and the spokes of the steering wheel.
• If possible, for cung solid material, always use the rear part of the cuer unit as it
is equipped with special edges for cung round material.
• In industrial applicaon, the appliances can also be used to cut pipes, structural
steels, proles, sheets and cables.
(SP 44 AS S-FORCE, SP 54 AS S-FORCE, SP 50 BS S-FORCE)
• The baery-powered spreading appliances can be used for opening doors, liing
vehicles or other moveable loads, pushing away and moving vehicle parts and loads,
and squeezing pipes and e bars.
• If possible, always use the ps of the spreader for squeezing.
• The spreader ps can also be used as a peeling tool.
• The chain set is solely to be used for pulling.
(SPS 270 MK2 S-FORCE, SPS 360 MK2 S-FORCE, SPS 370 MK2 S-FORCE, SPS 400
MK2 S-FORCE, SPS 480 MK2 S-FORCE, RIT-TOOL S-FORCE)
• The baery-powered combi tools may be used for the specied purposes of both
the cuers and the spreaders. The spreader ps can also be used as a peeling tool.
(RZ 1-910 S-FORCE, RZT 2-1170 S-FORCE, RZT 2-1360 S-FORCE,
RZT 2-1500 S-FORCE)
• The appliances are used to li and push up steering columns, vehicle roofs and
other vehicle parts.
• In addion, under certain condions and whilst exercising parcular care, rescue
rams can be used for support, liing and sening.
• Spreaders and combi tools may only be used with the appropriate chain set and
pulling device. Pulling chains are exclusively for pulling away obstacles and loads
and for enlarging openings to free trapped persons.
Any use other than intended use and/or other type of use of these
appliances can cause dangerous situaons!
Therefore, it is absolutely necessary to:
» Only use the appliances for the intended uses described above.
» Observe all other informaon regarding proper use of the appliances in
Chapter 5 (Possible uses).
All S-FORCE equipment (cuers, spreaders, combi tools and rescue rams) are
intended for use in the professional or industrial sector and not for private use!
In addion to the occupaonal safety informaon in these operang instrucons, the safety,
accident prevenon and environmental prevenon regulaons applicable to the operaon site
of the appliance must also be observed. Thereby, the following applies in parcular:
• The operator must inform himself regarding the applicable occupaonal safety
regulaons and carry out a risk assessment to idenfy addional dangers arising
from the special work condions at the operaon site of the appliance.
• The operator must clearly regulate and determine responsibility for installaon,
maintenance and cleaning.
• The operator must ensure that all persons engaged with the appliance have
completely read and understood the operang instrucons.
• Furthermore, he must train the personnel at regular intervals and inform them of
the dangers associated with handling the appliance.
The operator is also responsible for ensuring that the equipment is always in a technically
awless condion. Therefore, the following applies:
• Aer each me the equipment is used, or at least once a year, a visual inspecon of
the appliance by an instructed person is required (per DGUV guideline 305-002 or
country-specic rules).
• Every three years, or whenever a doubt is raised about the safety or reliability of the
appliance, a funcon and load test must also be carried out (per DGUV guideline
305-002 or country-specic regulaons).
• Aer each use, but at least once a year, check the seal on the baery cover and the
housing in the sealing area for cracks and damage. Lubricate the seal with colourless
lubricant WD40 or MegaÖl Plus with PTM.
• The appliance must be tested for leaks at least once a year or if there is any doubt
about its reliability.
Maintenance work can be carried out by instructed persons. Maintenance
measures and repairs may only be carried out by the appliance manufacturer,
or by specialist personnel trained by the appliance manufacturer and the
authorised service partners. Connuous training and instrucon by the
appliance manufacturer is mandatory for a valid training cercate.
Este manual sirve para los siguientes modelos
30
Tabla de contenidos
Otros manuales de Herramientas de Weber Rescue Systems
Weber Rescue Systems
Weber Rescue Systems BC 250 Manual de usuario
Weber Rescue Systems
Weber Rescue Systems BC 250 MK2 Manual de usuario
Weber Rescue Systems
Weber Rescue Systems TACTICAL BC 250 E-FORCE2 Manual de usuario
Weber Rescue Systems
Weber Rescue Systems IP-BAG SMALL Manual de usuario
Weber Rescue Systems
Weber Rescue Systems E-FORCE3 Manual de usuario
