WDP ANGEL Manual de usuario

• This Operator’s and User’s

Manual is in English.

• It contains important safety

guidelines and Instructions.

• Should you be unsure at any

stage, or unable to understand

the contents within this manual

you must seek expert advice.

• Le mode d’emploi est en

Anglais.

• Il contient des instructions

et mesures de sécurité

importantes.

• En cas de doute, ou s’il vous

est impossible de comprendre

le contenu du monde d’emploi,

demandez conseil à un expert.

• Este manual de (operarios y)

usarios està en Inglés.

• Contiene importantes normas

de seguridad e instrucciones.

• Si no esta seguro de algún

punto o no entiende los

contenidos de este manual

debe conultar con

un experto.

• Diese Bedienungs- und

Benutzeranleitung ist in

Englisch.

• Sie enthält wichtige

herheitsrichtlinien

und -bestimmungen.

• Sollten Sie sich in irgendeiner

Weise unsicher sein, oder

den Inhalt dieses Heftes nicht

verstehen, lassen Sie siche

bitte von einem Experten

beraten.

Contents

General Warnings 2

Switching on your Angel 3

Turning the Angel off 3

Navigation switch 4

Replacing the 9v battery 4

Switching Angel eyes on/off 5

OPTO board 5

Macro line hose 5

Propellant air/nitrogen supply 6

Adjusting the ASA position 6

Installing an air nitrogen system 6

Bolt removal and rotor breech 7

Velocity adjustment 7

OLED menu 8-9

Modes

Semi Auto 10

NPPL 10

PSP 10

MILLENNIUM 10

XBall/NXL 10

CFOA 11

Full Auto 11

Demo 11

Custom Semi 11

Breakout 11

Soft breakout 11

Hard breakout 11

Ramp 12

Parameters

Valve dwell 12

De-Bounce 12

Loader speed delay 13

MROF eyes on/off 13

Breakout 14

Ramp 14

Shot % ﬁltering 14

Anti bolt stick 15

Software version 15

Factory reset 15

Game timer alarm 16

Tournament lock 16

General care and cleaning

Left & right cut-aways 17

General assemblies 18-19

In-line regulator service & assembly 20

Rubber ﬁnger detent 21

Angel eyes servicing 22

Angel eyes removal 23

LPR adjustment 24

LPR assembly removal

& replacement 25

LPR spool removal 26

Exhaust valve guide removal 27

Exhaust valve stem removal 27

Ram removal 28

Magnetic force trigger adjustment 29

Front and back stop position

adjustment 29

Trigger activation position 30

Wiring connections 30

Fault ﬁnding 31-32

Useful conversions 31

Warranty - EEC/ROW 33-34

Warranty - USA/Canada 35-36

Warranty card 37

ADHERE STRICTLY TO THESE AND ALL OTHER SAFETY INSTRUCTIONS AND GUIDELINES

• The ANGEL is not a toy.

• Careless or improper use, including failure to follow instructions

and warnings within this Operator Manual and attached to the

ANGEL could cause death or serious injury.

• Do not remove or deface any warnings attached to the ANGEL.

• Paintball industry standard eye/face/ear and head protection

designed speciﬁcally to stop paintballs and meeting ASTM

standard F1776 (USA) or CE standard (Europe) must be worn

by user and any person within range.

• Must be at least 18 years of age to purchase the ANGEL.

• Persons under 18 years of age must have adult supervision

when using or handling the ANGEL.

• Observe all local and national laws, regulations and guidelines.

• Use only on professional paintball ﬁelds where codes of safety

are strictly enforced.

• Use 0.68 calibre paintballs only.

• Keep the ANGEL switched off until ready to shoot.

• Treat every Angel as if it is loaded.

• Never point the ANGEL at anything you do not intend to shoot.

• Do not shoot at persons at close range.

• Do not shoot at fragile objects such as windows.

• Always measure your Angels velocity before playing paintball,

using a suitable chronograph.

• Never shoot at velocities in excess of 300 feet (92 meters)

per second, or at velocities greater than local or national laws allow.

• Do not ﬁre the ANGEL with the breech open or without the bolt

in the breech, as high pressure gas will be emitted.

• Use compressed air/nitrogen gas only. Do not use CO2.

• Do not exceed 850 psi (58 bar) input pressure.

• Always follow instructions, warnings and guidelines given with

any ﬁrst stage regulator you use with the ANGEL.

• Do not ﬁre the ANGEL with the breech release knob in the

unlocked position.

• Never look into the barrel or breech area of the ANGEL whilst the

Angel is switched on and able to ﬁre.

• Never put your ﬁnger or any foreign objects into the breech or

paintball feed tube of the ANGEL

• Never allow pressurised gas to come into contact with any part

of your body.

• Always switch off the ANGEL when not in use.

• Always ﬁt a barrel blocking device to your ANGEL when not

in use on the ﬁeld of play.

• Always remove all paintballs from the ANGEL when not in use

on the ﬁeld of play.

• Always remove the ﬁrst stage regulator and relieve all residual

gas pressure from the ANGEL before disassembly.

• The ANGEL can hold a small residual charge of gas, typically

2 shots, with the ﬁrst stage regulator removed. Always discharge

the Angel in a safe direction to relieve this residual gas pressure.

• Always remove ﬁrst stage regulator and all residual gas pressure

from the ANGEL for transport and storage.

• Always follow warnings and guidelines given with your ﬁrst stage

regulator for safe transport and storage.

• Always store the ANGEL in a secure place.

• THIS OPERATOR’S MANUAL MUST ALWAYS ACCOMPANY THE

PRODUCT IN THE EVENT OF RESALE OR NEW OWNERSHIP.

• SHOULD YOU BE UNSURE AT ANY STAGE YOU MUST

SEEK EXPERT ADVICE.

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

· Angel is LIVE and capable of ﬁring.

To switch the Angel on press and hold the navigation

switch 1 inwards for up to 2 seconds. The Angel will

turn on and will automatically go into LIVE mode with

the eyes on. The display screen will illuminate and

will show the ﬁring Status of the Angel.

The LED on the rear of the grip frame will show blue.

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

· Ensure a barrel blocking device is ﬁtted to

the ANGEL.

· Ensure the hopper is removed from the

ANGEL.

· Ensure that there are no paintballs in the

ANGEL.

· Paintball industry standard eye/face/ear and

head protection designed speciﬁcally to stop

paintballs and meeting ASTM standard F1776

(USA) or CE standard (Europe) must be worn

by user and any person within range.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

1Push & hold

navigation

switch for

up to 2 secs

Switching on your Angel

Switch the Angel off by pressing and holding the

navigation switch 1in for 1 second. A goodbye

message will be displayed on the screen and the

Angel will power down.

Making the Angel SAFE

When you turn the Angel on the Angel is LIVE.

To make the Angel SAFE, either:

•Access the menu options by pushing the navigation

upwards and holding for 1.5 sec. This automatically

puts the Angel in SAFE.

•Choose SAFE from the menu options.

When the Angel is SAFE a screen similar to that below

will show. The screen will indicate the Angel is SAFE.

The screen will also indicate the mode you are in and

whether the tournament lock is on or off.

(See page 16).

Turning the Angel off

1Push & hold

for 1 sec

Gun status

Battery

status

Eyes

status

Ball

status

Game timer status

Screen shows Eyes off

and eyes are faulty. Screen shows Eyes off

and no ball present.

Mode

Tournament

lock status

Screen shows Eyes on

and ball detected

The functions, features and settings of the Angel

are controlled by a 3 directional navigation switch

located on the rear of the grip frame. The switch

can move up and down to scroll through features

and settings indicated on the display and can be

pressed in to select the highlighted function or

setting required.

Navigation switch

•Ensure that the Angel is off.

•If required switch the Angel off by pressing and

holding the navigation switch in for 1 second.

A goodbye message will be displayed on the screen

and the Angel will power down.

•Remove the right hand grip cheek 1by removing

the 3 screws 2 using a suitable 2mm Allen key.

•If a battery is already present carefully lift the

battery 3from its housing.

•Observe the battery polarity as marked on the

battery housing terminal and on the battery.

Always use a good quality fresh battery.

Replacing the 9v battery

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

· Ensure a barrel blocking device is ﬁtted to

the ANGEL.

· Ensure the hopper is removed from the

ANGEL.

· Ensure that there are no paintballs in the

ANGEL.

· Paintball industry standard eye/face/ear and

head protection designed speciﬁcally to stop

paintballs and meeting ASTM standard F1776

(USA) or CE standard (Europe) must be worn

by user and any person within range.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

The navigation switch is

located on the rear of the

grip frame and allows

access to the Angel 1

internal menu option.

Push the switch up or down

and hold for 1.5 seconds.

To navigate through the

options simply push the

switch up to scroll up and

push the switch down to

scroll down. Press the

switch inwards to make

a selection.

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND

GUIDELINES

· THE ANGEL IS LIVE AND CAPABLE OF DISCHARGING.

•Ensure that the Angel is on (see page 3).

•As default the Angel Eyes will always be ON

whenever the Angel is switched ON.

•The Angel eyes can be switched off by pulling and

holding the trigger 1for 1 second. The Angel’s

MROF will drop to its default MROF eyes off setting.

It will ﬁre 1 shot to conﬁrm that the eyes have been

switched off and the buzzer will sound once.

The eyes off symbol will be displayed on the

display screen.

•To turn the Angel eyes back on pull and hold the

trigger 1again for 2 seconds,. The MROF will

return to MROF eyes on setting (see page 15 for

factory default setting), the buzzer will sound twice

the eyes on symbol will be displayed on the display

screen.

•Should the eyes detect a malfunction due to a

component failure or the eyes becoming dirty they

will automatically turn themselves off and the MROF

will revert to its MROF eyes off setting (see page 15

for factory default setting), the display will indicate

that the eyes are off and that a ball is not detected.

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

· Ensure a barrel blocking device is ﬁtted to

the ANGEL.

· Ensure the hopper is removed from the

ANGEL.

· Ensure that there are no paintballs in the

ANGEL.

· Paintball industry standard eye/face/ear and

head protection designed speciﬁcally to stop

paintballs and meeting ASTM standard F1776

(USA) or CE standard (Europe) must be worn

by user and any person within range.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

•Ensure that the Angel is off.

•If required switch the Angel off by pressing and

holding the navigation switch in for 1 second.

A goodbye message will be displayed on the screen

and the Angel will power down.

•Remove the right hand grip cheek 1by removing

the 3 screws 2 using a suitable 2mm Allen key.

•If a battery is already present carefully lift the

battery 3from its housing.

•Observe the battery polarity as marked on the

battery housing terminal and on the battery.

Always use a good quality fresh battery.

Replacing the 9v battery Switching Angel eyes OFF/ON

Push & hold

for 2 secs.

The Angel incorporates the OPTO board. This board

is the latest development in trigger sensing function.

It achieves unsurpassed advancements in trigger

repeatability and sensitivity, its friction free non

mechanical operating switch results in faster shorter

and lighter trigger strokes that give the user higher

prolonged achievable rates of ﬁre.

OPTO board

• The Macro line hose may be removed from the

Macro line connectors to facilitate maintenance.

• Pull back the collet 1on the connector and keep

the collet depressed.

• Pull the Macro line hose 2out of the connector

ﬁrmly.

• Cut back the Macro line hose cleanly and square 3.

•

Push the hose ﬁrmly into the Macro line connector

to re-attach.

Important Note:

Please make sure that the macro-line is

trimmed back before re-insertion after it

has been removed.

Macro line hose

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

· Always follow instructions, warnings and

guidelines given with any ﬁrst stage regulator

you use with the ANGEL.

· Use compressed air/nitrogen gas only

DO NOT USE CO2.

· Only use a paintball regulator that has been

designed for air or nitrogen gas.

· Do not exceed 850 psi (58bar) input pressure

to the ANGEL.

· Take suitable precautions when using sharp

cutting instruments.

· The Macro Line hose must be cut back

cleanly and square prior to attachment

or re-attachment to ensure secure ﬁtment.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

The Angel is designed to operate on air/Nitrogen gas.

This needs to be supplied to the Angel at an ideal

pressure of 400psi (27.5 bar) using a suitable ﬁrst

stage regulator.

Adjusting the ASA position

on its mounting rail

The ASA connects to the grip frame of the Angel via

an integrated dovetail mounting rail 1that allows

the user to slide the ASA body along the rail to ﬁne

tune the mounting position of the ASA. The ASA body

is locked down onto the rail via two set screws 2

located within a central recess at the front and back

of the integrated rail, in order to move the ASA along

the rail you need to loosen off the two set screws 2

using a 3mm Allen key, once the desired position of

the ASA has been achieved tighten the set screws 2

to lock the ASA into position on the integrated rail.

Each Angel comes complete with a centrally ported

on/off Angel ASA allowing for the easy connection of

a preset air/nitrogen system for immediate use.

Before installing your pre-set system into the Angel

ASA always ensure that the on/off adjuster knob 3

is wound out approximately half way.

Be careful not to unscrew the ASA on/off adjuster

knob too far as it is possible to completely

disassemble the ASA. If this happens replace the

on/off adjuster knob by screwing it back on to the

ASA main body in a clock wise motion.

Propellant air/nitrogen supply Installing an air nitrogen system

ASA

assembly

Depression

Pin orientation

OFF

Decreasing velocity

The velocity adjusting screw is located on the lower

portion of the fore grip 1.

To decrease the velocity, insert a 3mm Allen Key 2

into the velocity adjusting screw and rotate clockwise

Increasing velocity

To increase the velocity insert a 3mm Allen key 2

into the velocity adjusting screw and rotate counter

clockwise.

NOTE: When reducing velocity allow at least four

shots for the complete system to re calibrate

to the new regulated pressure.

Velocity adjustment

2Increase

velocity

Decrease

velocity

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

The outer wear surfaces of the Bolt are made from

accetal (homopolymer) and the inner core is made

from glass re-enforced nylon. This is to ensure –

due to its high cycling speeds- the bolt does not

seize within the body. Eventually the bolt will show

signs of wear but this is dependant on its usage and

the environmental conditions.

It is important that the bolt is kept clean and

free from dirt or grit and that it is run dry with no

lubricant. We recommend that you clean your bolt

after each day of use.

Bolt removal is best achieved whilst the angel is

gassed up as this ensures that the ram is in the

rearward position ready for the bolt to be extracted.

• Ensure that the Angel is off or that it is in safe mode.

• Rotate the breech release knob 1clockwise until

it stops.

NOTE: The breech block WILL NOT OPEN when

the Angel is de-gassed and the ram and bolt are

in the forward position. To allow the breech to

rotate open, insert a squeegee into the barrel

bore and manually push the bolt back.

• Swing out the rotor breach block 2so that the bolt

is exposed.

• Extract the bolt 3by pulling it backwards.

• To replace the bolt follow the steps in reverse

order.

Bolt removal and rotor breech

· Ensure a barrel blocking device is ﬁtted to

the ANGEL.

· Ensure the hopper is removed from the

ANGEL.

· Ensure that there are no paintballs in the

ANGEL.

· Ensure the ANGEL is switched off via the

navigation switch on the rear of the grip frame

prior to ﬁtting your ﬁrst stage regulator.

· Paintball industry standard eye/face/ear and

head protection designed speciﬁcally to stop

paintballs and meeting ASTM standard F1776

(USA) or CE standard (Europe) must be worn

by user and any person within range.

· Always follow instructions, warnings and

guidelines given with any ﬁrst stage regulator

you use with the ANGEL.

· Use compressed air/nitrogen gas only

DO NOT USE CO2.

· Only use a paintball regulator that has been

designed for air or nitrogen gas.

· Do not exceed 850 psi (58bar) input pressure

to the ANGEL.

· Take suitable precautions when using sharp

cutting instruments.

· The Macro Line hose must be cut back

cleanly and square prior to attachment or re-

attachment to ensure secure ﬁtment.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

· Ensure a barrel blocking device is ﬁtted to

the ANGEL.

· Ensure the hopper is removed from the

ANGEL.

· Ensure that there are no paintballs in the

ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

Once you have accessed the Status menu the

Angel automatically reverts to SAFE

Status

The Status menu allows you to select between

Live/Safe, the Information display screen and

the Parameters setting.

• To access the Status menu press and hold the

navigation switch up or down for 1.5 seconds.

• Once in the Status menu using the navigation

switch scroll up or down to choose between

Live/Safe, Information and Parameters.

• Pressing the navigation switch inwards will select

the highlighted function.

Information

The Information screen will display all the relevant

information relating to the electronic settings of your

Angel.

• With the Angel on and Live push the navigation

switch up or down for 1.5 seconds.

• The Angel will be in the Status menu.

• Use the navigation switch to scroll through

the Status menu settings till Information

is highlighted.

• Push the navigation switch inwards to select the

Information menu.

• The following information will be displayed on the

OLED. Scroll up or down using the navigation switch

to view this information.

Parameters

The Angel’s settings can be easily adjusted from the

Parameters menu.

• With the Angel on and Live push and hold the

navigation switch up or down for 1.5 seconds.

• The Angel will be in the Status menu.

• Use the navigation switch to scroll through the

Status menu settings till Parameters

is highlighted.

• Push the navigation switch inwards to select the

Parameters menu.

The following functions are all accessed via the

navigation switch and can all be accessed and

adjusted from the Parameters display.

OLED menu

Status

Software version

Mode

Soft break-out setting

Hard break-out setting

Soft ramp setting

Hard ramp setting

Dwell time

MROF eyes on limit

MROF eyes off limit

De bounce level

Loader speed level

Shot % ﬁltering

Anti Bolt Stick

Angel eyes on/off

Game timer set

Alarm time set

Total shots ﬁred since reset

Battery voltage

Modes

Valve Dwell

De-bounce

Loader speed

MROF eyes ON

MROF eyes OFF

Breakout

Ramp feature

Shot Filter

ABS

Game Time Set

Alarm Time Set

The navigation switch is

located on the rear of the

grip frame and allows

access to the Angel 1

internal menu option.

Push the switch up or down

and hold for 1.5 seconds.

To navigate through the

options simply push the

switch up to scroll up and

push the switch down to

scroll down. Press the

switch inwards to make

a selection.

IMPORTANT NOTE

At any point when accessing the OLED

menu options - pulling the trigger will

return you to the SAFE screen.

IMPORTANT NOTE:

Tournament lock

To comply with some Tournament

rules some of the Angel’s features are

required to be locked down so that they

cannot be adjusted on the ﬁeld of play.

For more details see page 16.

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

· Ensure a barrel blocking device is ﬁtted to

the ANGEL.

· Ensure the hopper is removed from the

ANGEL.

· Ensure that there are no paintballs in the

ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

OLED Menu

STATUS

ParametersLive/Safe Information

Current

settings

Status

Software version

Mode

Soft break-out setting

Hard break-out setting

Soft ramp setting

Hard ramp setting

Dwell time

MROF eyes on limit

MROF eyes off limit

De-Bounce level

Loader speed level

Shot % ﬁltering

Anti Bolt Stick

Angel eyes on/off

Game timer set

Alarm time set

Total shots ﬁred since reset

Battery voltage

Modes

Valve Dwell

De-bounce

Loader speed

MROF eyes ON

MROF eyes OFF

Breakout

Ramp Feature

Shot Filter

ABS

Game Time Set

Alarm Time Set

Semi Auto

NPPL

PSP

Millennium

XBall/NXL

CFOA

Full Auto

Demo

Custom Semi

Soft Break-out

Break-out

Soft Ramp

Hard Ramp

Modes

• Ensure that the Angel is switched on.

• Ensure that you are not activating the trigger.

• Push and hold the navigation switch UP or DOWN

for 1.5 seconds.

• The Status menu will be displayed.

• Push the navigation button up to highlight the

iParameters menu.

• Push the navigation switch in to select the

Parameters menu.

• From the Parameters menu select the iMode

feature by pushing the navigation switch inward.

• Scroll up or down through the Mode options by

pushing the navigation switch up or down.

• Once the desired Mode setting has been reached

press the navigation switch inwards to save the

new setting.

• A Saved Mode message will be displayed.

The Parameters menu will be displayed.

Semi Auto

The Angel eyes will default to on whenever the Angel

is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when

a paintball is present and has been detected by the

Angel eyes.

With the eyes activated the MROF that the Angel will

ﬁre at is limited by the MROF eyes on level.

With the eyes turned off the MROF that the Angel will

ﬁre at is limited by the MROF eyes off level.

The Angel will ﬁre 1 shot for each pull of the trigger.

Break-out and Ramp settings do not function in this

Mode.

NPPL

The Angel eyes will default to on whenever the Angel

is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when

a paintball is present and has been detected by the

Angel eyes.

With the eyes activated the MROF that the Angel will

ﬁre at is limited by the MROF eyes on level.

With the eyes turned off the MROF that the Angel will

ﬁre at is limited by the MROF eyes off level.

The Angel will ﬁre 1 shot for each pull of the trigger.

Break-out and Ramp settings do not function in this

Mode.

PSP

The Angel eyes will default to on whenever the Angel

is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when

a paintball is present and has been detected by the

Angel eyes.

The ﬁrst 3 shots will be ﬁred in semi automatic.

On the 4th shot the Angel will ramp to a pre set

MROF set at 15.4 balls per second, provided that the

user maintains trigger pulls at a rate of or above 5

balls per second.

If the user stops ﬁring for more than 1 second the

initial 3 shots in semi automatic must be re initiated.

Millennium

The Angel eyes will default to on whenever the Angel

is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when

a paintball is present and has been detected by the

Angel eyes.

The rate of ﬁre will be capped at 15 shots per sec.

Ramping of shots is allowed once 8 BPS is achieved

the Angel may ramp up to 15 BPS only if 8 BPS or

greater is maintained. Once the trigger is released

only 1 additional shot may be discharged.

Additional break-out and ramp settings do not

function in this Mode.

X-Ball/NXL

The Angel eyes will default to on whenever the Angel

is made live via the navigation switch.

With the eyes activated the Angel will only ﬁre when

a paintball is present and has been detected by the

Angel eyes.

MODES

ADHERE STRICTLY TO THESE

AND ALL OTHER SAFETY

INSTRUCTIONS AND GUIDELINES

· Ensure a barrel blocking device is ﬁtted to

the ANGEL.

· Ensure the hopper is removed from the

ANGEL.

· Ensure that there are no paintballs in the

ANGEL.

· SHOULD YOU BE UNSURE AT ANY STAGE YOU

MUST SEEK EXPERT ADVICE.

MODE OPTIONS Page

Semi Auto 10

NPPL 10

PSP 10

Millennium 10

XBall/NXL 10

CFOA 11

Full Auto 11

Demo 11

Custom Semi 11

Break-out 11

Soft Break-out 11

Hard Break-out 11

Ramp 12

Otros manuales para ANGEL

Tabla de contenidos

Otros manuales de Equipo de paintball de WDP

WDP

WDP ANGEL G7 Manual de usuario

WDP

WDP ANGEL Manual de usuario

Manuales populares de Equipo de paintball de otras marcas

PLANET ECLIPSE

PLANET ECLIPSE EGO LV1 Manual de usuario

PLANET ECLIPSE

PLANET ECLIPSE GEO CS1 Manual de usuario

First Endeavor Paintball

First Endeavor Paintball The Quest Manual de usuario

PMI

PMI Piranha VTL Manual de usuario

Proto

Proto SLG ULTRALITE Manual de usuario

Bob Long Technologies

Bob Long Technologies Alias Intimidator Manual de usuario

Proto

Proto REFLEX RAIL Manual de usuario

MCS

MCS BOX DRIVE Manual de usuario

Spyder

Spyder MR1 Manual de usuario

Evil

Evil OMEN 2.0 Manual de usuario

GOG

GOG Envy Guía

PLANET ECLIPSE

PLANET ECLIPSE GSL Manual de usuario

PLANET ECLIPSE

PLANET ECLIPSE GTEK M170R Manual de usuario

Evil

Evil Pimp Kit Manual de usuario

PLANET ECLIPSE

PLANET ECLIPSE CS3 .68CAL Manual de instrucciones

Proto

Proto SWITCH EL Manual de usuario

Empire

Empire MINI Manual de usuario

Psychoballistics

Psychoballistics SILVER BULLET LCD Manual de usuario