WCP GreyT Elevator V3 Manual de usuario

GreyT Elevator V3 - User Guide
(Rev 1)
Page 2
wcproducts.com
Table of Contents
Table of Contents
What is the GreyT Elevator V3? �������������������������������������������������������������������������4
Recommended Tools �����������������������������������������������������������������������������������������5
Tubing Cut Guide ������������������������������������������������������������������������������������������������6
Hex Shaft Cut Guide �������������������������������������������������������������������������������������������8
Bearing Block Assembly Instructions ���������������������������������������������������������������9
Step 1 ������������������������������������������������������������������������������������������������������ 10
Elevator Assembly Instructions ��������������������������������������������������������������������� 11
Step 1 ������������������������������������������������������������������������������������������������������ 12
Step 2 ������������������������������������������������������������������������������������������������������ 13
Step 3 ������������������������������������������������������������������������������������������������������ 14
Step 4 ������������������������������������������������������������������������������������������������������ 15
Step 5 ������������������������������������������������������������������������������������������������������ 16
Step 6 ������������������������������������������������������������������������������������������������������ 17
Step 7 ������������������������������������������������������������������������������������������������������ 18
Step 8 ������������������������������������������������������������������������������������������������������ 19
Step 9 ������������������������������������������������������������������������������������������������������ 20
Step 10 ���������������������������������������������������������������������������������������������������� 21
Step 11 ���������������������������������������������������������������������������������������������������� 22
Step 12 ���������������������������������������������������������������������������������������������������� 23
Step 13 ���������������������������������������������������������������������������������������������������� 24
Step 14 ���������������������������������������������������������������������������������������������������� 25
Step 15 ���������������������������������������������������������������������������������������������������� 26
Step 16 ���������������������������������������������������������������������������������������������������� 27
Step 17 ���������������������������������������������������������������������������������������������������� 28

GreyT Elevator V3 - User Guide
(Rev 1)
Page 3Table of Contents
wcproducts.com
Step 18 ���������������������������������������������������������������������������������������������������� 29
Step 19 ���������������������������������������������������������������������������������������������������� 30
Step 20 - Falcon/CIM/MiniCIM Version ������������������������������������������������ 31
Step 21 - 775Pro Version ����������������������������������������������������������������������� 32
Step 22 ���������������������������������������������������������������������������������������������������� 33
Step 23 ���������������������������������������������������������������������������������������������������� 34
Step 24 ���������������������������������������������������������������������������������������������������� 35
Step 25 ���������������������������������������������������������������������������������������������������� 36
Step 26 ���������������������������������������������������������������������������������������������������� 37
Available Kits ��������������������������������������������������������������������������������������������������� 38
KIT-0032: GreyT Cascade Elevator V3 (2 Stage) ����������������������������������� 38
KIT-0033: GreyT Cascade Elevator V3 Gearbox (Falcon, 20:1) ������������ 39
KIT-0033: GreyT Cascade Elevator V3 Gearbox (775pro, 63:1) ����������� 39
WCP-0442: GreyT Cascade Elevator V3 ������������������������������������������������ 40
FAQ ������������������������������������������������������������������������������������������������������������������� 41
Revision Table ������������������������������������������������������������������������������������������������� 42

GreyT Elevator V3 - User Guide
(Rev 1)
Page 4
wcproducts.com
Table of Contents
What is the GreyT Elevator V3?
The Greyt Elevator is back with a third iteration! Elevators can be used to lift objects high
above the robot without extending reach and center of gravity outside the robot the way
an arm does. It can also lift the robot as well!
Notable features:
• Double chain lifting
• Dual motor options
• Falcon 500 support
• Bearings on all surfaces
• Congurabletobeastallorwideasyouneedittobe
• Minimal plates
• Easy to assemble and maintain

GreyT Elevator V3 - User Guide
(Rev 1)
Page 6Table of Contents
wcproducts.com
Tubing Cut Guide
The overall length for these tubes is for the elevator represented in the CAD model. This
canbechangedtottherequirementsofanydesign.
Ensure that when cutting tubes, the distance from the last hole to the end of the tube
is the same as the image below. Usually this means that the tube length must be in
1/2”increments.Thisdistanceisrequiredforthebearingblocksandtubeplugstot
properly. If VersaFrame tubing is not used then tubes can be any length.
Note: It is recommended to cut the tubes longer than needed and then mill to the
correct length� Alternately, a chop saw may be used� The ends of the tubes should be
as at and square as possible.

GreyT Elevator V3 - User Guide
(Rev 1)
Page 7Table of Contents
wcproducts.com
Tubing Cut Guide (Continued)
The overall length for these tubes is for the elevator represented in the CAD model. This
canbechangedtottherequirementsofanydesign.
Ensure that when cutting tubes, the distance from the last hole to the end of the tube
is the same as the image below. Usually this means that the tube length must be in
1/2”increments.Thisdistanceisrequiredforthebearingblocksandtubeplugstot
properly. If VersaFrame tubing is not used then tubes can be any length.
Note: It is recommended to cut the tubes longer than needed and then mill to the
correct length� Alternately, a chop saw may be used� The ends of the tubes should be
as at and square as possible.

GreyT Elevator V3 - User Guide
(Rev 1)
Page 8Table of Contents
wcproducts.com
Hex Shaft Cut Guide
The “Pulley Shaft” and “Ratcheting Shaft“ lengths are universal regardless of the size of
the elevator made.
The “VersaPlanetary Connecting Shaft” should be measured and cut after the motors
have be installed to ensure the shaft is not too long. This shaft can have up to a 1/4” gap
between it and the VersaPlanetary output shaft.
The “Sprocket Shaft” length is dependent on the size of the elevator that is made.

GreyT Elevator V3 - User Guide
(Rev 1)
Page 9Table of Contents
wcproducts.com
Bearing Block Assembly Instructions
Eight of the Clamping Bearing Blocks will be assembled without the 1/4” ID x 3/4” OD
radial bearings. This is so the stages can be assembled seperately.
Note: Blue Loctite (McMaster P/N 1004A12) is recommended on all bolts that thread
into a tapped hole�

GreyT Elevator V3 - User Guide
(Rev 1)
Page 10Table of Contents
wcproducts.com
Step 1
Install all bearings as shown in the image below. The 6mm ID x 12mm OD radial bearing
will sit on the 1/4” shoulder on the bearing block, and the #8-32 x 3/8”L bolt will be used
to retain the bearing.
Note: Eight of the Clamping Elevator Blocks will be assembled without the 1/4” ID x
3/4” OD radial bearing or shoulder bolt�
Manuales populares de Sistema de elevación de otras marcas

morse
morse 82H-124 Manual de usuario

Braun
Braun NL955 Series Manual de usuario

haacon
haacon 1889.10 Manual de usuario

Protekt
Protekt AT 252 Manual de usuario

R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC
Nova Technology International, LLC NAS Series Manual de usuario

Genie
Genie Z-60/34 Manual de usuario

Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment
Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manual de programación







