Wattstopper WN-100 Manual de usuario

WN-100

Motion Sensor

Nightlight Switch

SPECIFICATIONS

WN-100-120

Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120VAC, 60Hz

Power Consumption . . . . . . . . . . . . . . . . . . . .0.92W maximum

Load Requirements . . . . .0-500W Incandescent, Fluorescent

. . . . . . . . . . . . . . . . . . . . . .and Compact Fluorescent

Horsepower Rating . . . . . . . . . . . . . . . . . . . . . . . . . . .1/6 HP

WN-100-277

Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277VAC, 60Hz

Power Consumption . . . . . . . . . . . . . . . . . . . . .0.92W maximum

Load Requirements . . . . . . . . . . . . . . . . . . . .800W Fluorescent

General

Time Delay Adjustment . . . . . . . .Fixed 15 minute, 30 minute,

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 hour, 2 hour

Operating Temperature Range . . . . . . . . . .32-131°F (0-55°C)

Operating Humidity Range . . . . . . .95% RH, non-condensing

Installation Instructions

US Patent Number:

4,787,722

UNIT DESCRIPTION

The Watt Stopper WN-100 is a motion sensing wall switch and nightlight that

controls lighting based on occupancy. The sensor uses passive infrared (PIR)

technology to sense human motion in a controlled space. It must have a clear

view of occupants in the space in order to detect occupancy. Obstructions such

as furniture blocking the sensor’s lens may prevent occupancy detection.

Note:Windows, glass shower doors, etc. will obstruct the WN-100’s view and

may prevent detection.

Through the WN-100’s mode selection, the user can specify ON functions and

time delay (see Sensor Adjustment & Programming section).

OPERATION

ON-Mode Functions (Manual-ON & Automatic-ON):

Manual-ON:

When the WN-100 is set to Manual-ON, users must turn lights on by pushing

the ON/OFF button. Lights will not turn on automatically with occupancy in

the Manual-ON mode. However, for a grace period of 30 seconds after

shut-off, the WN-100 will turn the load back on automatically when motion is

detected.

Automatic-ON:

In Automatic-ON mode, the WN-100 automatically turns lights on when a

designated space becomes occupied.

Note:In both Manual-ON and Automatic-ON, the ON/OFF button turns lights

off. The ON/OFF button must be pressed again to turn lights back on.

Time Delay:

The WN-100 automatically turns lights off after a space becomes vacant and

a preset time interval, or time delay, elapses. If lights are left on and no

motion is detected for the time delay selected (factory default = one hour), the

WN-100 automatically turns lights off.

Nightlight:

In the factory default mode, the nightlight remains on whenever the load is

off, regardless of occupancy.

The nightlight can be disabled from constant illumination (see “End User

Options” in the Sensor Adjustment & Programming section). However, when

motion is detected by the WN-100 while in Manual-ON mode, the nightlight

will automatically turn on and remain on until 90 seconds after the room

becomes vacant again. In this situation, nightlighting is provided only when

the room is in use.

If the nightlight remains disabled for 48 hours, it will automatically switch to

the default (enabled) mode.

COVERAGE PATTERNS

The WN-100 has a coverage range of 180 degrees and a maximum coverage

area of 300 sq. ft. To maintain its coverage capacity and optimally detect

motion, the WN-100 must have a clear and unobstructed view.

4.0'

(1.2m)

25'

(7.6m)

floor

Hot

Black

Neutral

White

Load

Red

Neutral

White

TOP

INDOOR USE ONLY

Ground

Green

Single-sensor wiring

25'

(7.6m)

10'

(3.1m)

WIRING

Visit our website for FAQs: www.wattstopper.com

INSTALLATION

Caution: A neutral connection is required for sensor operation.

A qualified electrician should be consulted regarding the availability of a

neutral in your particular installation.

1. Make sure that power has been

turned off at the circuit breaker.

2. Connect the existing wires to the

sensor terminals.

• Hot or Black to Line;

Load or Red to Load;

Ground or Green to Ground;

Neutral or White to Neutral.

•Do not allow any bare wire to

show above the connector.

3. Attach the sensor to the wall box

by inserting screws into the two

wide holes on the top and bottom

of the attached metal bracket. Line them up with the holes in the wall box

and tighten.

4. Turn on the circuit breaker. Push the ON/OFF button and the lights will

turn on.

TOP

INDOOR USE ONLY

TOP

INDOOR USE ONLY

Insert or wrap wire as shown. Tighten screw in the

clockwise direction.

CAUTION: TURN THE POWER OFF

AT THE CIRCUIT BREAKER BEFORE WIRING.

Call 800.879.8585 or 972.578.1699 for Technical Support

Wire insert

Optional

wire wrap

Strip Gauge

#12 – #14 AWG

Cu Wire Only

SENSOR ADJUSTMENT & PROGRAMMING

The WN-100 is designed for installation in hotel rooms and other semi-public

spaces. Custom setup features are intended for facility or installing personnel

only. Therefore, the Program Mode switch is located behind the cover plate. To

enable the Programming mode, the single DIP switch must be in the ON

(Program) position.

Programming the WN-100:

1. Slide the Program Mode switch (normally

covered by the light switch cover plate) to

the ON (Program) position. The nightlight

will flash, counting out the selected

operating mode (one flash then a pause =

mode 1, two flashes then a pause = mode

2, and so on)

2. Press the ON/OFF button to advance

through the modes. When you reach the

desired mode, slide the Program Mode

switch to the DOWN (End User) position.

3. When the Program Mode switch is returned

to the DOWN (End User) position, the

WN-100 will operate in Test Mode for five

(5) minutes. During this period, the time

delay will be 15 seconds and the WN-100

will operate as “Automatic-ON”. After five

(5) minutes, the WN-100 will use the

parameters of the selected mode.

Note: Do not leave the Program Mode Switch in the UP (Program) position. The

WN-100 will only operate properly in the DOWN (End User) position.

Mode Selections:

Flashes Time Delay Mode

R1 hour * Manual-On * Factory default

RR 2 hours Manual-On

RRR 30 minutes Manual-On

RRRR 15 minutes Manual-On

RRRRR 15 minutes Automatic-On

End User Options:

To disable the nightlight, press and hold the ON/OFF button. After one-half

second, the nightlight will display the Enabled/Disabled status (lit = nightlight

enabled, unlit = nightlight disabled). To change the status, continue to press and

hold the ON/OFF button. After five (5) seconds, the WN-100 changes state (for

more details, see “Nightlight” in the Operation section).

TOP

INDOOR USE ONLY

TOP

INDOOR USE ONLY

WN-100

Program

Mode

Switch

Nightlight

glows

behind lens

ON/OFF

Button

TROUBLESHOOTING

To test the WN-100:

Initiate the WN-100 Test Mode by sliding the Program Mode Switch up to the

ON (Program) position then back to the DOWN (End User) position.

When the switch is returned to the DOWN (End User) position, there will be a

five-minute test period. During this period, the time delay will be 15 seconds,

and the WN-100 will operate as “Automatic-ON”.

Move within the coverage zone of the WN-100 to trigger detection, then move

out of the coverage zone (see Coverage Patterns section). The load should

turn off within 15 seconds and the nightlight should subsequently turn on.

Repeat as necessary to ensure that the desired coverage areas are within

detection range.

Lights will not turn on (nightlight is illuminated):

1. Press ON/OFF button, lights should turn on. If not, check sensor wire

connections to the load.

2. Check the lamp.

Lights will not turn on (nightlight is NOT illuminated):

1. Check the sensor wire connections.

2. Make certain that the circuit breaker is on and functioning.

3. Call 800.879.8585 for technical support.

Lights turn OFF but nightlight does not turn ON:

1. Make sure the nightlight is not in Disable mode.

Call 800.879.8585 or 972.578.1699 for Technical Support

When ordering, add -W for white, -I for ivory for -A for light almond to the catalog number.

* One ASP-211 is included with each sensor.

WN-100-120 Motion Sensor Nightlight Switch

120VAC, 60Hz

WN-100-277 Motion Sensor Nightlight Switch

277VAC, 60Hz

ASP-211* Cover plate for single-gang box

ASP-422 Blank cover plate for double-gang box

ASP-432 Cover plate for double-gang box with switch option

ORDERING INFORMATION

WARRANTY INFORMATION

Watt Stopper/Legrand warranties its products to be free of defects in

materials and workmanship for a period of five (5) years. There are no

obligations or liabilities on the part of Watt Stopper/Legrand for

consequential damages arising out of, or in connection with, the use or

performance of this product or other indirect damages with respect to loss of

property, revenue or profit, or cost of removal, installation or reinstallation.

2800 De La Cruz Boulevard, Santa Clara, CA 95050

Technical Support: 800.879.8585 • 972.578.1699

www.wattstopper.com

02374r5 05/2005

Tabla de contenidos

Otros manuales de Accesorios de wattstopper

wattstopper

wattstopper PW-301 Manual de usuario

wattstopper

wattstopper PW-100 Manual de usuario

wattstopper

wattstopper EW-100-120 Manual de usuario

wattstopper

wattstopper LMDC-100 Manual de usuario

wattstopper

wattstopper DT-200 Manual de usuario

wattstopper

wattstopper Legrand FM-105 Manual de usuario

wattstopper

wattstopper RH-250 Manual de usuario

wattstopper

wattstopper DW 100 Manual de usuario

wattstopper

wattstopper PW-103N Manual de usuario

wattstopper

wattstopper CX-100 Manual de usuario

wattstopper

wattstopper LMLS-600 Manual de usuario

wattstopper

wattstopper LMDX-100 Manual de usuario

wattstopper

wattstopper DT-300 Manual de usuario

wattstopper

wattstopper FM-105 Manual de usuario

wattstopper

wattstopper DSW-301 Manual de usuario

wattstopper

wattstopper LMPW-102 Manual de usuario

wattstopper

wattstopper DT-200 Manual de usuario

wattstopper

wattstopper DT-305 Manual de usuario

wattstopper

wattstopper DT-300 Manual de usuario

wattstopper

wattstopper FSP-211 Manual de usuario

wattstopper

wattstopper UT-305 Manual de usuario

wattstopper

wattstopper Legrand LMPC-100 Manual de usuario

wattstopper

wattstopper DT-305 Manual de usuario

wattstopper

wattstopper DSW-100 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

wattstopper WN-100 Manual de usuario

Manuales populares de Accesorios de otras marcas