Watts HS Series Manual de instrucciones
Page 1of 18
HS -Series Reverse Osmosis Processor
With Built-in Pre-treatment and Membrane Flush
HS-Series
Pressure Tank
Float Tank
Models
Installation, Operation
&
Maintenance Manual
Page 2of 18
Before installing and/or operating Watts HS-Series Reverse Osmosis system, read this manual
completely. Keep this manual available for future reference. Further information is available by
contacting your local Watts distributor. Phone: (623)505-1512
Pressure Tank
Atmospheric Tank
Page 3of 18
TABLE OF CONTENTS
Specifications
Specifications Chart ……………………………… 4
Installation
Membrane installation ………………………………. 5
Inlet Connection ………………………………………. 6
Permeate Line Connection …………………..…….7
Pressure Tank Connection ……………………..….8
Atmospheric Storage Tank ………………………… 9
Plumb to Drain ………………………………………. 10
Operation
Start Up …………………………………………………..11
Alarms …………………………………………………….12
Maintenance
Quarterly Maintenance ………………………………13
Annual Maintenance ………………………………….14
Warranty
Warranty ………………………………………………….15
Glossary of Terms …………………………..………. 17
Page 4of 18
Specifications Complete System Packages
SPECIFICATIONS HS-450 HS-1000 HS-2400 HS-4800 HS-9600 HS-15000
DRY WEIGHT lbs. 300 310 350 650 750 950
WET WEIGHT lbs 550 1700 1750 4000 4100 4900
FEED WATER
COLD/Temp ½”/35°-70° ½”/35°-70° ½”/35°-70° ¾”/35°-70° ¾”/35°-70° 1”/35°-70°
HOT/ Temp ½”/70°-
140° ½”/70°-140° ½”/70°-
140° ¾”/70°-140°
¾”/70°-
140° 1”/70°-140°
FLOW RATE 2 GPM 4 GPM 8 GPM 12 GPM 24 GPM24 GPM
MAX.HARDNESS 17 Grains 17 Grains 17 Grains 17 Grains 17 Grains 17 Grains
MAX. TDS 2500 PPM 2500 PPM 2500 PPM 2500 PPM 2500 PPM 2500 PPM
MAX. IRON 0.1 MGL 0.1 MGL 0.1 MGL 0.1 MGL 0.1 MGL 0.1 MGL
MAX. PSIG 80 80 80 80 80 80
MIM. PSIG 25 25 25 25 25 25
DRAIN CONNECTION
FLOOR SINK MIM.
w/in 10 ft of
processor 1/ ¼” 1/ ¼” 1/ ¼” 1/ ¼” 1/ ¼” 1/ ¼”
ELECTRICAL
REQUIRMENTS VOLTS/AMPS
VOLTS/AMPS VOLTS/AMPS VOLTS/AMPS
VOLTS/AMPS
VOLTS/AMPS
RO PROCESSOR 115/11.0 115/23
OPTIONAL 220V 115/7.2 115/7.2 220/8.8 220/11.5 220/11.5 220/11.5
DELIVERY PUMP N/A 115/8.8 115/12.4 115/12.4 115/12.4 115/12.4
KDF FILTER N/A N/A N/A 115/2 115/2 115/2
Page 5of 18
Membrane Installation
Membrane
Brine Seal
Note: All Membrane Vessels are
clearly marked with flow direction.
Membrane “Brine Seal” is always
facing the water entry to Vessel.
Flow
Direction
Marking
Membrane
Vessel
Page 6of 18
HOT and/or COLD FEED WATER
CONNECTION
Hard plumb Hot and/or Cold water
Connections into Blending Valve
Using (L) Copper Pipe. Refer to table
Below.Valve is marked with HOT
and Cold connections.
RO FEED WATER
MIN/MAX
PSIG
PIPE
SIZE FLOW
RATE
HS-450 25/80 psig
½” 2 GPM
HS-100 25/80 psig
½” 4 GPM
HS-2400
25/80 psig
½” 8 GPM
HS-4800 25/80 psig
1” 12 GPM
HS-9600
25/80 psig
1 ¼” 24 GPM
HS-
15,000 25/80 psig
1 ¼” 24 GPM
Inlet Connection
NOTE: Use only
Teflon tape on all
threaded pipe.
Recommend installing Ball Valves
just prior to the Blending Valve.
Page 7of 18
Required fittings for Bulkhead & Tank
HS450 ½” MPT x 3/8C .
HS1000 ½” MPT x 3/8C
HS2400 ½” MPT x ½”C
HS4800 ¾” MPT x ¾” Female Slip Schedule 40 PVC
HS9600 1” MPT x 1” Female Slip Schedule 40 PVC
HS15,000 1” MPT x 1” Female slip schedule 40/80 PVC
Ball Valve used with Pressure Tank applications.
Note: Fittings are included with systems ordered as complete packages only!
Permeate Line Connection
HS-450 –HS2400 ½” Tubing or PVC pipe
HS4800 –HS15K 1” PVC Schedule 40 pipe
Permeate Line Connection
The HS Series permeate
connection is on the bulkhead
labeled “OUT TOTANK”
Page 8of 18
Pressure Tank Connection
Recommended tubing size
From bulkhead on unit to tank.
Note: Fittings are included with Systems ordered as complete packages only!
Note: Copper pipe is UNSUITABLE for any plumbing from RO Storage Tank!
Recommended materials include: Braided Stainless Steel Tubing, Hard Stainless.
Schedule 80 PVC or Poly Propylene is acceptable, if not being connected to boiler or
heating system.
HS-450 3/8”
HS-1000 3/8”
HS-2400 3/8”
HS-4800 ¾”
HS-9600 ¾”
HS-15,000 1”
HS450 -HS2400
Flexible poly tubing acceptable.
HS4800 –HS15,000
Schedule 80 PVC required.
Page 9of 18
Atmospheric Storage Tank
Bulkhead & Fitting Systems
Note: Copper pipe is UNSUITABLE for any plumbing from RO
Storage tank!
Recommended materials include: Braided Stainless Steel Tubing, Hard Stainless.
Schedule 80 PVC or Poly Propylene,if not being connected to boiler or heating system.
HS-450 3/8”
HS-1000 3/8”
HS-2400 3/8”
HS-4800 3/4 “
HS-9600 3/4”
HS-15,000 1”
Plumb Drain Connection located on Bulkhead of RO system to floor
drain,using table specifications below or appropriate air gap drain
with minimum drain size of 1 1/4”.
Note: Refer to local plumbing codes for requirements in your area.
Page 10of 18
Plumb to Drain
If the HS-Series was ordered with the atmospheric storage tank, the three tank float switches
have been installed at the factory. Check to insure the tank floats have not been damaged.
1. Connect the gray electrical cable containing four (4) wires from the M-Series control box
to the corresponding electrical connection on the atmospheric tank.
2. Connect the gray electrical cable from Control Box, labeled “By-Pass Solenoid”
to the By-Pass Solenoid.
3. Connect the gray electrical cable from Control Box, labeled “By-Pass Float
Switch” the By-Pass Float Switch.
4. Using the table below connect the RO processor Bulkhead to the tank using
specified tubing or PVC pipe.
HS-450 HS-1000 HS-2400 HS-4800 HS-9600-
HS15,000
Bulkhead
Connection 1/2” Poly 1/2” Poly 1/2” Poly ½” PVC 1” PVC
Drain Size Min.
1 ¼” 1 ¼” 1 ¼’ 1 ¼’ 1 ¼”
Drain Connection
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Otros manuales de Calentador de agua de Watts
Watts
Watts PLT-5 Guía de inicio rápido
Watts
Watts PVi CENTURION Manual de usuario
Watts
Watts Aerco INN 600N Guía
Watts
Watts DET-5-M1 Manual de usuario
Watts
Watts PVi CEN 1600 Manual de usuario
Watts
Watts Aerco AM Series Manual de usuario
Watts
Watts Aerco Innovation Series Manual de usuario
Watts
Watts Lync AEGIS Manual de usuario
Watts
Watts Aerco INN 600N Manual de usuario
Watts
Watts CEN2000 Manual de usuario
