Watts W-415-NF Manual de usuario

Installation, Operation and

Maintenance Manual

Model W-415-NF, W-525, W-525-NF, W-525P

IOM-WQ-W-415-NF_W-525_W-525-NF_W-525P

WARNING

Read this Manual BEFORE using this equipment.

Failure to read and follow all safety and use information

can result in death, serious personal injury, property

damage, or damage to the equipment.

Keep this Manual for future reference.

WQA Certiﬁed to NSF/ANSI standard

58, and NSF/ANSI standard 372 for lead free

compliance.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the

system.

WARNING

If you are unsure about installing your WATTS water ﬁlter, contact

a WATTS representative or consult a professional plumber.

IMPORTANT

Test the water periodically to verify that the system is

performing satisfactory.

Discard small parts remaining after the installation.

CAUTION

Failure to install the system correctly voids the warranty. Handle all

components of the system with care. Do not drop, drag or turn

components upside down.

Be sure the ﬂoor under the water ﬁlter system is clean, level and

strong enough to support the unit.

Watts, 13700 HWY 90 West San Antonio, TX 78245

NOTICE

Model 525P Shown

Thank you for choosing the Watts Reverse Osmosis Drinking Water

System. With proper care your water ﬁltration system will produce

high quality drinking water for many years.

Read carefully and follow the instruction in this manual before

proceeding with the actual installation. Pay particular attention to

all warnings, cautions and notes. Failure to do so could result in

personal injury or damage to the equipment or other property.

System and installation need to comply with state and local laws and

regulations.

Check List:

1) Reverse Osmosis Unit.

2) Water storage tank, 3 gallon volume (2.5 gallon @40psi).

3) Installation kit: tank ball valve, drain saddle clamp (¼" & 3/8"), feed

water valve, faucet assembly.

4) Manual.

Recommended Tools Lists

* Variable speed drill

* 1/8" and 1/4" drill bits

* 7/16" drill bit 1/2" and 9/16" open-end wrenches (or adjustable)

* Phillips screwdriver

* Utility knife

This reverse osmosis system contains a replaceable component

critical to the efﬁciency of the system.

Replacement of the reverse osmosis component should be with one

of identical speciﬁcations, as deﬁned by the manufacturer, to ensure

the same efﬁciency and contaminant reduction performance. The

product water shall be tested periodically to verify that the system is

performing satisfactorily.

Do not use with water that is microbiologically unsafe or of unknown

quality without adequate disinfection before or after the system.

1) Reverse Osmosis Unit

(525P Shown)

2) Water Storage

Tank 3 Gallon

3) Installation Kit

W-415-NF Filtration Process

Speciﬁcations:

1st stage: Sediment ﬁlter, 5 micron, 10"

2nd stage: Carbon block ﬁlter, 5 micron, 10"

3rd stage: TFC membrane, 50GPD @ 60PSI

4th stage: Inline carbon ﬁlter

Auto shut off valve

Operating pressure: 40-100 PSI

Operating temperature: 40-100°F

Please contact your local dealer at:

Replacement Parts

WATTS ITEM# DESCRIPTIONS SERVICE LIFE

FPMB5-978 Sediment ﬁlter, 5 micron, 10" 6-12 months

F101009 Carbon block ﬁlter, 5 micron, 10" 6-12 months

W-1812-50 TFC membrane, 50GPD @ 60 PSI 24-36 months

FI-CBA010J.38 Inline carbon ﬁlter 12-18 months

W-525 and W-525-NF Filtration Process

Speciﬁcations:

1st stage: Sediment ﬁlter, 5 micron, 10"

2nd stage: Carbon Block ﬁlter, 5 micron, 10"

3rd stage: Carbon Block ﬁlter, 5 micron, 10"

4th stage: TFC membrane, 50GPD @ 60 PSI

5th stage: Inline carbon ﬁlter

Auto shut off valve

Operating pressure: 40-100 PSI

Operating temperature: 40-100°F

Please contact your local dealer at:

Replacement Parts

WATTS ITEM# DESCRIPTIONS SERVICE LIFE

FPMB5-978 Sediment ﬁlter, 5 micron, 10" 6-12 months

F109009 Carbon block ﬁlter, 5 micron, 10" 6-12 months

W-1812-50 TFC membrane, 50GPD @ 60PSI 24-36 months

FI-CBA010J.38 Inline carbon ﬁlter 12-18 months

W-525P RO Filtration Process

Please contact your local dealer at:

Replacement Parts

Speciﬁcations:

1st stage: Sediment ﬁlter, 5 micron, 10"

2nd stage: Carbon Block ﬁlter, 5 micron, 10"

3rd stage: Carbon Block ﬁlter, 5 micron, 10"

4th stage: TFC membrane, 50GPD @ 60 PSI

5th stage: Inline carbon ﬁlter

Auto shut off valve

Operating pressure: 40-100 PSI

Operating temperature: 40-100°F

WATTS ITEM# DESCRIPTIONS SERVICE LIFE

FPMB5-978 Sediment ﬁlter, 5 micron, 10" 6-12 months

F109009 Carbon block ﬁlter, 5 micron, 10" 6-12 months

W-1812-50 TFC membrane, 50GPD @ 60PSI 24-36 months

FI-CBA010J.38 Inline carbon ﬁlter 12-18 months

Installation Quick Look

Please follow 4 color tubing diagram to complete installation Please follow 4 color tubing diagram to complete installation

Installation needs to comply with State and local plumbing regulations.

HOW TO MAKE A CONNECTION

1. CUT THE TUBE SQUARE

Cut the tube square. It is essential that the outside diam-

eter be free from score marks and that burrs and sharp

edges be removed before inserting into ﬁtting. For soft thin

walled plastic tubing we recommend the use of a tube

insert.

2. INSERT TUBE

Fitting grips before it seals. Ensure tube is pushed into the

tube stop.

3. PUSH UP TO TUBE STOP

Push the tube into the ﬁtting, to the tube stop. The collet

(gripper) has stainless steel teeth which hold the tube

ﬁrmly in position while the o-ring provides a permanent

leak proof seal.

4. PULL TO CHECK SECURE

Pull on the tube to check that it is secure. It is a good

practice to test the system prior to leaving site and/or

before use.

Disconnecting PUSH COLLET AND REMOVE TUBE To

disconnect, ensure the system is depressurized before

removing the tube. Push in collet squarely against face of

ﬁtting. With the collet held in this position, the tube can be

removed. The ﬁtting can then be re-used.

CAUTION: When cutting supplied tubes, predeter-mine the

length by measuring the distance between the components to

be connected.

No tools are needed to connect 4 colored tubes.

Connections Item No. Color of Tubing Description

A RO Faucet FU-WDF-905-CP Blue Pure water to the Faucet

B Feed Water Valve F560080 Green Feed Water to RO System

C Tank Ball Valve PPSV501222W Yellow Pure Water to Storage Tank

D Drain Saddle SC500B14 or WE-CU138B-Q Red Discharge Water to Drain

Drill a Hole for the Faucet in a Porcelain Sink

NOTICE

Most sinks are pre drilled with 1 ½" or 1 ¼" diameter hole that you can use for your RO

faucet. (If you are already using it for a sprayer or soap dispenser, see step 1)

Porcelain sinks are extremely hard and can crack or chip easily.

Use extreme caution when drilling. Watts accepts no responsibility for damage resulting

from the installation of faucet. Diamond tip bit recommended.

1) Determine desired location for the RO faucet on your sink and place a piece of masking tape

over where the hole is to be drilled. Mark the center of the hole on the tape.

2) Using a variable speed drill set on the slowest speed, drill a 1/8" pilot hole through both porce-

lain and metal casing of sink at the marked center of the desired location. Use lubricating oil

or liquid soap to keep the drill bit cool (If drill bit gets hot it may cause the porcelain to crack or

chip).

3) Using a 1 ¼"hole saw, proceed to drill the large hole. Keep drill speed on the slowest speed

and use lubricating oil or liquid soap to keep the hole saw cool during cutting.

4) Make sure the surroundings of the sink are cooled before mounting the faucet to the sink after

drilling and remove all sharp edges.

PUNCH A HOLE FOR THE FAUCET IN A STAINLESS STEEL SINK

NOTICE

If mounting faucet to a Stainless Steel Sink you will need a ½" & 1 ¼" hole punch.

The faucet opening should be centered between the back splash and the edge of

the sink, ideally on the same side as the vertical drain pipe.

Drill a ¼" pilot hole. Use a ½" hole punch and an adjustable wrench to punch the

hole in the sink. Change to the 1 ¼" hole punch to enlarge the hole.

The faucet can now be installed.

5) Drill a ¼" pilot hole. Use a ½" hole punch and an adjustable wrench to punch the hole in the

sink. Change to the 1 ¼" hole punch to enlarge the hole.

The faucet can now be installed.

Typical RO Faucet Installation

Drinking Feed Tube Connection

Non Air Gap Faucet

Locate the 3/8" threaded quick connect ﬁtting in the parts bag.

After the faucet has been mounted, thread the ﬁtting on the to faucet

stem. Connect the 3/8" blue feed tube to the 3/8" quick connect

ﬁt-ting on the faucet stem. The ﬁnal polishing ﬁlter is clipped on to

the top of the RO membrane housing. Attached to the polishing ﬁlter

is a 3/8" quick connect elbow ﬁtting. Attach the open end of the 3/8"

blue tubing from the RO faucet to the 3/8" quick connect elbow on

the polishing ﬁlter.

With Non Air-Gap faucets this will be the only tube connected to the

RO faucet.

Air Gap Faucet

Follow the drinking feed tube connection instruc-tions above. Con-

nect the ¼" drain tube from the RO module up to the ¼" ﬁtting on

the RO faucet. The 3/8" drain tube from the RO faucet will connect

to the 3/8" drain saddle.

BLACK RUBBER

WASHER

ESCUTCHEON PLATE

COUNTER TOP/SINK

LOCK WASHER

3/8” FAUCET CONNECTOR

3/8” BLUE TUBING FROM

RO MODULE

1/4” RED LINE TO

RO MODULE

3/8” Line to Drain

Saddle Valve

Non Air Gap Faucet Installation

Air Gap Faucet Installation

Black Rubber

Washer

Escutcheon Plate

COUNTER TOP/SINK

LOCK WASHER

3/8” FAUCET CONNECTOR

3/8” BLUE TUBING FROM

RO MODULE

Feed Water Valve Installation

Caution: Water supply line to the system must be from the cold water supply line only.

Hot water will severely damage your system.

Do not use Teﬂon tape with the Adapt-a-Valve.

1) Turn off the cold water supply to the faucet by turning the angle stop valve completely off.

2) Attach the adapt-a-valve as illustrated in the three photos above, choosing the conﬁguration that ﬁts your plumbing.

Drain Saddle Installation

Use the ¼" Drain Saddle with non air-gap faucet and 3/8" with air-gap faucet.

CAUTION

If you have a garbage disposal, do not install the drain saddle near it. Installation of the drain

saddle must be either above the garbage disposal, or if a second sink drain is available, install

it above the cross bar on the second drain. Installation of the drain saddle near a garbage

disposal may cause the drain line to plug.

1) Gather the pieces of the drain saddle

1 Black compression nut 1 Semicircle bracket with opening

2 Screws 1 Foam gasket

2 Nuts for screws 1 Semicircle bracket

2) The small square black foam gasket with a circle cut out of the middle must be applied to

the inside of the drain saddle. Remove sticky tape backing and stick to the drain saddle as

shown.

3) The drain saddle must be mounted at least 1 ½" above the nut of the P-trap or cross bar

from the garbage disposal to insure proper drainage. Assemble the drain saddle around the

drain pipe at the best available location. Using Phillips screw driver tighten screws evenly and

securely on both sides of the drain saddle. Keep the plastic compression nut off at this time.

Do not over tighten the screws. It may crack the drain saddle.

CAUTION

WARNING

Conguration for 3/8"

(with brass ttings)

*Insert white washer

Hot Cold

Supply Supply

Conguration for 1/2"

(without brass ttings)

<Fig 5>

STEP 3:

Mounting the Tank Ball Valve

Note: Do not tamper with the air valve on low side of storage

tank. It has been preset at 5-7 psi by the manufacturers.

1) With the provided teﬂon tape wrap 3-4 turns in a clockwise

direction around the male threaded connection on the top of the

storage tank,

2) Connect the ball valve to the thread. Make sure it is tight but not

over tight. See <Fig. 5>.

3) Connect the yellow tubing from to the tank ball valve. Push the

tubing in all the way to make sure it is properly seated.

4) Turn the tank ball valve off.

TOP VIEW OF TANK BALL VALVE

(PPSV501222W)

OFF POSITION ON POSITION

STEP 4:

Mounting the Drain Clamp

The drain saddle and part number to (SC500B14) will ﬁt most stan-

dard drain pipe ¼". It should be installed above the trap and on the

vertical tailpiece. See <Fig. 6>

1) Position the drain saddle in desired location, mark spot through

thread outlet, remove saddle.

2) Drill ¼" (6.3mm) hole into the drain pipe above the water line of

trap.

3) Align the hole drilled in the drain pipe with the drain saddle using a

drill bit or other narrow straight object and tighten clamp.

4) Make sure to align drain saddle to drilled hole. Attach drain saddle

to drain pipe and tighten the two screws evenly. See <Fig. 7>.

5) Connect black tubing to drain clamp.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de filtración de agua de Watts

Watts

Watts PWDWUV3 Manual de usuario

Watts

Watts IOM-WQ-PWSYS-FIL-ICE4 Manual de usuario

Watts

Watts UC-2 Manual de usuario

Watts

Watts Pure Water PWSYS-FIL-ICE1 Manual de usuario

Watts

Watts Pure H2O Series Manual de usuario

Watts

Watts WM-120-PT Manual de usuario

Watts

Watts WQT4 RO Series Manual de usuario

Watts

Watts Hydro-Safe Cold Bev Max-S2 Manual de usuario

Watts

Watts PWDWHCUC1 Manual de usuario

Watts

Watts IOM-WQ-PROSENSE Manual de usuario

Watts

Watts GTS450S Manual de instrucciones

Watts

Watts PWSCAB30K Pure Water Manual de usuario

Watts

Watts Hydrosafe HSFS Documento técnico

Watts

Watts WQT4RO11-50 Manual de usuario

Watts

Watts PWDWLCV2 Pure Water Manual de usuario

Watts

Watts OF1465 Manual de usuario

Watts

Watts WH-VIH1-SED-A-WHT-HSG Manual de usuario

Watts

Watts OneFlow OFPSYS Manual de usuario

Watts

Watts pure H2O H2O-FK101 Manual de usuario

Watts

Watts QTSTMMAX-2S-10M Manual de usuario

Watts

Watts Lync WQ-AS Manual de usuario

Watts

Watts Big Bubba BB-S100 Manual de usuario

Watts

Watts PWRO4ZRO Pure Water Manual de usuario

Watts

Watts OneFlow OF210-1 Manual de usuario

Manuales populares de Sistema de filtración de agua de otras marcas

Wisy

Wisy LineAir 100 Manual de usuario

Schaffner

Schaffner Ecosine FN3446 Series Manual de funcionamiento

Pentair

Pentair FLECK 4600 SXT Guía del usuario

H2O International

H2O International H20-500 Manual de usuario

Renkforce

Renkforce 2306241 Manual de usuario

Neo-Pure

Neo-Pure TL3-A502 Manual de usuario

FLTR

FLTR OBF Manual de usuario

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manual de usuario

Applied Membranes

Applied Membranes W-G844EM Manual de usuario

BEGA

BEGA 116 Manual de usuario

WATA

WATA Standard Manual de usuario

Price

Price FFU series Manual

Gaggenau

Gaggenau BRITA INTENZA 467873 Manual de usuario

Brita

Brita SAFF-100 Manual de usuario

HEISSNER

HEISSNER FPU24000-00 Manual de usuario

BGS technic

BGS technic 1518 Manual de usuario

Reverse Osmosis

Reverse Osmosis RF Series Manual de usuario

ubbink

ubbink Filtramax Series Manual de usuario