Watts 315 Manual de usuario
Watts Water Quality, 8716 W Ludlow Drive Suite #1, Peoria, AZ 85381
Phone: 800-659-8400 Fax: 800-659-8402
Manual #: 199613 Manual Date: 11/11/2015
IOM-WQ-315_415_525
Model 525P Shown
Installation, Operation
and Maintenance Manual
Under Counter Reverse Osmosis System
Model 315, 415, 525, 525P
WARNING
!
Please read carefully before proceeding with
installation. Your failure to follow any attached
instructions or operating parameters may lead to the
product’s failure.
Keep this Manual for future reference.
WARNING
!
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or
after the system.
If you are unsure about installing your WATTS water filter, contact
a WATTS representative or consult a professional plumber.
Test the water periodically to verify that the system is performing
satisfactorily.
Discard small parts remaining after the installation.
Failure to install the system correctly voids the warranty.
Handle all components of the system with care. Do not drop,
drag or turn components upside down.
Be sure the floor under the water filter system is clean, level
and strong enough to support the unit.
IMPORTANT
CAUTION
!
NOTICE
Thank you for choosing the WATTS WATER QUALITY Reverse Osmosis Drinking Water System. With proper
care your water ltration system will produce high quality drinking water for many years.
Read carefully and follow the instruction in this manual before proceeding with the actual installation. Pay
particular attention to all warnings, cautions and notes. Failure to do so could result in personal injury or
damage to the equipment or other property. System and installation need to comply with state and local laws
and regulations.
CHECK LIST:
1) Reverse Osmosis Unit.
2) Water storage tank, 3 gallon volume (2.5 gallon @40psi).
3) Installation kit: tank ball valve, drain saddle clamp (1/4” & 3/8”), feed water valve, faucet assembly.
4) Manual.
* Variable speed drill
* 1/8” and 1/4” drill bits
* 7/16” drill bit 1/2” and 9/16 open-end wrenches (or adjustable)
* Phillips screwdriver
* Utility knife
RECOMMENDED TOOLS LIST
This reverse osmosis system contains a replaceable component critical to the efciency of the system.
Replacement of the reverse osmosis component should be with one of identical specications, as dened by the
manufacturer, to ensure the same efciency and contaminant reduction performance.
The product water shall be tested periodically to verify that the system is performing
satisfactorily.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection
before or after the system.
1) Reverse Osmosis Unit
(525P Shown)
2) Water Storage
Tank 3 Gallon
3) Installation Kit
2
315 RO FILTRATION PROCESS
SPECIFICATIONS:
1st stage: Carbon Block lter, 5 micron, 10”
2nd stage: TFC membrane, 50GPD
3rd stage: Carbon Block lter, 5 micron, 10”
Auto shut off valve
Operating pressure: 40-100 PSI
Operating temperature: 40-100°F
Please contact your local dealer at:
REPLACEMENT PARTS
WATTS ITEM# DESCRIPTIONS SERVICE LIFE
F109009 Carbon block lter, 5 micron, 10” 6-12 months
W-1812-50 TFC membrane, 50GPD @ 60PSI 24-36 months
F109009 Carbon block lter, 5 micron, 10” 6-12 months
3
415 RO FILTRATION PROCESS
SPECIFICATIONS:
1st stage: Sediment lter, 5 micron, 10”
2nd stage: Carbon block lter, 5 micron, 10”
3rd stage: TFC membrane, 50GPD @ 60PSI
Auto shut off valve
Operating pressure: 40-100 PSI
Operating temperature: 40-100°F
Please contact your local dealer at:
REPLACEMENT PARTS
WATTS ITEM# DESCRIPTIONS SERVICE LIFE
IF-SP-1005 Sediment lter, 5 micron, 10” 6-12 months
F109009 Carbon block lter, 5 micron, 10” 6-12 months
W-1812-50 TFC membrane, 50GPD @ 60 PSI 24-36 months
W560033 Inline carbon lter 12-18 months
4th stage: Inline carbon lter
4
525 RO FILTRATION PROCESS
SPECIFICATIONS:
1st stage: Sediment lter, 5 micron, 10”
2nd stage: Carbon Block lter, 5 micron, 10”
3rd stage: Carbon Block lter, 5 micron, 10”
Auto shut off valve
Operating pressure: 40-100 PSI
Operating temperature: 40-100°F
Please contact your local dealer at:
REPLACEMENT PARTS
WATTS ITEM# DESCRIPTIONS SERVICE LIFE
IF-SP-1005 Sediment lter, 5 micron, 10” 6-12 months
F109009 Carbon block lter, 5 micron, 10” 6-12 months
F109009 Carbon block lter, 5 micron, 10” 6-12 months
W-1812-50 TFC membrane, 50GPD @ 60PSI 24-36 months
W560033 Inline carbon lter 12-18 months
4th stage: TFC membrane, 50GPD @ 60 PSI
5th stage: Inline carbon lter
5
525P RO FILTRATION PROCESS
SPECIFICATIONS:
1st stage: Sediment lter, 5 micron, 10”
2nd stage: Carbon Block lter, 5 micron, 10”
3rd stage: Carbon Block lter, 5 micron, 10”
Auto shut off valve
Operating pressure: 40-100 PSI
Operating temperature: 40-100°F
Please contact your local dealer at:
REPLACEMENT PARTS
WATTS ITEM# DESCRIPTIONS SERVICE LIFE
IF-SP-1005 Sediment lter, 5 micron, 10” 6-12 months
F109009 Carbon block lter, 5 micron, 10” 6-12 months
F109009 Carbon block lter, 5 micron, 10” 6-12 months
W-1812-50 TFC membrane, 50GPD @ 60PSI 24-36 months
W560033 Inline carbon lter 12-18 months
4th stage: TFC membrane, 50GPD @ 60 PSI
5th stage: Inline carbon lter
6
INSTALLATION QUICK LOOK
Please follow 4 color tubing diagram to complete installation
CAUTION: When cutting supplied tubes, predeter-
mine the length by measuring the distance between
the components to be connected.
No tools are needed to connect 4 colored tubes.
HOW TO MAKE A CONNECTION
1. CUT THE TUBE SQUARE
Cut the tube square. It is essential that the outside diameter
be free from score marks and that burrs and sharp edges be
removed before inserting into tting. For soft thin walled plastic
tubing we recommend the use of a tube insert.
2. INSERT TUBE
Fitting grips before it seals. Ensure tube is pushed into the tube
stop.
3. PUSH UP TO TUBE STOP
Push the tube into the tting, to the tube stop. The collet
(gripper) has stainless steel teeth which hold the tube rmly in
position while the o-ring provides a permanent leak proof seal.
4. PULL TO CHECK SECURE
Pull on the tube to check that it is secure. It is a good practice to
test the system prior to leaving site and/or before use.
Disconnecting PUSH COLLET AND REMOVE TUBE
To disconnect, ensure the system is depressurized before
removing the tube. Push in collet squarely against face of tting.
With the collet held in this position, the tube can be removed.
The tting can then be re-used.
Installation needs to comply with State and local plumbing regulations.
Connections Item No. Color of Tubing Description
ARO Faucet FU-WDF-905-CP Blue Pure water to the Faucet
BFeed Water Valve F560080 / F560070 Green Feed Water to RO System
CTank Ball Valve PSV501222W Yellow Pure Water to Storage Tank
DDrain Connector SC500B14/38 Red Discharge Water to Drain
7
8
Make sure the surroundings of the sink are cooled before mounting the faucet to
the sink after drilling and remove all sharp edges.
3)
4)
Determine desired location for the RO faucet on your sink and place a piece of
masking tape over where the hole is to be drilled. Mark the center of the hole on
the tape.
1)
Using a variable speed drill set on the slowest speed, drill a
1
/
8
“ pilot hole through
both porcelain and metal casing of sink at the marked center of the desired location.
Use lubricating oil or liquid soap to keep the drill bit cool (If drill bit gets hot it may
cause the porcelain to crack or chip).
Using a 1 ¼” hole saw, proceed to drill the large hole. Keep drill speed on the
slowest speed and use lubricating oil or liquid soap to keep the hole saw cool during
cutting.
2)
Drill a ¼” pilot hole. Use a
1
/
2
” Hole Punch and an adjustable wrench to punch the
hole in the sink. Change to the 1 ¼” Hole Punch to enlarge the hole.
5)
The faucet can now be installed.
If mounting faucet to a Stainless Steel Sink you will need a 1/2” & 1 ¼” Hole
Punch. The faucet opening should be centered between the back splash
and the edge of the sink, ideally on the same side as the vertical drain pipe.
Note:
Note:
Most sinks are pre drilled with 1 ½” or 1 ¼” diameter hole that you can use for your RO faucet. (If you are
already using it for a sprayer or soap dispenser, see step 1)
Porcelain sinks are extremely hard and can crack or chip easily.
Use extreme caution when drilling. Watts accepts no responsibility for
damage resulting from the installation of faucet. Diamond tip bit recommended.
DRILL A HOLE FOR THE FAUCET IN A PORCELAIN SINK
PUNCH A HOLE FOR THE FAUCET IN A STAINLESS STEEL SINK
9
Typical RO Faucet Installation
3/8”BLUE TUBING FROM
RO MODULE
1/4” RED LINE TO
RO MODULE
3/8” BLUE TUBING FROM
RO MODULE
Drinking Feed Tube Connection
Non Air Gap Faucet
Locate the 3/8” threaded quick connect tting in
the parts bag. After the faucet has been mounted,
thread the tting on the to faucet stem. Connect the
3/8” blue feed tube to the 3/8” quick connect t-
ting on the faucet stem. The nal polishing lter is
clipped on to the top of the RO membrane
housing. Attached to the polishing lter is a 3/8”
quick connect elbow tting. Attach the open end of
the 3/8” blue tubing from the RO faucet to the 3/8”
quick connect elbow on the polishing lter.
With Non Air-Gap faucets this will be the only tube
connected to the RO faucet.
Air Gap Faucet
Follow the drinking feed tube connection instruc-
tions above. Connect the 1/4” drain tube from the
RO module up to the 1/4” tting on the RO faucet.
The 3/8” drain tube from the RO faucet will connect
to the 3/8” drain saddle.
3/8” FAUCET CONNECTOR
LOCK WASHER
COUNTER TOP/SINK
ESCUTCHEON PLATE
BLACK RUBBER
WASHER
3/8” BLUE TUBING FROM
RO MODULE
3/8” FAUCET CONNECTOR
LOCK WASHER
COUNTER TOP/SINK
ESCUTCHEON PLATE
BLACK RUBBER
WASHER
3/8” LINE TO DRAIN
SADDLE
10
Use the 1/4” Drain Saddle with non air-gap faucet and 3/8” with air-gap faucet.
DRAIN SADDLE INSTALLATION
1)
2)
3) The drain saddle must be mounted at least 1 ½” above the nut of the P-trap or cross bar
from the garbage disposal to insure proper drainage. Assemble the drain saddle around
the drain pipe at the best available location. Using Phillips screw driver tighten screws
evenly and securely on both sides of the drain saddle. Keep the plastic compression
nut off at this time.
The small square black foam gasket with a circle cut out of the middle must be applied
to the inside of the drain saddle. Remove sticky tape backing and stick to the drain
saddle as shown.
1 Black compression nut 1 Semicircle bracket with opening
2 Screws 1 Foam gasket
2 Nuts for screws 1 Semicircle bracket
Gather the pieces of the drain saddle
Caution: Do not over tighten the screws. It may crack the drain saddle.
If you have a garbage disposal, do not install the drain saddle near it. Installation
of the drain saddle must be either above the garbage disposal, or if a second sink
drain is available, install it above the cross bar on the second drain. Installation of
the drain saddle near a garbage disposal may cause the drain line to plug.
Caution:
Turn off the cold water supply to the faucet by turning the angle stop valve completely off.
Attach the adapt-a-valve as illustrated in the three photos above, choosing the conguration that ts your
plumbing.
FEED WATER VALVE INSTALLATION
Conguration for 3/8”
(With Brass Fittings)
* Insert White Washer
Hot
Supply
Cold
Supply
Conguration for 1/2”
(Without Brass Fittings)
* Washer
Do not use Teon tape with the Adapt-a-Valve.WARNING:
Caution: Water supply line to the system must be from the cold water supply line only.
Hot water will severely damage your system.
1)
2)
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Sistema de filtración de agua de Watts
Watts
Watts PWSYS-WH-MICROZ Manual de usuario
Watts
Watts Hydro-Safe QTCLDBMX-1S-.5M Manual de usuario
Watts
Watts LYNC UV-H Manual de instrucciones
Watts
Watts Dormont Snap'N Go Manual de usuario
Watts
Watts Hydrosafe HSFS Documento técnico
Watts
Watts VB20 Series Manual de usuario
Watts
Watts OneFlow Manual de usuario
Watts
Watts Premier WP500320 UV-3 Manual de usuario
Watts
Watts WQT4RO11-50 Manual de instrucciones
Watts
Watts PWDWUV3 Manual de usuario
Watts
Watts ZRO-4 Manual de usuario
Watts
Watts OneFlow OFPSYS Manual de usuario
Watts
Watts Hydro-Safe QTESPMAX-2S-10M Manual de usuario
Watts
Watts pure H2O H2O-FK101 Manual de usuario
Watts
Watts OneFlow OF110-1 Guía de instalación
Watts
Watts Lync WQ-AS Manual de usuario
Watts
Watts IS-OR-NH Manual de usuario
Watts
Watts AERCO 58015-04 Manual del propietario
Watts
Watts Big Bubba BB-S100 Manual de usuario
Watts
Watts Lync AquaSolve LM8408-COM Manual
