Watts Premier WP-2 LCV Manual de usuario

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

MODELS:

WP-2 LCV, WP-2 BVC

Watts Premier, Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381

Phone: 800-752-5582 www.premierH2o.com Fax: 623-866-5666

Manual #: 199389 Manual Date: 02/05/2009

Please read carefully before proceeding with installation. Your failure to follow any attached instructions or

operating parameters may lead to the product’s failure.

Refer to enclosed warranty for operating parameters to ensure proper use with your water supply.

WP-2 BVC has been tested by Bio Vir as a Microbiological Water Purier based upon the

recommendations set forth in the USEPA Guide Standard and Protocol for Microbiological Water

Puriers (OPP Task Force Report, 1987)

Thank you for your purchase of a state of the art Watts Premier Water Treatment system.

WP-2 BVC Microbiological Water Treatment System:

Watts Premier WP-2 BVC water treatment system contains a patented State of the Art

Microbiological Filter. This lter has been independently tested and certied to remove disease

causing microorganisms from the drinking water, including bacteria, viruses and protozoan cysts.

While these water contaminants may not be in your water at all times, it provides a level of security

in the event there is a short term water concern such as a boil alert.

This lter has also been tested and certied to reduce chlorine tastes and odors from the drinking

water providing you great tasting water in addition to the comfort in knowing you have the protection

of the Microbiological Filter. See performance data sheet for individual contaminants and reduction

performance.

WP-2 LCV Water Treatment System:

Watts Premier WP-2 LCV water treatment system contains a heavy duty lead, cyst and VOC

lter block. This specialty formulated block is capable of reducing lead, cryptosporidium, Giardia,

Entamoeba as well as harmful Chemicals (See performance data sheet for complete list of

VOC’s). It is estimated that VOC’s are present in one-fth of the nation’s water supplies. These

water contaminants can enter ground water from a variety of sources including localized use of

herbicides and pesticides, gasoline or oil spills, leaking underground fuel tanks, septic system

cleaners, and chemicals used in the dry-cleaning industry. See performance data sheet for individual

contaminants and reduction performance.

System Maintenance

Just because you can not taste it, does not mean that it is not there. Many contaminants in the

drinking water are undetectable to the taste. Additionally, over time if you do not replace the

lter elements, other bad tastes and odors will be apparent in your drinking water. This is why

it is important to change your lters at the recommended intervals as indicated in this system

manual.

When replacing any of the lter elements, pay special attention to any cleaning instructions. Should

you have any further questions please refer to our web site at www.premierH2o.com or call our

customer service department at 1-800-752-5582.

Table of Contents

Maintenance Record......................................................................................................

Operational Parameters ................................................................................................

Contents of WP-2 System .............................................................................................

Tools Recommended For Installation ............................................................................

Installation......................................................................................................................

Drill / Punch a Hole for Watts Top Mount Faucet...........................................................

Watts Top Mount Faucet Installation .............................................................................

Adapt-a-Valve Installation................................................................................................

System Start Up...............................................................................................................

Filter Change..................................................................................................................

Parts Listing ..................................................................................................................

Performance Data Sheets..............................................................................................

California Certicate.......................................................................................................

Other Products by Watts................................................................................................

Warranty Registration.....................................................................................................

Removing Chlorine from your shower...........................................................................

Warranty .......................................................................................................................

10-12

15-16

Service Record

Date of Purchase:__________ Date of Install:___________ Installed by:_____________

NOTES:

Date Sediment

Filter

(6 months)

Date BVC/LCV

Filter

(6 Months)

BVC/LCV

Filter

(6 Months)

Sediment

Filter

(6 months)

Model Number:__________ Serial Number:___________

1 WP-2 Unit

2 Filters

1 Parts Bag

1 Faucet Assembly

If any of the items are missing, please contact Watts Premier prior to installing

Tools Recommended For Installation

A small knife

Variable speed drill

1/8” (3mm), 1/4” (6.4 mm) and 7/16” (11.0mm) drill bits

1/2” Diamond Tip Drill bit (for porcelain sinks)

1/2” hole punch (for stainless steel sinks)

1/2” and 5/8” open-end wrenches (or adjustable wrenches)

Phillips screwdriver

Contents of Under Counter System

Installation

This system has been designed to t under most kitchen sinks. Please read the entire manual carefully

before proceeding with installation.

Step 1: Mounting System Under Sink

(A) Locate a space under the sink that

allows the unit to be mounted close

to the cold water supply and allows

for easy access during maintenance

and filter changes. System must

be installed to the cold water supply

only. Allow approximately 2” (5cm)

clearance between the bottom of the

lter housing and the oor of the sink

cabinet.

(B) Using the mounting holes on the

bracket, mark the location for the

mounting screws on the cabinet wall

under the sink.

the marked location.

(D) Hang the module on the screws using

the mounting holes in the bracket.

Installation needs to comply with state and local plumbing regulations.

Operational Parameters

Maximum Minimum

Operational Temperature 100°F (37.8°C) 40°F (4.4°C)

Operating Pressure 85 psi (5.98 kg/cm²) 20 psi (1.406 kg/cm²)

pH Parameters 10 5

Flow Rate 0.5 GPM @ 60 psig

Sink

Green

Tubing

Blue

Tubing

HOT COLD

Counter Top

Two Stage Under Counter (WP-2)

Make sure the surroundings of the sink are cooled before mounting the

faucet to the sink after drilling and remove all sharp edges.

Step 3

Step 4

Determine desired location for the faucet on your sink and place a

piece of masking tape over where the hole is to be drilled. Mark the

center of the hole on the tape.

Step 1

Using a variable speed drill set on the slowest speed, drill a

“ pilot

hole through both porcelain and metal casing of sink at the marked

center of the desired location. Use lubricating oil or liquid soap to keep

the drill bit cool (If drill bit gets hot it may cause the porcelain to crack

or chip).

Using a 1/2” Drill Bit, proceed to drill the larger hole. Keep drill speed

on the slowest speed and use lubricating oil or liquid soap to keep the

hole saw cool during cutting.

Step 2

Drill a Hole for the Faucet in a Porcelain Sink

Punch a Hole for the Faucet in a Stainless Steel Sink

Drill a ¼” pilot hole. Use a

” Hole Punch and an adjustable wrench

to punch the hole in the sink.

Step 5

The faucet can now be installed.

If mounting faucet to a Stainless Steel Sink you will need a 1/2”

Hole Punch. The faucet opening should be centered between the

back splash and the edge of the sink, ideally on the same side as

the vertical drain pipe.

Note:

Note: Most sinks are pre drilled with 1 ½” or 1 ¼” diameter hole that you can use for your

faucet. (If you are already using it for a sprayer or soap dispenser, see step 1)

Porcelain sinks are extremely hard and can crack or chip easily.

Use extreme caution when drilling. Watts Premier accepts no responsibility for

damage resulting from the installation of faucet.

Diamond tip drill bit is recommended for drilling in porcelain.

Remove faucet base & spout from their respective plastic

bags. Feed the faucet tubing through the round rubber gasket

which you will nd in the faucets parts bag. Peel the white

backing from the upper side of the gasket and press rmly

on to the base of the faucet. From above the sink, feed the

faucet tubing & toggle bolt down through the .5” mounting

hole in the sink.

Peel the white backing from the bottom side of the rubber

gasket, align the faucet base so that the handle is on the

right side and press the faucet base down rmly over the

mounting hole. Turn the handle down (towards you) to the

“ON” position to reveal the tightening screw (located where

the spout will be inserted). Using a Phillips head screwdriver,

turn the screw clockwise until the toggle bolt secures the

faucet base snug onto the sink top, do not over torque toggle

bolt (5lb.in. max)

Once the faucet base is securely fastened to the sink top,

insert the faucet spout into the faucet base until it is fully

seated. Turn the handle up (away from you) to the “OFF”

position.

Connect the 3/8” blue tube from faucet to the 1/4” blue

tube from the system using the 3/8” x 1/4” union provided.

Remove the faucet battery from the plastic bag. Locate the faucet battery compartment drawer on the base of the faucet. Use

a small screwdriver to pry on the notch at the compartment drawer face and slide the drawer out. Insert the battery into the

battery compartment drawer.

NOTE: The + side of the battery faces up. The compartment drawer will not slide in if the battery is installed upside

down.

Once the battery is in place, slide the battery compartment drawer back into the base until it is ush.

When the battery is rst installed, both the red and green lights will ash to indicate that both lights are functional. Thereafter, it will

ash green only when the faucet handle is turned to the “ON” position. When your system is ready to be serviced (approximately

six months) you will see the light ash red when the handle is turned to the “ON” position.

NOTE: If your water usage is high the red light may activate sooner than six months indicating the need for lter

replacement.

This faucet provides an electronic monitor that will tell you when it is time to replace the lters in your water treatment

device. The light indicator will be green for the life of the lter, turning red once the life of the lter has been reached.

This can occur after six months of use, or sooner for heavy water usage. The battery life is expected to last one

year, however, under heavy use the battery may need to be replaced sooner. For replacement, look for battery

number CR2354 (Watts p/n:116082) which should be available at your local battery store or contact Watts Premier

at 800-752-5582. You may also order online at www.premierH2o.com.

WATTS Premier Monitored & Non-Monitored

(Top Mount) Faucet Installation

Step 6

Step 7

Step 8

Step 9

Step 10

Faucet Battery Installation

Minimum Maximum

Mounting Hole Size .5” 1.25”

Torque on Toggle Bolt 5lb.in. (max)

Line from Faucet

Line from Unit

Adapt-a-Valve Installation

(A) Turn off the main supply water to the house.

Note: Housing plumbing may be the opposite of that shown in Figure B.

(B) Turn off the cold water supply to the faucet by turning the angle stop valve clockwise

until it is completely off. Drain any water in the line by opening the faucet cold side.

that ts your plumbing.

(D) Attach the loose end of the green tube to the Adapt-a-Valve, remove a brass nut,

plastic sleeve and brass insert from the parts bag. Place nut on the tube rst, then

the plastic sleeve (small taper end of plastic sleeve must point to the end of tube) and

then insert the brass Insert into the end of the tube (see Figure C). Insert the green

tube into the ¼” opening on the adapt-a-valve until it stops. Slide nut and sleeve down

and thread onto the male pipe threads. Use a ½” wrench to securely tighten.

Conguration for 3/8”

compression ttings

Conguration for 1/2” ttings

(E) Turn on water supply and open the Adapt-a-valve. Check for leaks.

Correct installation of

the Adapta Valve

Figure B

System Start Up

(A) Turn faucet handle to the open position to start the ow of water through the unit. Run 7

gallons of water through the unit in order to ush out the normal black carbon nes (it will

“sputter” until the air is purged out) from the unit. Initially, the water may appear cloudy which

is due to tiny air bubbles and it will clear up shortly. Close the faucet when nished.

(B) Check for leaks. If you have any leaks, shut off the water supply to your system, tighten

any ttings / housings and restart unit.

HOT COLD

Figure C

Caution: Water supply line to the system must be from the cold water supply line.

Hot water will severely damage your system.

Watts Premier recommends changing the lter element every 6 months. However lter life

may vary depending on local water conditions and water use.

Use Watts Premier’s replacement cartridge only. Other lters may look the same, but only

lters by Watts are manufactured to t your WP-2 lter unit in order to ensure proper reduction

of water contaminants.

Sediment Pre-Filter

WP-2 BVC & WP-2 LCV Part# 104017

Carbon Block Filter

WP-2 BVC Part# 101003

WP-2 LCV Part# 101014

(A) Turn off incoming water supply to the WP-2 unit by

turning the needle valve on the adapt-a-valve clockwise.

Note: There will be water in the lter housing. Lift the

faucet handle to relieve the water pressure.

(B) Remove lter housing from lid by turning it to the left,

as shown in Figure D.

NOTE: Do not discard lter-housing o-ring.

(D) Clean inside of lter housing with warm soapy water

and rinse well to remove soap.

(E) Lubricate o-ring with water-soluble lubricant (i.e. K-Y Jelly ®).

NOTE: Do not use Petroleum based lubricants such as Vaseline ®.

(F) Seat o-ring in groove in lter housing and insert new lter cartridges into appropriate lter

housing.

(G) Screw lter housing onto lid as shown in Figure D.

(H) Turn on water supply to lter unit by turning needle valve on Adapt-a-Valve counter clockwise

and check system for leaks periodically over the next 24-48 hours.

Filter Change

To Loosen To Tighten

Figure D

To reset the electronic monitor during replacement of lters, simply slide out the

battery from the base of the faucet and reinsert.

Reset the Electronic Monitor Light

Performance Data Sheet

Watts Premier Inc.

8716 W Ludlow Drive Suite #1

Peoria, AZ 85381

WP-2 LCV

GENERAL USE CONDITIONS:

1: System to be used with municipal or well water sources treated and tested on regular basis to insure bacteriological safe

quality. DO NOT use with water that is micro biologically unsafe or of unknown quality without adequate disinfection

before or after the system. Systems certied for cyst reduction may be used on disinfected waters that may contain lterable

cysts.

2: Operating Temperature: Maximum 100o F (40.5o C) Minimum 40o F (4.4o C)

3: Operating Water Pressure: Maximum 85-psi (5.98 kg/cm2) Minimum 20-psi

4: Maximum ow Rate: 0.50 gpm (1.89 lpm)

5: Rated Capacity: 600 Gallons (2,200 liters)

RECOMMENDED REPLACEMENT PARTS AND CHANGE INTERVAL:

Note: Depending on incoming feed water conditions replacement time frame may vary.

Description Part Number Change time Frame Cost

Stage 1: Sediment: 5M-10 104017 6 Months or 600 gallons of water $ 3.50*

Stage 2: Carbon block 101014 6 Months or 600 gallons of water $28.95*

*All prices subject to change without notice

This system has been tested according to NSF/ANSI Standard 53 for the reduction of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as

specied in NSF/ANSI 53. Testing performed under standard laboratory conditions, actual performance may vary.

Substance Percent

Reduction

Inuent Challenge

Concentration

(mg/L unless noted)

Maximum Permissible

Product Water

Concentration

ALACHLOR* >98% 0.05 0.001

ATRAZINE* >97% 0.1 0.003

BENZENE* >99% 0.081 0.001

BROMODICHLOROMETHANE (TTHM)* >99.8% 0.300 +/- 0.30 0.015

BROMOFORM (TTHM)* >99.8% 0.300 +/- 0.30 0.015

CARBOFURAN (Furadan)* >99% 0.19 0.001

CARBON TETRACHLORIDE* 98% 0.078 0.0018

CHLOROBENZENE (Monochlorobenzene)* >99% 0.077 0.001

CHLOROFORM (TTHM)* >99.8% 0.300 +/- 0.30 0.015

CRYPTOSPORIDIUM (see Cyst) 99.99% minimum 50,000/mL 99.95%

CYST 99.99% minimum 50,000/mL 99.95%

2, 4-D* 98% 0.110 0.0017

DBCP (see Dibromochloropropane)* >99% 0.052 0.00002

1,2-DCA (see 1,2-DICHLOROETHANE)* 95% 0.088 0.0048

1,1-DCE (see 1,1-DICHLOROETHYLENE)* >99% 0.083 0.001

DIBROMOCHLOROMETHANE

(TTHM;Chlorodibromomethane)* >99.8% 0.300 +/- 0.30 0.015

DIBROMOCHLOROPROPANE (DBCP)* >99% 0.052 0.00002

o-DICHLOROBENZENE (1,2 Dichlorobenzene)* >99% 0.08 0.001

p-DICHLOROBENZENE (para-Dichlorobenzene)* >98% 0.04 0.001

1,2-DICHLOROETHANE (1,2-DCA)* 95% 0.088 0.0048

1,1-DICHLOROETHYLENE (1,1-DCE)* >99% 0.083 0.001

CIS-1,2-DICHLOROETHYLENE* >99% 0.17 0.0005

TRANS-1,2- DICHLOROETHYLENE* >99% 0.086 0.001

1,2-DICHLOROPROPANE (Propylene Dichloride)* >99% 0.08 0.001

CIS-1,3- DICHLOROPROPYLENE* >99% 0.079 0.001

DINOSEB* 99% 0.17 0.0002

EDB (see ETHYLENE DIBROMIDE)* >99% 0.044 0.00002

ENDRIN* 99% 0.053 0.00059

Otros manuales para WP-2 LCV

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de filtración de agua de Watts Premier

Watts Premier

Watts Premier WP-5 Instrucciones generales

Watts Premier

Watts Premier WP-4 BVC Instrucciones generales

Watts Premier

Watts Premier RO-PURE 531401 Manual de usuario

Watts Premier

Watts Premier HT-5-VOC-B Manual de usuario

Watts Premier

Watts Premier WP-4V Manual de usuario

Watts Premier

Watts Premier Zero Waste Retrofit Kit Manual de usuario

Watts Premier

Watts Premier WP-2 LCV Manual de usuario

Watts Premier

Watts Premier ZRO-4 Manual de usuario

Watts Premier

Watts Premier Filter-Pure UF3 Manual de usuario

Watts Premier

Watts Premier Filter-Pure UF3 Instrucciones de instalación y funcionamiento

Watts Premier

Watts Premier WP-2 LCV Manual de usuario

Watts Premier

Watts Premier 500029 Manual de usuario

Watts Premier

Watts Premier RO-TFM-4SV Manual de usuario

Watts Premier

Watts Premier DELUXE PLUS Manual de usuario

Watts Premier

Watts Premier CT-1 Manual de usuario

Watts Premier

Watts Premier FILTER-PURE Manual de usuario

Watts Premier

Watts Premier WP-1 LCV Manual de usuario

Watts Premier

Watts Premier Filter Pure UF3 Manual de usuario

Watts Premier

Watts Premier ZERO WASTE RETRO Manual de usuario

Watts Premier

Watts Premier WP-4V Manual de usuario

Watts Premier

Watts Premier RO-PURE Manual de usuario

Manuales populares de Sistema de filtración de agua de otras marcas

Wisy

Wisy LineAir 100 Manual de usuario

Schaffner

Schaffner Ecosine FN3446 Series Manual de funcionamiento

Pentair

Pentair FLECK 4600 SXT Guía del usuario

H2O International

H2O International H20-500 Manual de usuario

Renkforce

Renkforce 2306241 Manual de usuario

Neo-Pure

Neo-Pure TL3-A502 Manual de usuario

FLTR

FLTR OBF Manual de usuario

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manual de usuario

Applied Membranes

Applied Membranes W-G844EM Manual de usuario

BEGA

BEGA 116 Manual de usuario

WATA

WATA Standard Manual de usuario

Price

Price FFU series Manual

Gaggenau

Gaggenau BRITA INTENZA 467873 Manual de usuario

Brita

Brita SAFF-100 Manual de usuario

HEISSNER

HEISSNER FPU24000-00 Manual de usuario

BGS technic

BGS technic 1518 Manual de usuario

Reverse Osmosis

Reverse Osmosis RF Series Manual de usuario

ubbink

ubbink Filtramax Series Manual de usuario