Waters Andew Alliance OneLab+ Manual de usuario
INSTALLATION GUIDE
OneLab standalone server
Copyright © 2020 Andrew Alliance S.A.
About this manual
Read the user manual before using this device. Strictly follow usage and mainte-
nance instructions provided in the manual. It is the user’s responsibility to become
familiar with all available information concerning the correct use, care and limita-
tions of these products. If you are uncertain about the correct use or limitations of
the products, contact Andrew Alliance service and support. The manufacturer, the
distributor and their respective owners, employees, agents and representatives are
not responsible or liable for errors or omissions.
Information in this User Manual is subject to change without notice and does not
represent a commitment on the part of Andrew Alliance. Andrew Alliance assumes
no responsibility for any inaccuracies that may be contained in this User Manual.
Andrew Alliance makes no commitment to update or keep current the information in
this User Manual, and reserves the right to make improvements to this User Manual
and/or to the products described in this User Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete, we
would appreciate your comments and suggestions.
Safety instructions
• The device must always be completely switched o (cables
removed) before moving it.
• The user must maintain a distance of at least 20cm from the
product (WiFi antenna) while it is being installed and operated.
• The device is intended for indoor use only.
• Device maintenance has to be done exclusively by an Andrew
Alliance representative.
• If the device is used in a manner not specied by the manufac-
turer, the protection provided by the device may be impaired.
What’s in the package
Product overview
OneLab standalone server
(UP Squared system)
Power supply USB WiFi Adapter
(only for Service & Support use)
USB 3.0
USB 3.0 OTG USB 3.0 2x
DisplayPort
DC-IN
HDMI
Gigabit Ethernet 2x
Wi-Fi antenna
connectors
A. Installation of the standalone server
Unbox the
standalone
server.
Screw the 2 antennas
in the back.
Plug the standalone server into
a power source.
You will know that the OneLab Standalone Server is ready
when you will see the “onelab_standalone” network
in the list of Wi-Fi networks.
The server should become ready in less
than a minute.
12
3
4
onelab_standalone
B. Access to OneLab
1
2
3
Connect your compute to OneLab standalone WiFi network
a. Go to your Wi-Fi settings
and select the network
named “onelab_standalone”
b. Enter network password
“OneLab_Standalone”
Launch a web browser, type http://192.168.5.1
and log into OneLab using the credentials
IMPORTANT!
Change the OneLab credentials
http://
192.168.5.1
Work email: [email protected]
Password: onelab
a. On OneLab, click on the menu located in the top right
b. Click on “Prole settings”,
go to “Account Password” area
and create a new password
Annex 1: Pairing your connected device
with OneLab
Press 5 times the main button Wait the LED sign to turn blue
and blink
After a couple of minutes, the de-
vice will inform you when it is in
installation mode.
5 times
Connect your computer, tablet or smartphone to your device
Launch a web browser, type http://192.168.2.1,
follow the on-screen steps to continue installation
and take the steps 5 and 6 in consideration (next page).
A. Go to your Wi-Fi settings and select the network named
Andrew-718.xxxx.xxxxx or Stand-618.xxxx.xxxxx
1 2
3
4
xxxx.xxxxx is the device serial number
(for Andrew+, you can nd it on the door of the Optical Location Module
and for Pipette+ Stand+, you can nd it in the back of your device)
B. The LED sign will stop blinking when it’s successfully connected.
http://192.168.2.1
In case you need to pair the device (e.g. switch from Wi-Fi to Ethernet):
In case of Wi-Fi connection,
select the onelab_standalone wireless network.
At this step, ll the form with these information
then continue the installation.
If wired connection will be used, simply follow the instructions stated
in the pairing application.
5
6
Network password: OneLab_Standalone
Web address: http://192.168.5.1
Work email: [email protected]
Password: onelab
Annex 2: Power OFF the OneLab server
Never remove the server from the
power before switching it o.
Use the tip of a pen to press the reset
button for 5 seconds and wait until the
LED will turn OFF.
Then, you may unplug the device
from the power.
Technical data
SOC Intel® Atom ™ x7-E3950 (up to 2.0GHz)
Memory 8 GB (dual channel) LPDDR4
Graphics Intel® Gen 9 HD, supporting 4K Codec Decode and Encode for HEVC4, H.264,
VP8
Storage capacity 64 GB eMMC
Video & audio • HDMI 1.4b x1 4K @ 30 hz
• DP 1.2 4K @ 60 hz
• I2S audio port
USB • 2x USB2.0 + 2x UART (Tx/Rx) debug port (pin header)
• 3x UBS3.0 (Type A), 1x USB 3.0 OTG (Micro B)
Ethernet 2x Gb Ethernet (full speed, Realtek 8111G) RJ-45
RTC Yes
Expansion • 40 pin General Purpose bus + 4-channel 12-bit A/D converter 60 pin EXHAT
• 1x mini-PCIe (full-size, auto switch to m-SATA) M.2 2230 E key, SATA3
Operating system Linux
Power 5V DC-in at 4A-6A
Operating humidity 0% ~ 90% relative humidity, non-condensing
Operating temperature 32-140°F / 0~60°C
Dimensions 85.60 mm × 90 mm (3.37in x 3.54in)
Certications CE/FCC Class A, RoHS compliant, REACH
Andrew Alliance S.A.
Chemin Grenet 21
1214 Vernier (Geneve) Switzerland
Phone: +41 22 518 0357
Tabla de contenidos
